I purchased and downloaded these plans and the instructions did not download. When I try to download again I receive an error that download has been exceeded. I have reached out through the contact. How long to get a response on getting the full download?
@sanjeevmidha851123 күн бұрын
Wow very nice
@suelloasoy2466Ай бұрын
Ive tried ur concept. one grinding blade can cut about 40 bottles the longer u use the more bottle will be brocken the blade will no longer sharp and its hard to find the alinement
@emmanuelmutheki72642 ай бұрын
How much
@venanciofragoza14393 ай бұрын
Hello from north dakota!! I come to mesa every January visit my inlaws!! I'm saving video and gonna give these a try
@coleyryan675 ай бұрын
Where can I get plans to make this please
@seanbrotherton5426 ай бұрын
Immediately following this video Johnny was killed by his wife with a small mink paintbrush 🖌 😂 I really like your choice of materials. I use the same fence pickets as mounting boards for mailbox post builds. You've given me some good ideas. And my wife and I LOVE hatch chilies! Let us know how they come out!
@whatsnewjohnny35126 ай бұрын
My wife rewarded me for my good work and keeping her mink brush soft.
@jamescolton67766 ай бұрын
I downloaded plans for Leroy the sanding un it. Question in regards to the clamp where the vacuum attaches. Where did you find it and what is the clamp called.
@fillmore2006 ай бұрын
Jhonny, Have you done something to slow down the speed of the angle grinder ? I tried this , but the bottle just heats up and cracks.
@whatsnewjohnny35123 ай бұрын
Good morning are you using the thin diamond blade?
@JohnArdizzone786 ай бұрын
Nice work and I do like the finished product. I could really do without the scrolling text though. I’d rather see what you’re doing and hear what you have to say about each step.
@jameswalsh40567 ай бұрын
Nice design - appreciate your vid. I like to use tape along the inside of each side piece right along the shoulder line, if you will, of the box (or dovetail) joint. That way any glue ooze is more easily removed after box is glued together. I look forward to building a couple of these.
@hillcountrygarage7 ай бұрын
That was very interesting. Where did you get that router table top jig you use? I need to pick one of those up! Not the jig for the finger joints, but the one for rounding the corners.
@Mike-ou5ps7 ай бұрын
Ok...I've had to stop the video. I just can't watch it any further 1/4th into it. Have you ever watched a movie that had subtitles? Annoying, right? Now, imagine that and then every single time subtitles appeared, the movie stopped playing. That's REALLY frustrating. My advice to you Sir is to STOP with the subtitles altogether. Just do your build and discuss verbally as you're working. I'm sorry Sir,...your boxes on the picture looked cool, but honestly, your video sucked. Thumbs down.
@websterbehrens78378 ай бұрын
Great video. Is that a Rockler box jig ?
@patwaldrip37748 ай бұрын
Great looking cedar boxes, nice craftsmanship. How much do you sell them for in your area?
@AndrewR748 ай бұрын
Thanks for sharing. Those are really good.
@jameswalsh40568 ай бұрын
Nice looking box. Please use a router sled of some kind Brother.
@federicocaldera60528 ай бұрын
ser carpintero o artesano es una pasion.... 👋👍
@VIPER35GP8 ай бұрын
Loved the video, thank you for sharing.
@robertsmith35188 ай бұрын
Nice video ! So many folks are not speaking in the videos ,just playing crappy music . Your presentation hit the spot . Thanks for the time ! Cheers
@user-uh5df5xy4h8 ай бұрын
Cedar is 106 for four fence boards
@whatsnewjohnny35128 ай бұрын
At Home Depot Cedar Fence boards are $3.97 they are marked as 5/8" x 5 1/2 -6' They need to be planed and then stored flat with weights.. Where do you get yours? Thanks Johnny
@greggordon62158 ай бұрын
$3.97 for me in NC too. I love using the cedar fence boards!
@user-uh5df5xy4h8 ай бұрын
I mostly use eastern red cedar.
@matthewloeffler58468 ай бұрын
Make a list marble box for your friend. Marbles in it but don’t cut a lid. 😂
@whatsnewjohnny35127 ай бұрын
funny
@cabman868 ай бұрын
I have that same table saw. It's powerful too!
@cabman868 ай бұрын
Every time I go to Harbor Freight I buy a few clamps to add to my collection. I have about 60 now.
@cabman868 ай бұрын
These are great! I've been making these for a few years now. I cut fallen tree limbs into boards to make them.
@MASI_forging8 ай бұрын
Great work dude 👏👏
@bigjoe89228 ай бұрын
Great job thank you for the video
@dgperforms18 ай бұрын
I fast forwarded through a bunch of gluing....
@johnthompson34628 ай бұрын
They look great Just one point.I have been woodworking for over 50 yrs. Never put glue on both pieces and same with fingers and never had a failure. The two sided glue idea is from the manufacturers to get you yo use more glue
@whatsnewjohnny35128 ай бұрын
Glue also helps fill in small gaps. Glue is cheap. Waite untill Jan 10 and see whats next. Thank Yoy for your comment
@allenhuckabee37648 ай бұрын
That’s an interesting comment. I have always put glue on both sides…you mean I don’t have too…sure will save me $$
@johnthompson34628 ай бұрын
@@allenhuckabee3764 Hi,Yes it is true( for all my project for sure) but there is also quite a few of the big makers out there that have done tests and had the same result. Same with clamping.See too many wood shows where they use a dozen clamps and tighten them so much they push all the glue out. On small boxes you can use just tape. Lee Valley sell a tape,that looks like masking tape but has a little stretch to it and works great.I have even told some makers and had thanks from them
@tomspallone18687 ай бұрын
@@johnthompson3462Probably was derived from the proper use of CONTACT glue where both pieces should glued and semi dried before joining.
@thomaschandler48317 ай бұрын
Yea I only glue one side as well .. however… my circumferences are tight
@robertduley54468 ай бұрын
Wow just chopping the top excellent idea, no measuring for the top lid
@marks.28148 ай бұрын
Enjoyed the video, thanks
@FreiheitGalleries8 ай бұрын
I can see your passion. Great Job! Keep up the good work!
@user-jt2rm9cp5r9 ай бұрын
Oh and be sure to put a patent on this!!!
@user-jt2rm9cp5r9 ай бұрын
Wow Doc Brown has nothing on you! Out of my skill set but this is brilliant!
@Howardtripper9 ай бұрын
What discs do you use
@getbuckb4u9 ай бұрын
My great uncle used to use a table grinder to cut 7up bottles back in the 70s/80s so to me this is overkill. Nice set up but overkill
@wagnerdesigner9 ай бұрын
Very good.. congratulations
@harmvandergugten270410 ай бұрын
Wow! love it, I don't see an adjustment for the thickness of the bottle. Am I missing this?
@loveedaniee11 ай бұрын
I wish I could buy this!
@bonefish93511 ай бұрын
great job Johnny, I also cut bottles to make glasses and built a wooden jig that's less complex than your device. The main issue isn't cutting the bottles, but how you do it and in particular what angle grinder you use. I noticed that the discs you are using are green and probably the same band I am using. I bought them from a Chinese supplier I found on pinterest, but apparently, there are many that sell the same discs at different prices. The discs I am using are 100mm in diameter wide and have an inner hole of 20mm. Now, all angle grinders I found on the market are intended to be used with standard discs of different diameters, but all with an inner hole of 22mm. It's been mission-impossible to find a device with such a size. I noticed that you are using a Makita. Can you tell me what model is it? thanks
@praphakaran201211 ай бұрын
good idea thanks
@a.caution.hairy.tail. Жыл бұрын
You are a genius
@whatsnewjohnny3512 Жыл бұрын
Thank you FYI I just completed a square bottle cutter that is mounted on the end of the cart. It is working great. Ill do a video on this in September 1. Text me at 4802509427 Thanks
@mthandlebar8160 Жыл бұрын
Does anyone here have the original design files for this setup. I ordered the newest file and am unable to open it up I'm having issues finding the right brackets for the casters and pulley. I contacted Johnny yet I have not gotten any response from him
@Harrell423 Жыл бұрын
How well do you like the green glass cutting wheel? Is it worth it?
@johnkifanga6194 Жыл бұрын
Wow
@Happydays147 Жыл бұрын
Would you consider building another and selling it..
@Happydays147 Жыл бұрын
Wow, I'm a beginner bottle cutter and I've used about everything out there, nothing is all that good, BUT I'm in love with your homemade machine, I definitely want to make me one for sure..damn I wish I could buy it. I need one now
@smarleyjoe3569 Жыл бұрын
Nice it looks like you can adjust enough to cut hte top out instead of the bottom? Maybe it can also be a tumbler to clean the INSIDE of bottles.