Hey there. At the moment I’m far too busy at work to take on any side jobs. I may have some time in a month or so. What did you need done?

Yamaha if you want reliable

@@HubertGarand-hf7rh Really wish I seen more people putting the SVHO in, seems like that motor isnt working near as hard as the rotax to perform at that level

I went with a 2012 seadoo RXTX 260 hp

@@worchest2039this was all in eco mode on the rotax 260 hp. In sport mode it feels like double the hp

Northern California

Jetstream is in Delta BC Canada and ships all over

I’m in Mission BC Canada. I wish I could get out there. Unfortunately it’s pretty far for me

No doubt. That sounds like a beauty day. I’d totally weld up a couple boats for ya.

Thanks man. For the sound deadening I used this egg Carton shaped foam from Amazon. It made a big difference it comes in a vacuum sealed pack so you have to submerge it in water and ply with it for a bit then it will take its original shape after you ring it out. And I used 3m double sided tape and it’s not going anywhere. www.amazon.ca/gp/aw/d/B0957CPDCG?psc=1&ref=ppx_pop_mob_b_asin_image

Thank you. No. This wasStave lake in mission BC Canada

@@dimesdailymetalcraftddmc8461 oh i see right on. Nice place!

If it wasn’t for the bench seat, I’d think that was my boat

Damn brotha. Glad I can help. Any questions just ask

My pleasure. My future builds/ projects will up for viewing. Thank you🙌

Thanks man. I really appreciate the compliments

Thanks brotha

I did not. Not much room after the chine guards

Hey mike. As of now I’ve build a couple boats for myself. This one is my 2nd. Sold the first. I’ve also saved a few others from previous hack job builders. I’d be into building a full boat for someone but I’m not set up to have the boat coast guard compliant and all that. There’s a lot of headache that goes along with it. Where abouts are you located

@@dimesdailymetalcraftddmc8461 You definitely do great work sir. I'm located in North Carolina

Thanks again. Yeah unfortunately I don’t know what it would take to get it there. I know just to get one into the states from Canada you have to provide the epa information on the motor and I belive anything older then 2010/1212 doesn’t comply with USA emissions standards anymore so they won’t let it in. That’s seadoo anyway

Haha. You totally could. I’m only in mission. When you get her done let’s go rip it up

Thank you 🤘

It’s Stave lake in British Columbia Canada about an hour west of Vancouver

@@dimesdailymetalcraftddmc8461 I go jet boating in the Missouri Ozarks.

Omg that’s awesome. Never even knew that place existed till the show came out. It looks amazing there.

@@dimesdailymetalcraftddmc8461 That tv show really doesn't portray how Lake of the Ozarks actually is. There are 20+ rivers In the Ozark region that people canoe and white water raft, and are fun to jet boat on, the scenery is eye candy 360°.

Omg. That’s sooo awesome. I’m jealous

Hey man that’s great. I’d give it 80-100 hours for a first go

@@dimesdailymetalcraftddmc8461 thanks!

I used a seadoo as the doner. Came from a 2012 rxtx 260. Pretty much everything comes out of the ski

Thanks man

Just bare bones hull with UHMW and steering mount ur looking at $21,000 roughly

That’s including the rear seated engine cover

Thanks man. You had them welded it for you. The last time I was in there the boats they had sitting there ready to ship looked top notch. I was impressed and the time it takes to fit and weld a hull they do offer a really good price

@@dimesdailymetalcraftddmc8461 Yeah the price was better than having it done local. Never been to their shop but the guys up there were easy to work with. Also they had it completed and shipped about a month before schedule. Their work is nice it's just your welds are close too perfection, due to it being your boat I'd say. Also the videos I have watched of yours have all had something in them I had not taken into consideration, so I appreciate that. What I've bought so far is the shell, fixed mount steering helm setup that after watching your video I want tilt🙏, shockwave suspension seat base with slide/swivel, and have heated prp seats on order. Wanting to put a Honda K24 engine with a turbo but haven't pulled the trigger yet, also haven't decided on the pump being that most stuff is coming from NZ shipping cost are stupid so trying hard to source parts closer to US. I'm goal is to be on the water in 6 months not wanting to rush through missing something because I have no clue what I'm doing but that's nothing new! Thanks again and you'll see me asking for guidance more than likely in the near future. 😉

Hey there yeah the jetstream guys are great to deal with. The forgot a couple things for boat on the pallet. I called them and the had it shipped that via rush delivery. For tilt steering you could always upgrade down the road. It’s hella expensive building these boats. I’m not sure about pumps but I know the southern jet nozzle with reverse bucket is super legit

Hey there. It’s called the tig finger. It’s designed by a guy on KZfaq. His channel is called tig time or something like that. Web site is weldingtipsandtricks.com I believe. It helps so you can rest a finger on the hot metal right next to the weld so your hand stays steadier for nicer weld profile. I have pretty shaky hands if I havnt eaten for a while I sure it all the time. It also slides across the metal very smoothly.

Thank you 🙏

Thanks for the kind words brother. Thanks for the request. I’ll definitely do a slow walk through when she’s done. cheers

Right on. So happy to hear it. 🍻

Thank you. I put them closer to the outside for when I go camping I’ll throw some gear up there to be strapped down. Just trying to maximize the space

Haha. Thanks man. My goal of this build series was to help people and to also get some work out of it. To bad we are so far away

Thanks man. I did make a little purge tube/ box for them. Worked perfectly. I’ll be uploading some of it one I get further along cheers

It’s 1/8 5052. I don’t have the boat here anymore. If it comes back and if it’s cool with the owner I can do a walk through