you have aviation maintenance experience by chance??
@badmatt422711 күн бұрын
No
@BrunoBoy391320 күн бұрын
Good video but get rid of the annoying background music
@terryfoster683623 күн бұрын
THANK YOU! Finally someone who made a video.
@Richard5873Ай бұрын
At 6:41 what was torque spec and thickness you set ?
@badmatt4227Ай бұрын
Axle holder 132-180 inch pounds
@Richard5873Ай бұрын
@badmatt4227 Thanks going to take mine off and put back on , to see if I have an alignment issue make brakes pulsating
@badmatt4227Ай бұрын
@@Richard5873 Do you have ABS?
@Richard5873Ай бұрын
@@badmatt4227 Yes
@badmatt4227Ай бұрын
@@Richard5873 I believe the pulse is the ABS and some ABS break fluid needs to replaced frequently. I would research.
@jeremymoore2411Ай бұрын
Best CD ever! Great video
@user-wg7dx7er8wАй бұрын
Hi 👋, Very nice job, I am in the process of changing my final drive belt on a Deuce 2003, that I have just purchased,
@mikeymadnezАй бұрын
1:18 Deez nuts
@chrisnchrissywalker9148Ай бұрын
I think I peed a lil from ALL the different clips of songs .... hilarious
@vin420772 ай бұрын
Do you know what size the 5 screws are that go through the latch and through the lid into the backing plate? 4 of mine are stripped.
@badmatt4227Ай бұрын
That has been so long ago, I don't remember.
@vin42077Ай бұрын
@@badmatt4227 thanks no worries all good... Harley had them at a dollar a pop
@eddielongshore20522 ай бұрын
I got confused on spacer locations and your video helped, thank you!
@ottodetroit2 ай бұрын
good idea about 1/4 " drive, Kiefer.
@badmatt42272 ай бұрын
Feels like a hundred years ago, First carburetor I worked on, I over tighten and broke the body.
@twitchtwitch90062 ай бұрын
this video helped a lot. keep up the great content
@charlikelso72272 ай бұрын
i need to do this after a few other YT University courses yours makes it look like i can ... curious how many copywrite hits you got on this video haha
@pescado_fn13862 ай бұрын
rip
@edwardcook26553 ай бұрын
What no screaming 😂😂😂😂😂
@sexyfiretoes84023 ай бұрын
channel locks work good for the hose clamp aswell if you don't have the special tool
@skrdykatjunior61253 ай бұрын
I have a big box super glued shut on both ends. Cannot open it with knife or scissors. Help!
@johncasor96983 ай бұрын
Remember this you are trusting that clicking tool is correct... but with a BEAM style Torque Wench it is spot on every try , and will do reverse..
@daletustison85503 ай бұрын
The problem with Exhaust manifold fasteners is overheating the poor quality stock manifolds. They shrink when they are overheated. To remove them either the bolts (Since they have sideways binding) Bolts do not have universal joints and some break. The answer is to cut the stock manifold with an angle grinder, Drive a machinist's splitting wedge into the kerf forcing it to break. the gap often opens up to an eight of an inch. Bolts are easy to remove. I usually have 1 broken but can turn it out with my fingers. Buy a new, (Up-Graded manifold. Simple fact is the biggest problem is miss information and parts salesmen. There is NO PROBLEM with the stock fasteners. Install all new fasteners. Saw the bracket to reach the one back bolt. Use a short (Scab) with a hole drilled into each end. Hold it with small vicegrips. Secure it with 2 self-tapping drill screws
@daletustison85503 ай бұрын
Do not wast your time in reinstalling the stock manifold. Unless you enjoy doing it over and over
@badmatt42273 ай бұрын
Complaining about a problem without also including a solution is called whining.
@user-gt9cj4yo7x4 ай бұрын
Such a great run- through! Thank you!
@TexasSheepdawg214 ай бұрын
Can you put a link in the description of where we can get those LED bulbs? Thank you.
@kennethharris45473 ай бұрын
Amazon
@TexasSheepdawg214 ай бұрын
Nice video though man. Just ribbing ya a bit on the background music. I guess we have to go to extreme lengths to keep from getting strikes on our channels. Mine has had so many, I quit making content. I was doing firearms and reloading vids.
@JoshiJosho-mf8oi4 ай бұрын
The hell is with that music? Are we fixing a truck or shopping for Chinese herbal tea? 😂
@TexasSheepdawg214 ай бұрын
I was wondering if we were going to see a scene from King Fu….
@smithsmith22894 ай бұрын
Poor guy sounds like Biden... but he can actually make whole sentences without slurring his sentences! Lmao! 😅
@frickinda4 ай бұрын
Awesome info thank you for sharing
@zoomzilla674 ай бұрын
I have a 1500 with dual climate control and it doesn’t have these bulbs. It has the grain of wheat bulbs. I’m still going to try to solder them in
@footclutchevo4 ай бұрын
Don't usually comment on this kind of stuff but have to on this one. The main shaft race, inner primary and clutch bearings are not even in play when you rotate the back wheel. That sound you indicated was more likely in the final drive system, maybe a bad wheel bearing, or possibly the transmission output main bearing. Or as simple as the belt rubbing on something... K
@togodbetheglory97254 ай бұрын
What was the singtoms why did you change it?
@badmatt42274 ай бұрын
I remember it was a code.
@hejakma46824 ай бұрын
This is a real pain in the ass without a lifting plattform.. I managed to change the right side. Happily the clacking has gone. But the left side diddn't work. I turned the screw round 🤔
@Onward4415 ай бұрын
Best one of these videos on this topic!
@vincentconte60285 ай бұрын
No front depth gauge needed with the set tool
@BudDukes-pc8dk5 ай бұрын
This is different noise I got I only hear a clunk when I let off gas in first gear bad other gears not so bad of noise.
@The.ricosuav5 ай бұрын
Where can I get those Angeled feeler gauge?
@spencersgarage5 ай бұрын
The crank pulley torque spec is 92 ft lbs. NOT 30 ft lbs.
@badmatt42275 ай бұрын
Is this at 13:27 Is the 92 ft/lbs an alternative the additional 60 degrees?
@TheCaperfish5 ай бұрын
always put the top stud back in before putting cover back on and use it to guide you on , then ya don't have to rotate cover any to find bolt holes and mess up yer RTV , it will be lined up perfectly with all bolt holes
@ozzmanmetal11146 ай бұрын
Tabajar con Ozzy lo mejor, saludos desde México
@williejeans7 ай бұрын
You just made my night
@otrstreams69357 ай бұрын
Dont listen to em, Matt! Great vid!!!! I felt inspired!!
@jacobhomstead90367 ай бұрын
Hahahaha why do I feel like I’m sitting in the waiting area to be seated for a hibachi grille?!
@powerwashking22188 ай бұрын
Graphics and music is shi*t just do a video without
@nickkiosk55138 ай бұрын
what the fuck is this music lol
@Zeek3148 ай бұрын
2:42 which connector was that?
@badmatt42278 ай бұрын
Throttle Motor Connector.
@Zeek3148 ай бұрын
@@badmatt4227 much appreciated
@jafinjohn73678 ай бұрын
Temp sensor had been there for the past 20 years.
@jeanchamplot8 ай бұрын
Buddy, unless you are out of touch or simply ignorant, YOU DO NOT USE AN IMPACT TOOL EITHER ON THE COMPENSATOR SPROCKET NUT/BOLT OR THE CLUTCH HUB NUT 1 you will loosen the magnets inside the rotor and 2 you are taking a chance at getting the crankshaft out of round..,
@badmatt42278 ай бұрын
So, instead of wanting to be helpful. You take pompous arrogant douche approach and go straight criticizing others. Which is indicative of a leftist approach to communication. I hope you don’t have children. Scroll down and you will see that “Alanmiller366” has already made similar comment. Try to mimic his style. Skip the childish insults and go straight the information.
@johncasor96984 ай бұрын
@@badmatt4227 WOW... such a nice reply to your viewers...
@isaiasbalbuena63568 ай бұрын
Everything is cool, but the dam music !!!!😡😡😡
@badmatt42278 ай бұрын
True, I have been working on improving my quality. I need to find some background music to use as background filler that is not copy righted.