Why did you hide the stain color

I’ve spent the last month stuck on my crib build because I couldn’t properly and didn’t have the knowledge of something as simple as using a round over bit. I could do all the other work but I’ve been dreading over this part to finish it in time for my child. This was so simple and easy to follow and has lifted a giant weight off my shoulders. Thank you very much.

Seems very slow. If I had a mitre saw I would just put a stop block and butt up then cut.

Check out the scoop on Binance CEO's exclusive interview for the inside track on future developments

Just wood glue works better and takes a knock.

On the miter saw, why bother with the "auxiliary fence"? Why not just clamp your stop to the saw's fence?

Which gel stain color is that?

that's a great video.. I am just finding it..

This would be good if we could actually tell which direction your finger was rotating

I watched another video that said doing the pocket holes that way is a no no. i.e. the way they described this being done would have the pocket holes on top of the shelf so the screws go down. Whereas, the way you do it is with the screws pointing up. Here's the video for reference: kzfaq.info/get/bejne/o9x_ad2SrruzYWw.htmlsi=GYOEn5e61OC5NWTH&t=402

What was the degrees setting on that pocket jib? And what size drill bit did you use and what size and type screws? Thanks.

I think those are the ones that can be used to actually take out more wood than demonstrated and then use a plug cutter (usually there is a corresponding one) on a scrap bit of wood to then fill the gap with. If using just to make the screw flush, for example on floorboards underneath carpet, a countersink with a drill bit is perhaps overkill.

Almost thought I need to drill a hole at the corner before watching your video😅

As a total beginner, I say: well done, and a lot of thank you!

Can you turn the music up so I can not hear you?

Thank you, that's a great explanation, I'd seen the right hand direction thing before but crucially they never mentioned having your thumb over the board! That makes all the difference and now that's something that I'll always remember and use 👍

Could have just said move it from left to right instead of this convoluted explanation 😂

Thank you for giving us the finger, technique.

Thumbs down! The title is misleading.

How well would this work with particle board edges? Or is something stronger like Bondo a better choice?

awesome. just what I need!

Probably the most confusing and pointless video on the internet.

Pretty disappointing. I was hoping you'd demonstrate how to do a gang cut with at least ten of those boards side by side. It's not obvious how you would clamp all the boards together when they're say 1.5 metres wide in total.

Thank you! This was exactly what I needed.

YES!!!!

A useful video but please ditch the annoying musak.

thanks

You've still botched the explanation, and frankly I haven't seen a single person explain it correctly. There is no way to move "against the rotation of the bit." The bit is circular and rotates in circular fashion, so that is pointless guidance and really explains nothing. Also, in your video when you say "the bit's rotating this way," we can barely see your hand and have no idea what you're doing with your fingers. Looks like you're swirling them in the same direction you're pushing the router. Which is the opposite of what you say to do.

WOw! Finally, I know! LOL. (What the heck took me so long?) Thank you, BuildSomething!

FINALLY...a way to know what I am supposed to do in plain english!!! Thanks!

Thankyou for clearing this up. I had never known exactly which direction to cut until now. Many blessings to you.

This video helped me get my saw back to cutting straight. I would comment that you have to watch the entire video to figure out how to perform the fixes if you find somthing out of alighment. It would be a better video if you showed how to check alignment of one thing then immediately after how to fix it. You also say to loosen the three screws for one of the fixes, but I would have found this step helpful to be videoed. I felt I had to remove all three to dust out all the wood shavings and then wasn't quite sure how to go about getting them back in and aligned, but I managed!

Can you stain spackle?

Simple and informative. Thank you.

Thank you for your simple explanation without all the unnecessary talking. I now understand what these are for.

Great Tip!

For those screws he should have used a countersink bit with a regular drill bit ie: not tapered.

Omw, that’s ingenious!

Wish you showed going around a corner

That was so awesome in the simplicity of right thumb over the board index finger pointing the right direction Thank you so much The video I've been looking for ✌️

This was a very helpful tip. Thank you.

What? Speak english

I want to cut strips

I stopped buying expensive plywoods altogether ... I have built beautiful shelving and edging using thick utility grade plywood and buckets of drywall mud. Works like a charm. Little extra work to save 100's of dollars on plywood. Sand, prime and paint. Looks just like in the rich folks houses !!! LOL

I made one with stroller wheels that I found in the trash. Works excellent, every time I see an abandoned stroller my eyes grow.

What kind of wood is that?

Simple rules and clear explanations…thank you so much and have a nice day!

Can use this method for shaker style closet doors? 7ft long x 10in wide?

From left to right.

Whats keeping the round over bit from digging in deep in certain spots? Been trying it out and everytime i have some deep cuts in the edge. Do i need to use a special guide to make sure the bit stays in a straight line?