So do you have both chemical injectors attached? Or do you plug one suction and use the quick connection one? Idk I need to know if you are using 1 or both on the machine
@Brian_the_repair_guy21 сағат бұрын
@@duderock123456 if you have one that is built on like the one in the video, you have to plug it to use the other injector.
@itztheurge3 күн бұрын
2nd day with a brand new Graco 390 PC and its not holding pressure, spitting out the waste valve when on spray mode. Balls are clean, lol, not stuck, no debris, everythings screwed on properly. No idea
@Brian_the_repair_guy3 күн бұрын
@@itztheurge find me on Facebook for help
@memooffroad9093 күн бұрын
Thanks brother . I just got one and isn’t holding pressure but after watching a couple of your videos I think I can figure out the problem
@Brian_the_repair_guy3 күн бұрын
@@memooffroad909 find me on Facebook if you have questions.
@cihatercen51513 күн бұрын
We are having a trouble with our Graco ultra max 695. I have just texted you from Facebook messenger. Can you help us please ?
@Brian_the_repair_guy3 күн бұрын
@@cihatercen5151 I will message you on Facebook
@MrMasterFlash4 күн бұрын
I just got a new to me 3800 psi pressure washer. Can I adjust it down to 3000 PSI to use my flexilla hose with it? Will I still get same gallons per minute?
@Brian_the_repair_guy4 күн бұрын
@@MrMasterFlash is Flexilla the water hose you will use to provide water to the machine?
@michaelwalder2395 күн бұрын
Runs great, but oil in loader. Because milky
@Brian_the_repair_guy5 күн бұрын
@@michaelwalder239 your oil is milky?
@scottbanghart54398 күн бұрын
Can I follow this video to repack my 795
@scottbanghart54398 күн бұрын
Y
@Brian_the_repair_guy7 күн бұрын
@@scottbanghart5439 yes, the repack process I the same for the 695 and 795
@scottbanghart54398 күн бұрын
Is that for a Graco ultimate MX 795 this re packing. video 11:19
@Brian_the_repair_guy7 күн бұрын
@@scottbanghart5439 yes, the same steps
@rubenkjbr8 күн бұрын
The best información about unloadres 👍
@Brian_the_repair_guy7 күн бұрын
@@rubenkjbr glad you like it
@joseruval48348 күн бұрын
Hi bryan my graco 390 blow the fuses 2 times do you think l should replace the a new board thanks
@Brian_the_repair_guy7 күн бұрын
@@joseruval4834 what is happening when they blow? Does the motor run, then blow later or immediately?
@joseruval48346 күн бұрын
@@Brian_the_repair_guy yes run and then it blows
@Brian_the_repair_guy6 күн бұрын
@@joseruval4834 find me on Facebook
@robertappleby66838 күн бұрын
I heard makita brick when they detect voltage issues but I've never had a bad one, even the 7+ year old 1.3ah that I've run till cut off many times but never charged hot or cold. Very good batteries.
@Brian_the_repair_guy8 күн бұрын
@@robertappleby6683 I can't speak for others, but these batteries were 2 and 3 years old. Never been used. As you see from the video, the charger did not detect enough voltage to charge. As I said in the video, I do not recommend this. Lithium is good, but still a bit dangerous.
@robertappleby66838 күн бұрын
@@Brian_the_repair_guy yeah I've had a couple of cheap Chinese LiPo from my drones go off, a lot of power in those little suckers. Handy tip, thanks for the vid. 👍
@charlottesspot9 күн бұрын
No bs with Mr B
@nodeal73379 күн бұрын
Hi Brian.. Love your tips and detailed insight. I've got 3 Graco sprayers. 30y 390 - 495 and 695 and fix them myself. The 695 was bought used. Got it for a good price as it was totally drenched in paint, the top layer was a red color, oil based paint after it was used to paint a barn I think. There where hardly a spot of metal or blue to be seen on the machine housing or hose. Took a big brush and covered everything with gel paintstripper, the hose, wheels, everything. Was careful not to leave it on the machinehouse for too long and eat into the Graco factory paint. Toothbrush and scrapers etc.. Took it to the guy who sold it to me a few days later. He stood there gasping, it looked brand new. New seals and packings. Seeing some of the machines you work on, I wonder what the hell these people are doing. They have 15m of hose but It looks like the sprayer is 2m away from the substrate they Spray Mist from 1m away? I don't know ;-) I mean If you know it will be messy. I'll put some WD40 on and wipe it off afterwards, I cover the machine housing and move it further away. And I clean up when I'm finished 🙂
@Brian_the_repair_guy9 күн бұрын
@@nodeal7337 thanks for watching. After 32 years of preparing this equipment, I have stopped asking how guys get their equipment get to such a state. There are a number of things you can do to prevent this as you pointed out. It never seems to set in the minds of many of the painters. I explain how it benefits them to keep their equipment clean and they make their choices from there The purchase of a sprayer seems pricey at time of purchase but the money you can make quickly clouds that cost in their minds. Thanks again for watching
@AlbertoCastillo-tg7ci9 күн бұрын
Im having the same problem on a 1095. I’ve tried replacing just the cap but still leaks when the pump starts to build pressure. Any other things i could try other than replacing the whole filter housing ?
@Brian_the_repair_guy9 күн бұрын
@@AlbertoCastillo-tg7ci if you have replaced the cap and Oring and the leak continues, try tightening a bit more. If it continues you have to replace the while housing
@user-lh8nn4fx8x10 күн бұрын
Any good technique for remove stuck valves? I got 3 out but 2 severely stuck.
@Brian_the_repair_guy9 күн бұрын
@@user-lh8nn4fx8x you just have to work it out. Typically if they are stuck, they have expanded and will need to be replaced any way
@jabbaweezy12 күн бұрын
I put in a pump from a working machine and still lack of pressure.
@Brian_the_repair_guy12 күн бұрын
@@jabbaweezy find me on Facebook I will be able to help you better
@danielkancar634612 күн бұрын
Brian! THANK YOU! You had the best video out there. Your explanation was amazing. Much appreciated. Thanks for being a great guy.
@Brian_the_repair_guy3 күн бұрын
@@danielkancar6346 I am glad it was helpful
@VenusTukpah13 күн бұрын
Hey Brain hope u doing good? my pump lost pressure how can u be a help
@Brian_the_repair_guy13 күн бұрын
@@VenusTukpah find me on Facebook.
@Funckinnutcase14 күн бұрын
So if my motor binds up and just hums, when it gets hot, then works again, after cooling down, would that's be a bad motor and not worth replacing the brushes?
@Brian_the_repair_guy14 күн бұрын
@@Funckinnutcase when the motor gets hot enough to shut down, the possibility is high that other issues are going to be there. The brushes are fairly cheap, so it couldn't hurt to replace.
@djack56817 күн бұрын
Thank you
@Brian_the_repair_guy17 күн бұрын
@@djack568 I hope it helped
@Robert-vv9yg19 күн бұрын
I have this same pump. I am having problems getting the siphon to pull solution into the pump..I have completey tore down and re assembled the pump. Removed the injector, cleaned it and still nothing. I have new valves coming and a few other parts. im curious what pressure washer would you recommend for a home owner? instead of this type pump? Thank you for the video.
@Brian_the_repair_guy19 күн бұрын
@@Robert-vv9yg I have a video specific to the chemical injector. Take a look at that one. Most of the time an injector is not affected by the pump itself. A pressure washer with an AR pump with a horizontal engine would be a good one
@Robert-vv9yg19 күн бұрын
@@Brian_the_repair_guy Ok. Thank you Brian
@Robert-vv9yg18 күн бұрын
@@Brian_the_repair_guy So the injector will siphon without the wand. But as soon as I connect the wand it stops pulling..the wand has no restrictions ..any thoughts
@Brian_the_repair_guy18 күн бұрын
@@Robert-vv9yg if your getting chemical with the pressure hose but it stops with the wand and no tip added, then the wand is the issue. The wand will corode on the inside and reduce the interior of the wand. This reduces the water volume, so no chemical. If this is the original wand, replace it. Make sure it is a good one pice wand. Not a wand that can be hand unscrewed from the handle. One piece wand and gun
@Robert-vv9yg18 күн бұрын
@@Brian_the_repair_guy ok thank you.
@KalebDHopkins19 күн бұрын
What I don’t get it how you at the beginning of the video, you couldn’t pull it then when you pulled spark plug you magically could pull it. When it won’t pull how do you get the fluid out and back at the start, how do you get it to pull…. Super confusing that you couldn’t then could. You skipped the entire part your videos title describes. :/
@Brian_the_repair_guy19 күн бұрын
@@KalebDHopkins sorry if I didn't explain it well in the video. Liquids cannot be compressed. With the oil in the cylinder, the piston is trying to compress the oil in the cylinder. This is why it is locked, there is no where for the oil to go. When you removed the spark plug and pull the oil is pushed into the upper head and into the spark plug hole. This allows for full rotation of the crankshaft and full stroke of the piston. If you pull hard like you are trying to start it, the oil will shoot out of the cylinder. Repeatedly pulling hard will force the oil out. Or you can spray inside the cylinder with an air compressor
@KalebDHopkins19 күн бұрын
@@Brian_the_repair_guy awesome thank you for that. Makes much more sense, thank you
@Brian_the_repair_guy19 күн бұрын
@@KalebDHopkins no problem. Anything else just ask
@KalebDHopkins15 күн бұрын
@@Brian_the_repair_guyso what should I do/try next if it won’t pull still even with spark out? There is oil in the engine still, and doesn’t look like the worst I’ve seen.
@Brian_the_repair_guy15 күн бұрын
@@KalebDHopkins if if is not pulling without the plug, then the engine has a mechanical failure. Try removing the recoil and put a ratchet on the fly wheel and see if you can move the fly wheel in the opposite direction
@JustinPeterson-uf1lk20 күн бұрын
I got a hp5535 pump, what oil do I use?
@Brian_the_repair_guy3 күн бұрын
Sorry. I missed your question. SAE 30 nondetergent
@@NathanBallenger I really appreciate your comments and positive thoughts. I try really hard to keep it quick and simple. I know how you feel about most videos on YT. I feel the same so I try to do it the way I would want them done, to the point. Please share my videos with friends and if you have any questions, find me on Facebook
@khadijahdavis157225 күн бұрын
This video was extremely helpful thank you so much
@Brian_the_repair_guy25 күн бұрын
@@khadijahdavis1572 I am glad to help
@kaguila25 күн бұрын
Wow! That was very helpful at the right time. Thank you for taking the time to make this video.
@Brian_the_repair_guy25 күн бұрын
@@kaguila I am glad it helps
@AlbertoSanchez-ro3ug26 күн бұрын
I followed your instructions and now I’m back up and “pressure” washing. Thanks for your informative video. 😎
@Brian_the_repair_guy26 күн бұрын
@@AlbertoSanchez-ro3ug very glad to help. Now go make money
@aigauthier198026 күн бұрын
What years were the ultimate Mx in production? Also can you still get parts for them? Thanks.
@Brian_the_repair_guy26 күн бұрын
@@aigauthier1980 I am not 100 percent sure of production years. I believe mid 90s to the early 00s. Most of the parts are still available.
@jeffbaloga437627 күн бұрын
Great video and great explanation!!!! Thank you!!!!👍👍👍👊👊
@Brian_the_repair_guy26 күн бұрын
@@jeffbaloga4376 I hope it was helpful
@fraydcat27 күн бұрын
Can you check the packings without replacing if they still look good? I had left insides of my sprayer not protected over a couple of winters and that resulted in the large ball rusting and pitting along with the foot valve housing that was badly rusted... The packings looked perfect, this is a unit that rarely gets used and prob has a total of 25 hours on it, if that... Does Bedford sell all these parts for the 440i? Also, what type of grease are you using for assembly?
@Brian_the_repair_guy27 күн бұрын
@@fraydcat any kind of grease is good. The packing will come with grease if you get them. To check the packing, prime it. Once the system stops pumping under pressure, it should hold for 30 seconds before another stroke. It may stroke right after the prime valve is turned off a couple cycles but wait. If the pumping stops, packing are good. If it keeps stroking packing are bad
@fredygutierrez927727 күн бұрын
If you still have that part you removed, you can send it to me. I need two parts of that.
@Brian_the_repair_guy27 күн бұрын
@@fredygutierrez9277 I do not, sorry
@HappyHands.28 күн бұрын
Does lowering the pressure regulator make the pump last any longer?
@Brian_the_repair_guy28 күн бұрын
@@HappyHands. if it does, it would be negligible. The pumps are made to reun at max pressure for many hours
@Hec-Thor-2328 күн бұрын
Greetings, I would like to ask you a question. My pump is a general pump as well and it leaks the oil from the bottom. Should I replace the gasket? It builds pressure but it leaks a lot of oil. I took off all six valves and everything seems to be OK. Can you tell me where I can buy the parts please?
@Brian_the_repair_guy28 күн бұрын
@@Hec-Thor-23 the oil seals need to be replaced. They are at the end of the plunger towards the crank case. Check with watercannon.com for the parts
@Hec-Thor-2327 күн бұрын
@@Brian_the_repair_guy thank you… your videos are great keep it up
@Brian_the_repair_guy27 күн бұрын
@@Hec-Thor-23 thank you, hope it helps
@51jahloveАй бұрын
Excellent presentation. I learned a lot from your video. My Honda GX390 3600 psi was building pressure @ 3200 psi. As soon as I press the trigger the pressure immediately dropped to 2000 psi. Now I know what to do to fix it. Thanks to your very informative video 👍🏽
@Brian_the_repair_guyАй бұрын
I hope this video helps. I have a couple others on loss of pressure as well. Be sure to watch those
@kuantancatatap4161Ай бұрын
Thanks
@Brian_the_repair_guyАй бұрын
I hope it helps you
@darylrollemanАй бұрын
lol i got covered in oil because i pulled without the spark plug just to see if it had loosened. I continued the video and you said watch out cause it’s gonna spray out… i laughed at myself… Great video! Helped me out a lot cheers
@Brian_the_repair_guyАй бұрын
You jumped the gun.
@samuelregalado506Ай бұрын
🤙🏼
@MoniqueRamos-t7cАй бұрын
Thank you so much for being so clear in this video. It was very thoughtful. I sent a little $ to thank you. Cheers.
@Brian_the_repair_guyАй бұрын
I greatly appreciate this. You are very generous
@MoniqueRamos-t7cАй бұрын
Thanks!
@Brian_the_repair_guyАй бұрын
Thank you very much, I am glad it helped
@richlarson3463Ай бұрын
Thank you for making the video. I just got my MX unit and sprayed maybe 3 quarts of latex through it with an 08 or 10 tip. I will read the manual :)
@Brian_the_repair_guyАй бұрын
I would definitely think about switching to a larger orifice tip
@CarnabwthАй бұрын
Our pressure washer pump looks similar to that one. I switched it on today. Hadn't been used for maybe a year. It's actually my borther in law's machine. The pressure washer started up straight away but absolutely no water was being sucked up. I put my hand at the end which is supposed to suck up the water and there was nothing. What do you think could be wrong? These videos of yours are very interesing. Thank you.
@Brian_the_repair_guyАй бұрын
When you say sucked up, do you mean the chemical injectoe?
@CarnabwthАй бұрын
@@Brian_the_repair_guy Thanks for replying. No, I mean the water. The inlet pipe is put into a tub to such up water. This has mesh at the end to prevent any debris uptake. It just isn’t sucking up any water. It's never had and inlet pipe which screws onto a tap. It's placed in a tub of clean water.
@Brian_the_repair_guyАй бұрын
@@Carnabwth do me a favor. Find me on Facebook you can send me pictures of the machine and parts that you are talking about
@siprecords1Ай бұрын
Thank you I needed this video great details on how to clean and use it
@Brian_the_repair_guyАй бұрын
Glad to help
@donl3381Ай бұрын
Great video. I need help. Pull start cord rips out of my hand when i attempt to pull / start it. Does anyone know why and the fix? Its been a year and I'm still at a dead end. Ryobi GCV 190 3100psi 2.5 GPM
@Brian_the_repair_guyАй бұрын
They can do that on the compression stroke. I usually cycle through a few pulls to the compression stroke, then make my pull
@MrKaazАй бұрын
@Brian.... I have a Westinghouse 2700 pressure washer with a Westinghouse 212cc engine. I need a new water pressure pump assembly but am having trouble finding actual replacement parts for a "Westinghouse" unit. I'm reluctant to purchase one of those cheap knock off pumps from that Large online retailer bc they just seem too underpriced. Are you aware of a decent aftermarket or compatible pump and where to buy? Such as Maintenance parts: water pumps, carb rebuild kits, etc. Thx
@Brian_the_repair_guyАй бұрын
Watercannon.com does a great job with keeping a huge selection of parts and pumps for pressure washers. I personally lean towards the AR pumps on the smaller units
@uptodatimet6Ай бұрын
I have question. My pressure washer build up pressure when the equipment is off what can cause that problem?
@Brian_the_repair_guyАй бұрын
I am not sure what you are asking. Can you reword the question
@vintage-jm2fvАй бұрын
Brushes were good. Bought it used after it had been outside in the weather for 2 years. Pumped solvent fine but smoke coming out vents after 5 seconds. Took apart again so armature in my hand. VERY warm after 5 seconds of run time and 5 minutes to disassemble. All I can guess is a short inside the spinning armature. Oh well.
@Brian_the_repair_guyАй бұрын
Exactly right.
@vintage-jm2fvАй бұрын
Awsome video thx Canada
@Brian_the_repair_guyАй бұрын
I hope it helped you
@missypeppers3193Ай бұрын
How do I find out what check valves I need on my machine
@Brian_the_repair_guyАй бұрын
Your pump model number should be on the top of the pump and you can Google it from there. Or you could contact watercannon.com they are pretty good and figuring the pump out
@davetemplin8957Ай бұрын
Hi Brian - thanks for your video. Tried all of your steps. Rope pulled easily when I took the spark plug out and I didn't see anything come out of the hole. Put the spark plug back in and then it was hard to pull again. Any thoughts? Troy Built Pressure Washer, Briggs and Stratton Engine 875exi series, 190cc OHV. Thanks
@Brian_the_repair_guyАй бұрын
If it pulls with no plug, but locks with the plug then most likely there is still fluid in the cylinder. If you have a compressor, blow the cylinder out.