3 ай бұрын
Пікірлер
@Andersonbitencourt-gr5bb 6 ай бұрын
Boa noite tô instalando um painel desse tá dando touble 0 poderia me ajudar por favor
@liminalreality9617 Жыл бұрын
1:05 a WHAT CHAMBER
@ABrugal 2 жыл бұрын
how to avoid the water discharge and test the smoke or any fire device like water flow or smoke detector. thanks
@KennyMFJones Жыл бұрын
Shut the main control valve off, open the drain, test your smokes. Once the smoke clears, reset the panel to clear the alarm, the priming line will reset and you can then open the main control valve and shut the drain.
@robottron7289 3 жыл бұрын
When is the best time to turn off the fire pump when a sprinkler goes off?
@dannyw7662 3 жыл бұрын
Be nice if the control box was not blocking the view.
@user-sy7et2nh5s 3 жыл бұрын
how to use the module CA2Z class A correctly?
@dwhallon21 3 жыл бұрын
I have reset a viking dry valve 3 times. And everytime after an hour or so we have gone back to having water in the lines. I have cleaned brass face and rubber on flapper. Flapper plate appears locked down yet it goes wet after about an hour.
@mackregis7552 3 жыл бұрын
Hard work and dedication surely pays off at some point. Well done Mr.James.
@aymanbiomy4756 3 жыл бұрын
Is it mandatory in nfpa? Where is the best position to install is it in pump room or outside it? Is the only propose of it to get alarm sound?
@raulvasquez3298 4 жыл бұрын
Thank you for the information
@jaygdad 4 жыл бұрын
Doesnt fit in a 3 1/2” Stud wall. 1/16 of wiggle with the escutcheon. Terrible design.
@richardraab698 4 жыл бұрын
No volume
@gmichalowicz 4 жыл бұрын
Why doesn't bracket come in 1"?
@marcomarvil5788 4 жыл бұрын
Thank you, which is the replacement gasket code of the clapet and cover for the 4 "dry valve model f-1 part 08841. best regards. Maco
@FireAlert 4 жыл бұрын
how do you find lost password?
@mechtrotip5034 4 жыл бұрын
But why is mechanical alarm required When we have detectors connected to alarms
@saturninojrplumbingfirepro0413 4 жыл бұрын
Nice presentation..
@sheldondrake8935 5 жыл бұрын
an exceptional animation, shows finesse that's rare in these
@jiromartinez3301 5 жыл бұрын
Can i use this system in a non-ulfm pump should i buy a ulfm controller my client needs that kind of system
@palmontaj 5 жыл бұрын
👍
@313thqkd 5 жыл бұрын
밸브가 기동 된 후 복구시킬 때 몸체의 커버를 열고 클램프와 리치를 조작하는 것은 매우 불편한 일입니다. 그 부분의 기술적 연구를 통해 커버를 열지 않고서도 세팅 할 수 있는 제품을 출시하면 좋겠네요.
@rainbowisnotemo 5 жыл бұрын
zeria
@RahulKumar-fk9yp 6 жыл бұрын
Hindi me banayea video
@ad8keez 6 жыл бұрын
Hey cameraman, next time pick an angle that doesn't involve your reflection...
@patriciaschneider3677 6 жыл бұрын
Great looking facility. Looks like a collaborative environment.
@mshahbaz4948 7 жыл бұрын
s
@mandeepsandhu8614 7 жыл бұрын
nice n powerful system
@mallrat11 7 жыл бұрын
hmmm, ive never seen those clips before. they look incredibly useful for a tight spot like that when you need to run the pipe all the way at the back of the stud
@vanthanhnguyen5384 7 жыл бұрын
Could you tell me about Pre-Action Valve of Shilla ? Thanks
@dathuynh8704 5 жыл бұрын
What is Shilla?
@vinceb9310 7 жыл бұрын
Prime??
@hummerdance1008 7 жыл бұрын
NICE TECH VIDEO
@aljonsumayang2025 7 жыл бұрын
good
@frankrogan5111 8 жыл бұрын
I noticed you did not close the pilot line ever. Is there a reason for it? I've heard of the valve premature tripping because the solenoid did not reset properly if you don't run water thru it while resetting the the panel via solenoid.
@danmacdonald2797 8 жыл бұрын
would be nice if you told how to adjust to allow pressure into device after repairing parts.
@Vikingsprinkler 8 жыл бұрын
+Dan MacDonald Thanks for the feedback, Dan. We'll keep that in mind for future videos.
@jesse977 9 жыл бұрын
Good video
@ToaKingz 9 жыл бұрын
That wasn't that bad.
@mohamedgaber1462 9 жыл бұрын
Dear Mr. Martin, we install this valve and the client want to operate the deluge valve using an electrical " manual release call point " connected to the control panel - is this possible ?
@Leonardomachadotst 10 жыл бұрын
Amazing !! O_O
@vikramrio 10 жыл бұрын
Awesome. Simple and to the point. Thank you.
@danielsantos-kq8sf 10 жыл бұрын
Wow ! Good job guys !!!!!
@jamesredmond7360 11 жыл бұрын
A main drain test "drain drop" should be performed anytime the control valve has been closed to ensure control valve is fully open and proper flow. Same reason we flow test hydrants to check for obstructions in the water supply. Residual supply pressure should usually not exceed 10 psi drop when 2" main drain is fully open.
@Fnix 11 жыл бұрын
Correct. It is neccesary to take care when operating these
@rapidfiredm 11 жыл бұрын
Vics stick often just my opinion did 5 today 1 didnt open 5 yrs old
@DawnOfTheDead991 11 жыл бұрын
So one alarm would cause all the sprinklers to spray out water? That sounds like a recipe for disaster
@TheCarson116 3 жыл бұрын
These kinds of systems are only used in high-risk buildings, such as a facility that handles flammable or explosive substances.
@ronniecharlton2280 3 жыл бұрын
Often used as a cool down in industrial applications. Examples large tanks of flammable liquids. The Classic Deluge was installed in theatres where the fire would be stopped with a wall of water at the Proscenium (exempt from full flow testing). A form of Deluge is often used in Aircraft hangers but has mostly been replaced with deluge foam apparatus... All deluge types have to be tested NFPA25 and are located in areas that can handle the volume of water produced by them...
@JRCOZY 11 жыл бұрын
forgot anti flood valve..
@moparedtn 7 жыл бұрын
The anti-flood device under the accelerator automatically drains on the Viking.
@98296 11 жыл бұрын
Forgot to drain low points
@potmanaw 11 жыл бұрын
thanks for saving me some money!!!!!!!
@king65462 12 жыл бұрын
to much work for 1 system
@minonuno3041 Жыл бұрын
It looks scary with all them pipes but they're easy once you work on them a couple of times
@Vikingsprinkler 12 жыл бұрын
In the United States an Excess Pressure Pump is not used in the trim, and the gauges will show the same pressure at the time of set-up. If the Water supply is a variable supply, once the pressure increases the top gauge will show the highest pressure that the system has been exposed to, while the lower gauge will show the current pressure.
@ahmednagi8583 5 жыл бұрын
i need 7 pice please contact number or supplier in saudi arabia
@CaptainDaccat 12 жыл бұрын
These are good videos I don't do much service & repair anymore, but it's always good to stay updated if the time may come again.