Thank you

Excellent , thanks for sharing. Cheers.

Bump

Algorithm

Thanks for posting .Always awesome trails.

Is the damper still working well?

Don’t buy this! Tech support just told me these woofers only last a couple years, and most quit after only a couple weeks!

should've used the song Wharf Rat by the Grateful Dead. "My name is August West..."

i like this solution, gonna run one myself. thanks!

Is it any good?

Nice video, the thumb is meant to be mounted on the next pin below yours, where the arm connects to the bucket.

Anyone else have the issue where your truck has the wpt12 with no signal or power? Ive read forums and watched other videos to enable it in forscan with no success. Im about to bypass it entirely and lean on this video.

Butt splices are NOT a hack, that's exactly what you should be using on any automotive wiring. NEVER solder; the constant vibration of a vehicle will eventually cause solder joints to crack. That's why NASA uses crimp splices for spacecraft. You just need to make sure you use a proper crimper and make sure it's the right type for the splice you're using! I had to buy a different crimper for heat-shrink insulated connectors versus non-heat shrink. And always use ratcheting crimpers, they will always provide higher clamping force.

BuiltRight Industries makes a nylon loop adapter to go onto the rear seat latch. It's a must-have for every F-150 owner. Gives you a nice nylon strap which connects to a plastic piece that goes over that nub, and all held in place with a steel plate. Took me 5 minutes to install. Check them out I highly recommend.

81 FXB Sturgis

Nice video Boss thanks

That light bar is going to touch a tree real quick

Wood clothes pin works better to keep those up....

I don't understand why people run RCA's from the stereo or tap into speaker speaker wires. There's literally a wiring harnessed in the left side rear pillar. Just get your signal there and run power. It even has a remote turn on wire(blue). You just need a motorcraft wcc 1212 harness plug, Amazon 22 bucks. To use the remote turn on you have to turn it on with forscan or the Ford dealer if you don't have DC offswitch

Great video thanks for your help.

so where did you end up connecting the blue remote wire

I'm timing my 1980 shovelhead so I don't I'm not sure about the line or the circle I'm not sure if it's early 80 or late 80 but do you do anything with the advanced mechanism or just leave it alone alone ..

Hey pal. That was a great video easy to follow no messing around fixed me right up. Thanks

Best points video i've seen so far. Thanks,

I have a 2019 without the c pillar connector. About to pull the trigger on this sub. Anyone follow this to a T and ensure it works ?

How do you address correcting the difference between having diffrent point gap size from the front and rear point cam lobes? How do you makenthem both read the same gap?

Also thanks for mentioning disconnection the negative battery terminal, absolutely none of the other install videos mentioned this.

Can’t find it anywhere. None of the links work or the alternative eBay description

Excellent video. Finally got mine done today. Thank you.

“My Leg!” 😂 nah fr thank you ive been looking for the wire colors for speaker wires and refused to take the factory HU out just to tap in to it

I have the same tractor but a slightly earlier model. Would like to do this. Nice job 👍🏼

😊how much

These spacers with O ring is still available, I just got one.

An adjustable wrench ? How about a tappet wrench ? This Guy is a Hack - read the manual

What’s up man! Appreciate the video. I can’t find the page on the link in description for the gas tank bracket, could you by chance send me something similar to what you have In the video? Thanks brother, you earned yourself a sub.

Usually I see people instal the seal on the spacer and then instal onto the trans together I’m guessing with this spacer you need to install onto the trans first then the seal ?

More like this. You just saved me several hours and 3 panels worth of removal. You've earned a firm slap on the shoulder and a solid "Thanks, champ."

I picked up the same amp/sub set up and i wired it up with the factory 1212 plug, very easy. But i didnt have a way to use forscan and 1 of the 3 dealerships that i was able to actual talk to an advisor said $90 and soonest is 2 weeks out...yea screw that. Took a chance and wired it up exactly how you described with the same settings and it works PERFECTLY! thank you so much for making this video. Definitely recommend T-tap connectors for the speaker wires, pretty tight in there.

Second time I've come back to this video. Helped so much. Thanks a million!!!

What did you have to do to make that light bar fit?

Lol ig there's a reason I'm not the only one with this beast of a van getting it converted hahaha

Do you know if the Jims 2256-1 tool is still available anywhere? Their catalog has a similar looking one P/N 2256 but it is for 5 speeds.

Hellyeah! 🤘🤠

Work for a 2023 thank bro

Looks good except for the silicon on the outside of the seal. The instructions on a semi trailer wheel seal installation says "DO NOT use silicone on the outside of the wheel seal. Wheel seals and your tranny seal is basically the same.

Thank you. Actually inspiring me.

Did it leak after you put back in

Still holding up okay? Thanks for the link!😎

You’re awesome! thank you for uploading this. Took me about an hour and a half to get my Rockford p300 10t in.