Gancycle

Пікірлер

@josepharagon8259 Жыл бұрын

That rear upper cassette bolt wasn’t visible in your video…. That could be a problem… was it there?

@trevorross8455 Жыл бұрын

I hate this motor wish I knew better to buy a 99 exploder for $1500

@trevorross8455 Жыл бұрын

To not buy*** lol

@brandimcfetridge2749 3 жыл бұрын

Do you know how to replace the one in the front on the other head? Without pulling the motor ?

@valrankov6827 4 жыл бұрын

Just my two cents. You can install this cabin air filter above the blower www.rockauto.com/en/moreinfo.php?pk=489028&jsn=7 Fits perfectly.

@iamdjnam 4 жыл бұрын

I want to attempt this. I’ve pulled the 4.0 so many times. Did you remove the front driveshaft? Did you remove the torque converter nuts?

@Gancycle 4 жыл бұрын

Yes disconnected front driveshaft and the touque converter nuts.

@iamdjnam 4 жыл бұрын

Gancycle thank you so much for the fast reply

@bigeaux504 4 жыл бұрын

I have a 2005 Ford explore and I have the same problem, great video thank you very much.

@bentonrodeheaver2596 5 жыл бұрын

I wanted to add that most vids online show removing the engine, alot of work and not everyone has a garage. Just know that my next vehicle will have (one not three chains) an easily accessible timing belt.

@bentonrodeheaver2596 5 жыл бұрын

I did the front guide block+ tensioner but I'm hearing a slap on the same bank as yours. However this gives me hope since I thought about tackling this in the same way. (or paying someone else to do it).

@felipevalles8041 4 жыл бұрын

There is a way to change just the tensioner...easy job ,look in you tube at least 2 guys already did it..

@iamdjnam 4 жыл бұрын

FELIPE VALLES not if the cassette snapped and dropped down.

@felipevalles8041 4 жыл бұрын

@@iamdjnam agree, if the cassette is dropped,got to pull the engine or at least separate the tranny just like this guy did,pain in the butt.

@iamdjnam 4 жыл бұрын

FELIPE VALLES I’m very confident in the way this guy approached this project. The least ford should’ve done was make an access hole on the bellhousing to reach the cassette bolt. They didn’t, so you have to remove 20 extra bolts.

@jpegjake 4 жыл бұрын

@@iamdjnam How hard was it to get to get the upper sprocket apart and torqued properly back together?

@bentonrodeheaver2596 5 жыл бұрын

I was thinking about doing the chains in mine, the front is slapping bad. But since it can be done and the right chain in the vehicle I might skip the left chain and put the guide in + let it fly . Thanks.

@joelgastelum3478 5 жыл бұрын

I had all the guides, cassettes and chains replaced with Ford parts except I used the same hydraulic tensioners I had. The thing is the rear of the engine still makes a slight rattling noise. The engine has 134k miles. Can it be these tensioners that are worn that aren't putting enough tension on the chain? Thanks.

@Gancycle 5 жыл бұрын

Joel Gastelum The hydraulic tensioners are known to make noise themselves. Replacing the hydraulic tensioner would be the first thing I would replace if I had any kind noise back there besides a grinding. That could be your problem. They do make noise when they fail.

@Texasknowhow 5 жыл бұрын

Was a little hard to watch, but this helped prepare me for my fix. Same vehicle (03 Explorer) and mine is blowing and all, but on fan setting 4 (highest) it sounds like there is something sucking to the fan or similar and the air movement is not in line with the #4 highest setting. i think my door may be laying in there as well. I agree with Andrew below - removing the glove box is simple and would have really helped you on this repair and with the camera angles. I was even going to say the seats remove from these things with 4 bolts and < 1 min of effort, that would have given you even more room to work. Thanks for taking the time and if you keep making videos you will get better at the post processing needed to make a good video. Keep it up! Thanks again, Clay

@scarfish7inches201 5 жыл бұрын

" WHATTA MESS!" . Hahaha! My exact thoughts when I did my two valve cover gaskets and intake manifold gasket. Same engine and im not a mechanic