I did everything to a T and still doesn’t click over and begin wash mode. I can hear it try but no dice. Super annoying. I even replaced the dogs because those were stripped too
@seanhook8912 күн бұрын
So I followed everything. My diagnostics said sensor error too. I got a new actuator and triple checked i put it back in right. I even recalibrated too. Still when it goes to wash mode it just does nothing but you can hear it try to click over but doesn’t start washing. Hellllpp😢 haha
@seanhook8914 күн бұрын
Great video and thank you and it worked but I NEED THE second video
@_Parkbench5 күн бұрын
Did you keep the 2 piece axle ? If so how has it done with the locker ?
@OFFAxisBuilds5 күн бұрын
No I replaced the two piece axle.
@miguelmojica56296 күн бұрын
Where did u order the bar from
@OFFAxisBuilds5 күн бұрын
I ordered it from Amazon. amzn.to/3Aj0ZpV
@markthomas40836 күн бұрын
I am having trouble w the Pitman arm. Do you remember what size socket is required? 1/1/8”?
@OFFAxisBuilds5 күн бұрын
Honestly I had trouble with it too. You can heat the pitman are up and us the correct puller that goes all the way around. I actually gave up and just ran the stock arm. Never had any issues
@markthomas40835 күн бұрын
@@OFFAxisBuilds thank you air. I will probably do the same.
@Bosco-gets-it-right7 күн бұрын
And on eBay the starter is $43 w free shipping
@AdreamToast8 күн бұрын
Thank you so much!
@stillrumone8 күн бұрын
😎💪💪💪💪💪
@BillKirkpatrick11 күн бұрын
Is there a spacer plate under the shifter?
@OFFAxisBuilds9 күн бұрын
Yes but some years don’t require it
@Me-ew8uh13 күн бұрын
I have the same exact code. The control board is what the code is for. I keep reading different answers. But the shift actuator was never even on the list for that code.
@DustySteel13 күн бұрын
Awesome! How did it run?
@dominicanwtf623514 күн бұрын
I did all that, and replaced the part and NOTHING, still not passing SENSING
@markthomas408314 күн бұрын
My third comment, the post install pic is cool, most videos forget to show the finished product.
@markthomas408314 күн бұрын
After 7 years have passed, how do you like the lift kit sir?
@OFFAxisBuilds13 күн бұрын
I just recently upgraded to the rubicon express military wrap. Those RC did well.
@markthomas408313 күн бұрын
@@OFFAxisBuilds good to hear. 😎
@markthomas408314 күн бұрын
Great video. I appreciate the detailed info.
@pgiessel23 күн бұрын
This video was fantastic. I couldn't figure out how to change the ignition switch. This showed me exactly how. It was still very difficult to get out. Mine was very stuck, but its removal wouldn't have been possible without this video. Thank you!
@Patriot179027 күн бұрын
My washer is spinning, but not enough to wear clothes are still wet. Could it be the belt or clutch?
@pamelascholz9680Ай бұрын
This is a semi annual event for me fly wheel wont tighten up, should i reloave assembly or just try spring.
@NotHere2SellCookiesАй бұрын
We rent and this is the washer that was here. We have a maintenance guy that owns an appliance repair shop and the employee he sent can't figure it out either. I absolutely hate these things. Been washing my stuff at my mother in law's house for a week now...
@premiumexcellence3709Ай бұрын
It doesn’t pop up you don’t know what you’re talking about
@OFFAxisBuildsАй бұрын
It popped up I’m mine.
@markf4720Ай бұрын
This needs much more explanation otherwise people following it will overtighten and wear their steering boxes out very fast. Its best to eliminate play from all other areas before messing with the box (i.e. tie rods, u-joints etc). If you adjust and your steering doesn't return to 45 degrees before centre then it's too tight and you need to slacken the adjustment otherwise your box will wear out fast.
@joeybelton5578Ай бұрын
Loose all the u joints get a double D shaft
@c.l.5732Ай бұрын
I pulled the inter Drum, and used Dawn on the seal. That's just me......
@shlomogoldenstein344Ай бұрын
“Lets see if we can start this guy” Cuts out the part where he starts it
@startnowadventuresАй бұрын
Where is the rest of the video!?! You got 1/3 of the way and then just ended with “ok I’m done”. What happened? I mean, seriously, the cutting it off part is obvious, I wanted to see how you put it back together, any issues you ran into etc.
@OFFAxisBuildsАй бұрын
Yep you’re right I was going to post the second part of the video and haven’t gotten to it yet. Do to answer your question the only issue I had was realigning the doors. After I cut the corner out the body dropped. I corrected some of it when I bolted and welded the boat side back on. The other part had to be corrected either way the hinges. I will see if I can get the follow up video edited and posted soon. I got busy and forgot to get back to it.
@kylecross8770Ай бұрын
is it possible to remove the rubber seal from the transmission? or do I need to buy a whole new transmission?
@JGG1701Ай бұрын
Is it me or are Jeeps famous for ignition switches going bad? Thanks for sharing this with us 😊
@caseycole9485Ай бұрын
Chinook
@anthonyburke1933Ай бұрын
Thanks next time don't do any pain killers your high
@l.p.4294Ай бұрын
Amazon review lead me here...good luck with your build
@OFFAxisBuildsАй бұрын
Thank you. The install took more than I expected but I also wanted them further forward because I didn’t want my knees into the steering wheel. They seem to work great. I need to get back onto the build.
@hanks5216Ай бұрын
My washer is stuck in flood mode I believe. Nothing I've tried seems to fix it.
@pinkfreud622 ай бұрын
What a load of b.s. these washers are. Just need a basic fill, wash, rinse & spin. Washers lasted 20 yrs just doing that. No one should have to be a diagnostic tech or mechanic to have an appliance last a good 10 yrs at least.
@yetirider43462 ай бұрын
You should sell some of them
@OFFAxisBuildsАй бұрын
Are you interested in one?
@user-py4kg3qx7x2 ай бұрын
Sensing shifter not working due to lid lock ? Is that possible? Replaced lid lock sensor but lid lock did not activate went through diagnostic steps to it washed see if it shifts past wash it was stuck in sensing ?! Now it advanced to wash?!
@user-py4kg3qx7x2 ай бұрын
Built a off road vw bajo with close lights n porche. Parts with my brother in 1983 with a crome stinger tail pipe badass background
@OFFAxisBuildsАй бұрын
Thank you. It’s a fun project. I need to get back on it. It’s actually a lowered Baja bug. It’s more of a volksrod.
@MattBushRS2 ай бұрын
Damn the whole reason I was here is I lost my key lol was so disappointed when I got to the part where you need the key :(
@roullpena88782 ай бұрын
What are the yellow and white switches called ? I disconnected mine and a small copper piece fell out as well and now I can’t get my jeep to start after finishing installation
@king_king892 ай бұрын
how i can know gearbox need to change? whirlpool WTL1300SL
@wesschaan89462 ай бұрын
Why would you skip the procedure of taking the window off the regulator
@planetoffroadtahar29212 ай бұрын
600 $??????? It cost me 75 $ spark plugs and 165 $ coils....NGK ..ALL
@OFFAxisBuilds2 ай бұрын
When I had the work done the coils were more expensive
@arthowes84232 ай бұрын
I changed shifting sensor and it changed nothing….what next? Is my washer junk?
@refragged3 ай бұрын
You saved me $600. THANK YOU.
@davec60163 ай бұрын
NO do you understand how lucky you are to find a SERVICE manual just taped inside the washer ? I can't imagine they did that often and when they did that it stayed inside the washer when you come across one years later. if I had a manual, I wouldn't need you to explain a thing !
@algijura3 ай бұрын
why does mini says fuel filter is lifetime 😅😅😅😅
@OFFAxisBuildsАй бұрын
Maybe mini’s life time is 100,000 miles. That’s when you want to sell it because you will start to have a lot of issues.
@hapamamaofthree3 ай бұрын
My washer is having this exact problem. After pressing start while done is selected and all are blinking, I clicked it counterclockwise as you did in the video. It was blinking sensing. I tried diagnostic mode again but turned it clockwise and different things lit up. I am confused on what my issue is now 🥴
@johnlucier85723 ай бұрын
Needs to stay away from washing machines. I have to laugh as to why this machine is still working, I mean really. It's insane to watch this.
@ckelly51413 ай бұрын
Is this washing machine diagnostics or safe cracking procedures? 🤔
@84Parker843 ай бұрын
Hello i have the same pedal assy in my bug. What size are your master cylinders?
@OFFAxisBuildsАй бұрын
They are 3/4 bore.
@OFFAxisBuildsАй бұрын
amzn.to/3LiZydm
@rogerlillo3533 ай бұрын
Can’t get this to pop out at all. Do I have to use a super skinny flat head screwdriver head?
@OFFAxisBuilds3 ай бұрын
You will need something small enough to fit through the hole to the plastic lever.