Thank you for your sharing. What model is the vehicle and how many km(mil) does it have?
@hamadakhmechanic65262 ай бұрын
Hello It's Ford focus 1.0 ecoboost engine 2015 , has 90 000 km .
@avimrizani2 ай бұрын
Is that normal? When the engine is first started, a rough noise is heard along with the oil indicator light turning on. Because I experience the same thing during a cold start. a rough engine noise along with the oil indicator light turning on, and then when the oil indicator turns off, the rough noise disappears.
@hamadakhmechanic65262 ай бұрын
May be the oil pump strainer is blocked
@dado500Ай бұрын
Očigledno je normalno. Imam isti problem i ovdje je isto tako makar je pumpa očišćena. Poslušaj kod paljenja na kraju klipa
@mokhtarbachir36012 ай бұрын
Hello, what are the torque specs you used for the piston rods bearings an krankshaft bearings. New bolts or not ? Thanks
@hamadakhmechanic65262 ай бұрын
I didn't use torque because I didn't find the specs
@nigelmitchell3512 ай бұрын
I think id have cleaned and double checked the clipped pipe connector thoroughly for leaks before fitting ?
@phoenix2High3 ай бұрын
خيي كيف ما ارتخى معك شداد الجنزير ؟
@hamadakhmechanic65263 ай бұрын
بما انه الجنزير مثبت ع الاطراف ما بيتحرك الدفاش بس مو لازم تبرم المحرك ب هيك حالة
@danielfl.93474 ай бұрын
What happened to the piston since it broke?! I have the same engine. I use 0W/30 and change Oil every 10.000km. Is it ok?
@hamadakhmechanic65264 ай бұрын
It's a common problem on this engine 1,4 tsi because of the high compression produced of the turbo and the compressor .
@danielfl.93474 ай бұрын
@@hamadakhmechanic6526 Thanks. Any way to avoid it?? So expensive to repair :(
@hamadakhmechanic65264 ай бұрын
Hi repair costs depend on workshop and parts price, to avoid damage is better to change oil regularly to keep the viscosity which protects the parts under friction
@danielfl.93474 ай бұрын
@@hamadakhmechanic6526 ok thanks so is 0W/30 ok? VW says to use this but some mechanical says to use thicker Oil
@thealgerianwarrior875 ай бұрын
السلام عليكم اخي هل يمكنك ان تفيدني حول موضوع حساس ضغط الزيت في نفس هذا المحرك حيث تظهر علامة الزيت بالاحمر و تختفي ؟
@user-bx7fq9vz6c5 ай бұрын
الله يعطيك ألف عافية أخي .. ممكن تفيدني شو المشاكل الي ممكن تصير معي لما يصير عندي مشكلة بالسلندر لحتى هيك يكون الحل ؟ لانو عندي نفس الماتور وصار معي مشكلة ومبين بالفحص انو فيه مشكلة بالسلندر رقم 1، ولكن كل ميكانيكي بيشخص تشخيص مختلف، واخد بيحكيلي مشكلة بالجنزير وواحد بيحكيلي مشكلة بالكرنك وهكذا !! وشو اجمالي التكلفة تقريبا ؟
@hamadakhmechanic65265 ай бұрын
الله يعافيك معلم حسب العطل شو عم بيصير ضو المحرك شغال فيها تقطيع صعوبة ب الدوران كل عطل و ايلو حل التكلفه حسب الشغل و القطع اللي لازم تتغير
@farsfars19715 ай бұрын
@@hamadakhmechanic6526 مرحبا اخي عندي مشكلة في ضغط المحرك نفس العندك في الفيديو Motor Drehzahl maximal4000
@farsfars19715 ай бұрын
شنو الحل او ما هيه المشكله
@hamadakhmechanic65265 ай бұрын
@@farsfars1971 اهلا اخي و الله في عدة اسباب حسب شو عم بيصير معك مشكلة ب ضغط الزيت او ضغط البستونات
@hamadakhmechanic65265 ай бұрын
إذا ب ضغط المحرك بيكون في مشكلة ب البستونات فيه كسر او تشحيط
@mzr46156 ай бұрын
Did you change the oil pump belt as well?
@hamadakhmechanic65266 ай бұрын
You should change it.
@ricardoiseckson53546 ай бұрын
Hi great video .can you share the crankshaft torque ?
حكيني 0736974283 بس اول شي ابعتلي رسالة و اسم حضرتك انا بتصل فيك
@dvddvd10589 ай бұрын
أخي العزيز انت وين كراجك ممكن العنوان. عندي سيارة بدي اجيبها
@dvddvd10589 ай бұрын
أخي العزيز انت وين الكراج تبعك ؟ ممكن اجيبلك سيارتي؟
@hamadakhmechanic65269 ай бұрын
ب اي مدينة موجود انت
@dvddvd10589 ай бұрын
مالمو. وانت؟
@hamadakhmechanic65269 ай бұрын
انا ب kristianstad
@dvddvd10588 ай бұрын
@@hamadakhmechanic6526 ممكن رقمك لو سمحت أو عنوان الكراج
@hamadakhmechanic65268 ай бұрын
0736974283 اخي هي رقمي ابعتلي رسالة اول شي
@mohammednasarat73289 ай бұрын
What is the torque?
@user-gm9xd6kj5n9 ай бұрын
Merci
@petermckay52849 ай бұрын
My focus 1.0 ecoboost I plugged my other diagnostics scanner in and it says this fault is Power supply fuel pump Short circuit to positive or open Intermittent I ordered a low pressure fuel pump that will sort it i can start the car and rev it up but when let it idle car just dies and if i rev it it will stay running for a couple of minutes with accelerator keot pushed down a bit thanks for your info mate
@MX-CO10 ай бұрын
Was this the problem?
@hamadakhmechanic652610 ай бұрын
My friend drove The car about 5 months and it was good. I have cleaned the intake manifold, no parts change.
@TocyBlox2 ай бұрын
@@hamadakhmechanic6526 yeah thats def a head gasket failure. Engine is on borrowed time. Get that gasket changed man.
@dvddvd105811 ай бұрын
السلام عليكم معلم. هذا المحرك بيعوج صبابات اذا انقطع الجنزير اثناء القيادة ولا ما بيعوج ؟؟ تحياتي
@hamadakhmechanic652611 ай бұрын
و عليكم السلام اخي اغلب الاحيان بيعوج صبابات
@dosal31011 ай бұрын
Any updates
@discusion982111 ай бұрын
How do I translate this video in English
@cristi-qv1nz11 ай бұрын
Thank you. I have a diagnostic after 180 000 km. p 1445 , peugeot 207 2010 1.4 hdi. This tank exist on my model car?
@jalalshahin8456 Жыл бұрын
فناااااااان
@a7madcode Жыл бұрын
Very good explanation 😁
@M.V630 Жыл бұрын
التوربو شغال مافيه شي بس فك مضخة الهواء و نضف المصفاية تبعها لان شكلو علقان فيها بقايا قشاط الصدر
@M.V630 Жыл бұрын
السلام عليكم ياريت لو عندك رقم جوال حاكيك صوت عالواتس انا بألمانيا وعندي مشكلة بنفس هاد المحرك السيارة وهي واقفة عم يرج المحرك و بس تمشي مافيها شي مأحلاها فحصنا الضغط تبع البستون طلع تمام المكانيكي حطلي زيت غلط و قشاط الصدر تفتت بالسيارة هاد يلي خلانا نفتحر المحرك و صارت مكلفتني 2700 يورو وما تصلحت
@Armankhan-ri1rs Жыл бұрын
hlo sir today i also change this pouch for my car citron c3 hdi cuz its show clogging risk filter but i dont know the problrm is this or other problem
@hamadakhmechanic6526 Жыл бұрын
Hello friend You should make a diagnose with scanner
@kujtimaliji4345 Жыл бұрын
Grymt bra jobbat, har precis öppnat en motor 1.4 tsi CAVD efter att kedjan kuggat ska byta kolvar, ventiler osv. Har du kanske tillgång till ritningar? Tack på förhand.
@hamadakhmechanic6526 Жыл бұрын
Du får kolla ventilerna om dem krökt. Kolvarna behöver inte att bytas om det fanns inga spricka.
@kujtimaliji4345 Жыл бұрын
2 av kolvarna hade spruckit, så jag byter alla 4 samt alla ventiler. Hade du ritningar du kan dela med dig? Kan vi höras kanske på telefon?
@hamadakhmechanic6526 Жыл бұрын
Vad du menar ritningar
@snoopy81 Жыл бұрын
Well done explain, keep it up.
@maringlen7861 Жыл бұрын
I replacled it in a car servive center but the light want go away even when they reset it through a computer. Any clue how to solve the dpf light problem?
@hamadakhmechanic6526 Жыл бұрын
What is the fault code, which light on
@micasb9 ай бұрын
Hi. I have the same problem. Were you able to solve it? The additive bag was replaced, but the lights never went away.They're exactly the same as in the beginning of the video (minute 0:08)
@user-xl9re3pu5g Жыл бұрын
سيد المعلمين
@ThePahan007 Жыл бұрын
what milegae has this car at the moment of this video? what type of oil was used during the years in this engine?
@DaDaDo661 Жыл бұрын
You got lucky
@a7madcode Жыл бұрын
🎉وأخيراً
@prophet1o158 Жыл бұрын
Where can a new additive pouch be purchased from and what are the average price ranges for one? Also does the additive pump have to be replaced and how would a broken pump be diagnosed?
@user-yl5ip8sl4j Жыл бұрын
الغالي بغيت اسم الورشة عندي نفس الموضوع في سيارتي
@afifhasbullah7135 Жыл бұрын
Do u have video on how to do the oil engine change for this?
@LittleBatteler Жыл бұрын
ٱلسَّلَامُ عَلَيْكُمْ
@hamadakhmechanic6526 Жыл бұрын
و عليكم السلام
@oskarflyman3064 Жыл бұрын
Hur mycket ska man dra ventilkåpan?
@hamadakhmechanic6526 Жыл бұрын
Tightening torque: 10 Nm + 1/4 turn (90 °) further
@Ghost-vn9pv Жыл бұрын
Can you drive the vehicle still with that liquid empty?
@hamadakhmechanic6526 Жыл бұрын
It Will go on limp mode
@retugfdufd2997 Жыл бұрын
هل يمكن الغاء مصافي أعمدة التوازن وماذا يحصل اذا الغيتها؟
@SALOPARISIENNE-gt4on Жыл бұрын
Ford Big cheat
@mogomega8825 Жыл бұрын
Hej Hamadakh, Väldigt bra video 👍 Du nämnde aldrig vilken moment drog du åt bultarna till topplocket? Tacksam för svar .
@hamadakhmechanic6526 Жыл бұрын
Tack så mycket Man ska dra bultarna 30NM först sedan drar dem 90 grader på 3 gånger.
@mogomega8825 Жыл бұрын
Tack för ditt svar, om jag förstår rätt så du menar 90 grader på alla efter 30NM och sedan en omgång till med 90 grd för alla och slutligen en sista 90grd ?
@hamadakhmechanic6526 Жыл бұрын
@@mogomega8825 korrekt 👍
@mogomega8825 Жыл бұрын
Härligt Hamada! , du verkar kunna dom motorarna 👍 Undrar vilken moment ska jag dra pullyn till veven?
@hamadakhmechanic6526 Жыл бұрын
@@mogomega8825 hej kompis Vevaxel bolt ska spännas 150NM och sedan 180°
@phumlane5981 Жыл бұрын
Hi brother I need you help as I get same notification when I try accelerating Nd my main seal oil is leaking Nd cam has play
@Sugarkryptonite Жыл бұрын
Hi nice video. Can you say what was wrong with the original oil pump?
@hamadakhmechanic6526 Жыл бұрын
Hello friend first i thought there was a low pressure on oil pump, but i discovered then there was a damage on non return oil valve on cylinder head