Thanks! I'm going to attempt this in a few hours and your video is my guide!

What else can a person do to take that top with blue off,,couldn't remove it as the video shiwed

I just turned the whole thing upside down after i took off the nut and it fell off itself..

I just wanna know how to remove that stupid tub nut.. damn thing wont move.. would it unscrew clockwise or ccl? What you use to grab aholt and screw the thing?

I have this same washer 500 series (looks exactly like yours) except the inside has a tower with the softener hole at top. It is not spinning my clothes dry…they’re soaking wet! But there’s no water left like it’s not draining…just clothes are wet

Am I the only one that can’t figure out how to balance this washing machine? I distribute the clothes out very evenly around the perimeter of the washer and every single time in the spin cycle It shakes very violently! Does anyone have any tips on the best way to distribute the clothes around in there evenly so it doesn’t get out of balance? It is level as far as where it is sitting!

My screw is SO snug- I’m struggling to get it loose.

I can’t even begin to tell you how helpful this is. I loathe this washer and dryer combo… but maybe doing this will make me hate it less.

This round piece is held in by something more it hits loudly and is impossible to lift up. Even after popping the tub

Dupree?

Thank you for your detailed video. Tell me, where can I find its filter in order to clean it? I can't find it on the back of the machine.

What should I check if it won’t go past the rinse cycle?

Thank you so much for the video! I’m having trouble with a loud noise when it’s washing it’s like a clicking noise. I would love to try this technique and again thank you but I’m sure my husband‘s either going to call over repair person or will get a new washer and dryer lol!I am going to look up and see if you have a video on what I just mentioned though. Merry Christmas!

Ive been wiggling for past hour mines still stuck

I lifted my washer up off the ground by the agitator and it still won't come off. We washed a few loads after removing the bolt, dumped scalding hot water in it, sprayed wd-40 around it. Even with vice grips and pliers on the blue spines lifting and someone tapping the hub with a no bounce it just won't come up. I don't get a click or thunk when I pull up on the tub, when I pull up on the agitator the tub comes with it and maxed out at top of travel. I'm a lil perturbed.

Yes, just like to pass alone somethings that i learned. Did you find any coins?

Thank you for posting this! Had to wash some kitty-soiled towels recently and wanted to make sure the drains didn't get gummed with litter and you-know-what-else. Got the agitator off and found that the drains were all clear! Your tutorial let me get peace of mind.

I have same washer shakes like a car wreck any tips +soaking wet clothes

Just did this, the bolt is super tight. Get a socket 7/16ths, then use a hammer and keep tapping on it counter clock wise holding the bottom piece with your thumb. Once it’s off. Banging it did not work for me, get two pair of channel locks, grab it in the center/ outside where the bolt center is. Rock it back and fourth and pull up. Only place to grab on it. Every port hole was filled with change. Use needle nose and screw driver to get it out

no dan repuesta

Well I can't get it out no matter what. It's really starting to piss me off. Lol

Anyone know how to remove the tub portion or know where to find a video of it? I need to replace the suspension rods. I have a 600 and very similar to the washer

Does anybody have a manual for this washer . I just bought a used one and not sure wen is right time to put detergent and softener in washer

That’s is bull shit

Do not buy this specific washing machine without agitator, does not clean clothes, I purchased It and within 3 days I returned It. Buy one with agitator.

Mines won't agitate

To tell you honestly, that f cover is not letting go so i put the f screw back on and forgot about me cleaning the wholes where coins and all of that debri is located at, so f that!!!

Hey cabj 185,I didn't notice which way the arrow in the tub was supposed to point to,does it matter ? Lemme know please ? Thanks bud👍🏻

What's causing a burning smell after spin?

How do you put fabric softener in this machine?

Thank you

Thank You🙏

I cleaned mine out and it still doesn’t spin out clothes all the way

Can you tell how to fix your washer when it’s off balance

I own this one and HATE this washer!! If this Kenmore 500 is meant to save energy, then why does it take a FULL HOUR to wash a load, even if only 1 pair of leggings? Awful! Also, this washing machine does NOT tell you which cycle it is on. Terrible! Finally, this thing does not get clothes very clean! Cringe! I have to use the freaking laundry matt when it really matters that my laundry comes out right! Not worth any money used and def not worth it new!

Thanks a million, problem solved👍

Hi, I have been jerking the tub up, wiggling the agitator & pulling on the agitator on my kenmore series 500 washer to no avail, do u think that some retained water could b causing the washer to jump & buck around? Thanks Richard

I wiggled and it ain't coming out.

Do you know how to fix the agitator if it stops spinning? Mine sounds like it’s grinding. Same make and model as yours.

I just watched this video and fixed my washer all by myself, had a bunch of change stuck in it!! Thank you for the easiest video to follow along too!!!

I struck it rich!! I couldn't believe the amount of coins stuck down there.....I am now a millionaire....thanks so much for your help.....

Leave the bolt halfway threaded in and tap on the head with a hammer while pulling up on the agitator. Mine was 11mm not 7/16s

Thank you so much, the wiggle part works and was the key for the Kenmore 600 Series as well (600s) specifically.

I wish you would have shown how you put it back together. Seems simple but did you encounter any difficulties?

Where's the filter

NOTICE there's nothing clogging those drain holes. Same thing when I took mine off. There was nothing clogging them either. THIS IS NOT THE RIGHT WAY TO FIX THIS WASHER''S CLOGGED DRAINAGE PROBLEM!

I need to replace the drive shaft that drives that agitator any idea what the part number would be

Very helpful video Thanks brother

This video was awesome. Able to clean the whole bottom of our machine. Do you know how to take the top off so we can clean the inside of the drum too?