This is more of a highlight of what you know vs. a tutorrial hahaha. You make it all look so easy bro. Talk us through step-by-step next time. We know you know your stuff. There's a lot more to aiming your headlights. Talk us through that process. Goos stuff though, this is just too high level for me, I need more instructions.
@shadowalker182 күн бұрын
If you want to be even faster about it you can actually remove the radio and it's right there
@gentlemenofreal67292 күн бұрын
Hey, I have a question. I’m not sure if you’re gonna know so my Freon is constantly leaking out. I put the UV dye. I don’t see it on any of the lines. Could it be the compressor gasket? Should I just change the whole compressor?
@Groux5043 күн бұрын
This video is for advanced mechanics who just needed visuals 😂👍🏿 thank you tho bro
@josephherron76715 күн бұрын
How there hell did you get that out through the wheel well? I tried to half an hour and it’s not coming. I was about to pull the alternator and come out from the top until I saw this. Now I’m more determined than ever to get it from the side.
@Kangol_Automotive5 күн бұрын
You have to remove the front of the fender liner and the pipe on the subframe pop it out of the white brackets then you and work it out
@josephherron76715 күн бұрын
@@Kangol_Automotive I did that. I Removed the fender liner and the pipe. It’s getting caught between the engine block and the chassis but it’s just barely catching. Like, if I sanded down the chassis it would almost come out. One thing I didn’t do is remove the wheel. I was trying to work around it because I was in a bit of a hurry (storm clouds on the horizon). I’m going to pull the wheel tomorrow and try again before I pull the alternator.
@josephherron767113 сағат бұрын
@@Kangol_Automotive i got it. Had to push it back and rotate it 90 degrees clockwise. Then it came right out.
@ernestelizardo19716 күн бұрын
😂.
@Playtimersalad10 күн бұрын
Did you have to remove the outside door handle assembly?
@billylocklin414913 күн бұрын
He'll I took mine to CHIEF Radiator best in Dallas TX.
@nishangill252217 күн бұрын
Best video, to the point, no BS.
@Jared_Albert18 күн бұрын
Thank you excellent video!
@perryaguilar57023 күн бұрын
How did you discount the part that hooks into the exterior door handle?
@angelaldacoaa23 күн бұрын
Skiped all the most important parts bro
@southpark15975323 күн бұрын
What a stupid place for a blower motor, seems like Toyota and Nissan loves to cram as much junk in one area as possible. Thanks man
@victorlee732328 күн бұрын
Hi may i know is this require to reprogram after replace the key switch?
@daproductАй бұрын
Driver side or passenger?
@alexanderbrown2982Ай бұрын
Thank you very much for this, I really appreciate it. All I can say though is that my Rotors had become one with the wheel hub lol. Double hammer, WD-40 and finally torch got them off. Thank you again!
@moe3575louАй бұрын
Hey Bro, what was the torque specs from the pump to the block? Getting ready to replace mine. Just don't want to over torque or under torque them bolts!
@chelle315Ай бұрын
Demonstration vs tutorial. Don't forget to remove & re-install the O2 sensor....also replace gaskets as needed.
@VictoriaBressmanАй бұрын
THANK YOU!
@BillSWАй бұрын
Best video I've seen how to replace the shifter. No babbling or wobbly cameras. Nice! Next time give the socket sizes needed
@travisbaker7461Ай бұрын
Nice intro 🎶 🎵
@jasonbay13Ай бұрын
bad video for anything beside location
@sjcafieroАй бұрын
What the heck? You showed absolutely NOTHING
@jvz2319Ай бұрын
Should’ve shown how to remove the actuator
@setheubank314Ай бұрын
This video fuckin sucks. You can't anything except that fuckin music
@DiamondmahoneyАй бұрын
Mine just went out on my rouge I just dropped it off this morning to get some
@kaylabrooke2907Ай бұрын
Nice video.. straight to the point. Ive seen these videos where ppl load up with grease and some without greasing anything before re-installing. Any good practices youve found. I know the sealed hub bearings come pre-greased
@marce6969Ай бұрын
i like the music choice
@DakhilBАй бұрын
Mechanics Love Changing The Whole Assembly Instead Of The $10 Switch ..
@d7im619Ай бұрын
for anyone want to do it himself, you will need speical tools to remove hose clamps on the lower driver side, its pain in the ass tbh cuz its very tight there or if your are replacung the hoses too u can cut them off
@MrKago1Ай бұрын
Small town I went to high school in had a problem with flooding on Msin street. So the curbs were a foot and a half high. Some old lady managed to not only get her front tires of her Cadillac Eldorado up that curb, she got all four tires on the sidewalk and the fron bumper through the cinder block wall if the post office.
@trael.136Ай бұрын
It was Grandma driving. She just got her medical card.😁
@90sbuickguy84Ай бұрын
That’s not a Buick that’s a Cadillac Fleetwood it’s on the same platform as a Buick roadmaster though and it’s General Motors sedan so you’re halfway there
@Lonnie1969sАй бұрын
I was reading the sign 😅 didn't see the car up a pole!
@TrueFollower556Ай бұрын
Same😂😂😂
@Funfella4lifeАй бұрын
Someone's grandma is going to be pissed
@andywilkinson8041Ай бұрын
Not even on hydraulics 😂
@creepycraiyons3519Ай бұрын
Squatting getting outta hand
@iheartwheeliesАй бұрын
Who else was like “ yeah, juicy, butteriest, craving a burger”
@IdkwhodawgАй бұрын
🤣🤣🤣 thank god I’m not the only one. I thought it was just somebody’s dad making a dad joke.. 😭
@Hondaone1Ай бұрын
What restaurant has that slogan?
@emmcee476Ай бұрын
Remove kick panel, unplug connectors on pedal assembly, detach all connector push clips, remove metal box and bracket under column (gave me more room), disconnect steering shaft at the TOP section (can be slid down easily by hand), remove pedal assembly, remove blower motor Removing that metal square box and its bracket, and disconnecting that top section of the shaft, will make the job a lot easier
@kiondremarshall700Ай бұрын
Did you have to split the wires bc my Ford has 5 wires and the resistor I bought have 4 what am k supposed to do
@simon.jacobs.0709Ай бұрын
The gloves and the Star Wars music really make the video .....
@fernandomeza14162 ай бұрын
What type of scanner you using here?
@Wholesomewarriortv992 ай бұрын
Ordered mine only for $125 off amazon
@borregos92102 ай бұрын
LOL! I guess I should know how to remove everything by just watching.
@barrybelanger91172 ай бұрын
How do you relearn a throttle body without scan tool
@shibaartista42742 ай бұрын
How many hours of labor is this ? I was quoted at $350
@ginger_king_12342 ай бұрын
😂😂😂 my bro moved from San Francisco to Texas bought a house and the closing went so fast buddy thru in his Silverado escalade for free. guy rip apart a Silverado and rebuilt it with Cadillac stuff .
@Honey_Soles2 ай бұрын
I have a crank no start, had a P0113 but it was the wiring on the IAT sensor connector, I replaced the wiring to the sensor connector, codes cleared but still crank no start. Any advice? It’s a 2010 4.0 T & C
@tonkaGuy8882 ай бұрын
So basically, take the old one off and put the new one on. Solid.