I searched forever for a simple way to cook chuck steaks. Thank you so much!!!!

😂

That was disappointing at the end

Thankyou for starting with the fabric intact.

I’m going out with a couple

APRIL 2024 ... you will no longer find a BUFFET in DOWNTOWN RENO - and - the one at J Resort was CLOSED for remodel. Atlantis has one ... but BUFFET 💲 PRICES are no longer a value 😢

That pond looks great. How did the inpond 600 do after a few years now? How often did you have to clean it

How do I take off the bobbin to switch thread? . You just took it off and didn't say HOW??

How is it not extremely tough?

Must get it tender 1st out of the box. That is always the key, to a good steak👉👉 Chuck Roast you only got about 45 min to get the steak flavors out of it 🥩🥩 or, it will start getting a ROAST BEEF TASTE > the way i do that is GET IT TENDERZIED 1ST, Then pat dry oil it and salt and pepper only all it need while grill, 30 min heavy smoking, Flame broil to your likeness, Pull it off let it rest cover with you other rubs you like while its resting and melting down into the meat. About 45 min. then it ready to eat

When the blood come to the surface when i flip them. come up to the top again ITS DONE FOR ME

Just bought this used without instructions...the copper plated requires no oil to plates prior to pouring batter?

Lost me at the gas grill

I inject brine into mine forst and cure in a pail in fridge for two days when done the meat in the brest is pink just like cured ham

I bought this long time ago and never used it and I'm having the same issue, it wont Stich

Just picked up for clearance $50

They look great!

Watched the video, cooked the meat. Its awesome brother! Thank you!

crudo

Thank you so much for posting this video. I had the same exact problem. I’ll be returning my hand held sewing machine!

Looks mighty good

they look beautiful.

I love mine yes its a pressure cooker mines 4yrs old..im ordering a replacement pot today ..the inside chipped away on the pot

I can see the issue with that machine, that isn't the right screw for the needle holder. I'm guessing someone over-tightened the original and stripped out the threads (no pun intended) so they replaced it with a slightly thicker screw and it's chewed out any threads left. The original screw that holds the needle is designed to be turned with just your hand. it had finger ridges. it does have a slot in it for a small flathead as well but you don't need to/shouldn't crank it that hard to make it secure. probably how the original owner stripped it out.

A really good tutorial is by Easy Sewing for Beginners. How to operate a handheld sewing machine. I hope people will watch it before sending the machine back, as it has loads of tips x

Wish I woulda seen this before I ordered it. Got it yesterday and hate it. Same problem. It’s junk. Sending mine back.

Cheap and easy😊

EVERYTHING is BETTA w/ BUTTA ‼️🤘

Mine doesn't work either. Same crap

Great job honestly man. That’s how it’s done right there buddy!!!!

Lmao!!! We are gonna spray it…. Shit! That’s me in the kitchen.

Hilarious😂

Thanks Good video

Why do you flip them when on the other side? No one will see that. And you’re opening the grill when you don’t have to.

Still recommend it’?

Beauty bird!

I started to get this, but I can see it's not stainless and it rusts badly.

Thanks for posting this. I could not figure out how to open the door to the power cord. It was hard to open, but you showed the way. Thank You!!

One year later, what is your opinion of this oven? Still worth it?

👍

I hate it. Too much of this and that. My battery case was stuck. Almost broke it to get it open. I dont see where the stitches are very sturdy.

Im going to have to try this cause peanut oil it qay too expensive these days to be frying lol

Great video! What is the CFM? Thank you

Excelente video amigo te felicito

Update on my previous comment ,1 month ago when I watched your video over and over ,pausing and rewinding for a couple of hours,,, and then I was greatful for your info , with this new knowledge I was excited to start sowing stuff....unfortunately I couldn't even get past step 3 ,, and I gave up and threw the dam thing in the cupboard, . I've kept the box so thinking of giving to my sister as a 50th birthday present😉😉 Ps you 2 are a lovely couple , thanks one again ❤

Looks delicious 😋 good job 👍🏾

How did your pond hold up from two years ago? Please let me know!

I thought it was a simple sewing machine,, didn't realise I,d need a university degree in sowing . Thanks for the video , , full gratitude and appreciation the effort you put in with your editing too

Thank you for having the only Walmart Blackstone review. How do you like it so far? Do you think someone should buy one? On the fence about buying one from Walmart since they have the least expensive 36" one.

We also have one, but the door sometimes get stuck . its hard to open.