jsa2001RC channel

Пікірлер

@ericchristopher9037 16 күн бұрын

G’day mate, ithese Tamiya motors have the shortest shaft. You have created an ingenious alternative that worked great, good stuff! 👍 🇦🇺

@pcka12 2 ай бұрын

Why do you need to run it in, have you renovated the engine?

@jsa2001 2 ай бұрын

Because its brand new and if you fail to run any ic engine in you get premature wear of engine components and it wont last as long. The engine has good steady revs now.

@pcka12 2 ай бұрын

@@jsa2001 that is good old engines with white metal bearings, but I assumed that your diesels must be relics?

@kuehn1953 Ай бұрын

@@pcka12 Not a "relic" although it's possible this example is NOS (New Old Stock). Progress Aero Works (PAW) is still making these in Macclesfield England.

@pcka12 2 ай бұрын

Where do you get diesel fuel these days

@jsa2001 2 ай бұрын

A few model shops sell model technics diesel fuel. Only one or two will deliver it to your door. Leeds model shop will do this.

@pcka12 2 ай бұрын

@@jsa2001 thanks

@lonestar5253 2 ай бұрын

Got a lot of crankshaft wobble. Is the front crankcase bearing any good or is this just customary with diesel engines

@jsa2001 2 ай бұрын

It's an optical illusion, no wobble there and the moulding of the prop makes it look even worse.

@user-ip8wv3hq6j 2 ай бұрын

Почему так много масла из картера по носку?

@jsa2001 2 ай бұрын

More percentage of castor oil in the mix and diesel engines are naturally messy. The exhaust was just collecting in the bottom of the engine mount.

@user-ip8wv3hq6j 2 ай бұрын

@@jsa2001 Впереди и сзади опоры коленвала нужно проточить два кольца шириной 0.4 мм, они будут являться сальниками. Между коленвалом и втулкой, если она там есть как подшипник скольжения, не будет подсоса воздуха через носок картера. Режим работы будет более стабильным на фигурах.

@jsa2001 2 ай бұрын

@user-ip8wv3hq6j There's a bit of play behind the prop shaft that's normal with these engines, they only have a plain bearing.

@user-ip8wv3hq6j 2 ай бұрын

@@jsa2001 В России много было таких моторов, из которых масло текло со всех щелей 🤣. После доработки они работали совсем по другом, даже те которые были с подшипниками качения в картере, тоже нуждались во втулке из бронзы.

@jsa2001 2 ай бұрын

@@user-ip8wv3hq6j There is less oil than what it seems coming from that gap , the whole engine is full of oil from the exhaust. Some paw engines have double bearings these are excellent diesel motors. Ive just been testing another engine today from red fin www.redfinengines.com another British manufacturer. A 049 engine its going back to them as the con rod is bent. might put that video up.

@hughloxdale4617 2 ай бұрын

A wonderful celebration of a great pioneer of powered flight. Well done Percy and the people who in 2003 proved that his heavier than air machine may have well flown successfully …with a few refinements. My only criticism: the film never mentions that other great early pioneer of powered flight, John Stringfellow (1799-1883), who flew a steam powered model aircraft down the length of a disused mill in Chard, Somerset in 1848 and which may have succeeded in travelling 60 yards or more. As you enter the town of Chard, a sign says something to the effect ‘Welcome to Chard, the home of powered flight.’ So dear Wright brothers, you can’t claim all the glory for the invention of powered flight! 😊

@hughloxdale4617 2 ай бұрын

According to the book ‘An Ancient Air’ by Harald Penrose, Smithsonian Institution Press, Washington DC, (1989), suggests that the flight of 1848 was only 40 yards, but different sources give different values.

@televirn5879 3 ай бұрын

Can it roll coal?

@pcka12 3 ай бұрын

Ah! The smell of diethyl ether in the morning!

@jsa2001 3 ай бұрын

Yeah the smell and also the slimey mess.

@luissouza5501 5 ай бұрын

Show !!!!!!!!!!!!!

@alwin1468 5 ай бұрын

Can u give stl file for print thanks

@jsa2001 5 ай бұрын

Designs - Thingiverse www.thingiverse.com/jsa2001/designs

@Mr.Westery 6 ай бұрын

Let's solve the mysteries in this documentary together. You're invited!

@cyclonic561c6 7 ай бұрын

Use a standard 540 silver can, paper shim plate, fit Tamiya 54628 08 Module Steel Pinion Gear (17T), flipped. Just as recommended by Tamiya. Works a treat.

@stevenzacharakis 10 ай бұрын

The easiest path to this is ordering Tamiya 54629 - 19t steel pinion 0.8mod to suit.

@chowchowww Жыл бұрын

New to the hobby, thanks for the video. Where can I buy those lights and how to setup them? I have a Carson reflex stick controller and can’t find any button that I could use for that. Thanks!

@jsa2001 Жыл бұрын

I got the lights from sky rc hobby store on ali express. Watch my video here on lights and switches. kzfaq.info/get/bejne/e6yfpq-CuKqciGQ.html

@fajeidea Жыл бұрын

Apakah alat ini memiliki mode standby sleep ketika gagang solder dan gagang solder uap di simpan di tempat nya.tx

@Dave51262 Жыл бұрын

Great idea with the 7mm shim for the motor. Would you mind sharing the .stl file? Thanks.

@melvinnightingale7284 Жыл бұрын

Hi, very helpful how could I purchase a shim, I’ve got the same problem. Best regards Mel.

@rainsnow9174 Жыл бұрын

Thankyou for the review, just bought this exacy one for a small project to fix chip on board. Very rear I use soldering, but I've always found myself ive needed a station combo like this for the job on electronic chips and heat gun don't cut it for electronic tiny chips without control of air speeds.

@MauzyrockRC Жыл бұрын

Hey mate! Terrific job. Wondering if you would link me an .stl file for the your shim? I am currently looking at doing the same thing to mine. Cheers!

@huwtindall7096 Жыл бұрын

Pretty sure you can get a pinion from Tamiya that specially deals with this problem? # 3515006 18T Pinion Gear (MD11) is the oart nuumber. Fits fine on the 540. It's the original pinion from the Hornet which I believe had the same chassis but a 540 motor. The whole hop ups and compatibility thing is a nightmare. Tamiya don't make it easy.

@need4drift Жыл бұрын

Nice mod brotha. Did you change the servo epa on the remote controller as well or does it not have adjustable steering epa?

@martinkuliza Жыл бұрын

6:56"that's your sign that powers going to it " ACTUALLY IT'S NOT it actually has a meaning 3 Dashes (Depending on which side they appear on) means.... THE UNIT IS GOING INTO STANDBY MODE 9:28 "the company recommends you leave it on the full amount, basically " ACTUALLY THEY DON'T What they say is.... To ensure longevity of life they recommend turning down the heat and increasing the windspeed , but keeping it as low as possible so as to not unnecessarily load the unit. They don't say crank it up, they say , Try and keep the Temp down as much as possible Increase the windspeed instead, but only as much as is necessary I've got mine on 5.5 Speed works fine

@Surferslocker Жыл бұрын

Nice video and thank you.

@Immeasurable_Varx Жыл бұрын

My kid's ready for this upgrade,got any spacers left?

@misterfixit7719 Жыл бұрын

Thanks for this video Would Be interested In A spacer

@jsa2001 Жыл бұрын

Hi. yeah i have a few left over. I have a broken foot at the moment so i'm incapacitated

@orcnic Жыл бұрын

Hey Buddy, thanks for the video, Subscribed. Just wanted to know the lenghts of these dampers. I am not sure if you mentioned them😊

@jsa2001 Жыл бұрын

Hi. The longer shocks are 100mm and 85mm for the smaller ones.

@stephencorsie8104 Жыл бұрын

Any ideas how to fix it ?

@stephencorsie8104 Жыл бұрын

I bought one 2 years ago and It does not recognise the r c

@peepdaasleeppolice8348 2 жыл бұрын

Did you try flipping the pinion gear

@davidisenhower2821 2 жыл бұрын

Why did you go through all that trouble to make a shim? All you had to do was turn the pinion around!!!

@jsa2001 2 жыл бұрын

I said in the video if you buy those pinions I used you need to make a shim for the tamiya silvercan 540. Like I said the motor shaft is not long enough.

@markharrisllb 2 жыл бұрын

Have you seen the price of the now? There’s two sellers on eBay selling then for £88! Mine was £38 last year. I’m pleased with mine but I’m not sure they’re worth £88.

@Alexander_l322 Жыл бұрын

Bollocks I just paid 70 quid for mine on Amazon! I couldn’t find one cheaper. I’m pissed lol

@rainsnow9174 Жыл бұрын

@@Alexander_l322 just bought one for £48 guess cost of living went up since you bought it

@agw5425 2 жыл бұрын

It would be nice to hear if you think it is worth the 60£ it costs(or did you get it for less?)

@jsa2001 2 жыл бұрын

Mine is still working, it was cheaper when i bought it, everything is more expensive now due to inflation.

@tara1050 2 жыл бұрын

Hi 😊 Do you have any more adapter plates for the 540 motor please??

@jchumley57 2 жыл бұрын

This is a documentary about a group of guys the the 2010s who built a plane that kind of looks like something Percy Pilcher might have designed in 1899 except for all the changes they had to make in order for it to actually barely fly. A factual documentary on Percy Pilcher would have been far more interesting.

@btdtgg 2 жыл бұрын

I sent you an email last night. I hope you see it.

@btdtgg 2 жыл бұрын

Thanks for the video. I ran into the same issue tonight.

@oldskoolhunting 2 жыл бұрын

I’ve an 18t pinion and a sports tuned silver can motor coming from Amazon soon…. I just bought it on a whim and it’s for my 2015 monster beetle with an etronix radio set up… I’m gonna run it on a 2s lipo as well… am I doing the right thing??

@jsa2001 2 жыл бұрын

Should be fine, use a steel pinion rather than an aluminium one. But I think your gears will wear quicker.

@tiborvon 2 жыл бұрын

Very nice dude 👍

@southwestsellerss147 2 жыл бұрын

Do you still have anymore of those shims going ?

@jsa2001 2 жыл бұрын

Yes I have some or can print some more.

@andremay5761 2 жыл бұрын

Bud, all you have to do is mount the pinion backwards on the shaft,long time trick

@jsa2001 2 жыл бұрын

@@andremay5761 No you can't because the motor shaft is not long enough.

@andremay5761 2 жыл бұрын

@@jsa2001 I found that out right after I posted that,sorry,I was wrong

@vilv777 2 жыл бұрын

Same model i got.. But just dead today.. After one year....

@summerishere2868 2 жыл бұрын

I also got one of these for my work is good enough. I bought some proper tips though, the ones that came with the unit were so cheap that some burned out on the first usage. With good tips it works well, the hot gun is pretty good as well.

@dlacicagaming4799 2 жыл бұрын

What tips did you buy? Does it fit from other soldering irons?

@summerishere2868 2 жыл бұрын

@@dlacicagaming4799 "LUXIANZI", "900M" model with "Plating Film".

@tiborvon 2 жыл бұрын

Thats, a good bit of info mate. You wouldnt think the wire would corrode in this way

@gundogduhatipoglu2151 2 жыл бұрын

Hellp me

@gundogduhatipoglu2151 2 жыл бұрын

Hello. Runcam2 4k it gives wifi error on my camera

@alaazorba1973 2 жыл бұрын

This proves that my words are true. No one from Stevecraft spoke to me knows what the problem is about their failed device. Experience will prove this to everyone.

@alaazorba1807 2 жыл бұрын

A Stepkraft machine was purchased, its work is failing, screws come out of its place, the one who buys it will find what I say leave it to the people to try it better

@alaazorba1807 2 жыл бұрын

You are just ads that a lot of people will use and see how wrong it is

@nanoblasting 3 жыл бұрын

This is a very good idea, it turns out a lot can be done with a cnc machine. Thanks.

@jony5702 3 жыл бұрын

Hi cracking video, I've just bought this model. What battery does it take please?

@jsa2001 3 жыл бұрын

Hi use 7.2 lipo or NiMh. 3000 milli amp

Ең жақсы KZfaq

Пікірлер