To compute surface htc, you have to give reference temperature in reference values tab in setup...have you considered inlet temperature as reference temperature or whatever the default temperature value was in reference values ?

hello sir!! nice work.. I am new to this thermoelectric field. I have a doubt. Why did you give voltage boundary condition?? please tell me..

Sir can you please explain how to generate report from this

In this video how to get the plotting graph for variation of heat parameter and others?

Great

It is a good presentation, Because why are the inertial resistance and viscous resistance in the y and z direction great with 100 times than x direction?

If the gear is immersed in a fluid like MRF whose viscosity changes in the presence of magnetic field. How to simulate for the developed heat due to the interaction?

Please dont use background music

Better to use involute equation directly in spaceclaim as you have shown in one of your other videos, to get the gear geometry

I have a model of a heat exchanger can you help me doing a cfd analysis on it

Can you do a video on cfd analysis on parallel flow heat exchanger

can DPM be used to create still particle bed?

Sir how to plot time - temperature graph of this same

Sir, where i can get the information of CD nozzle physics and parameters for cold spray surface coating simulation to analyze gas flow and particle flow inside the nozzle

Sir I need to discuss something related to DPM with you . Can you share your mail address?

thank very much

overdefined dimession cannot be modified .. in case of Sketch 3

How to download this software please tell me

1st😎😎😎

Very good!🥰🥰🥰

Thanks a lot, really helpful!

THANKS IT REALLY HELPED A LOT

Why is the 'Form New Part' option not showing when I right-click on the solid? reference at 6:29 timestamp

sir can u please provide me the geometry

floatig point error

Thank you

Considero que usar el mismo mallado para tubo rugoso y tubo liso, no es correcto. Ya que el mallado depende de la rugosidad y condiciones del flujo. (Consider that using the same mesh for rough tube and smooth tube is not correct. Since the meshing depends on the roughness and flow conditions.)

Nice video! How can wall shear stress be generated in turbulent flow?

Thanks for this video

Sir can I have your mail address to contact you?

if similar this hot air transfer the heat to cube of wood ,how it possible?

have you any video related to dynamic mesh. i want to do flapping of a aairfoil using dynamic mesh

Thank you very much for the tutorial. I wanted to ask, please : when we were in the mesh stage In the names section, we were having, we were having inlet, outlet, fluid_zone_inner, fluid_zone_outer, plate_wall. Now we shift to setup : we go to the cell zone condition and made our setup. Then, we go to Boundary conditions and here is my question, from where we got all that : the contact regions, the interior regions and wall 13 and wall 14. ?? How they all of a sudden are created? This was my first question. My second question is what is mesh interface , I mean what is the importance or what does mesh interface specifically do ? I am new to cfd and I hope you have the time to answer please. Thanks again for the great tutorial

what is that stupid music :|

how to calculate heat transfer co-efficient in this problem??

sir thank you this Great video, how extract inp file

thank you for the video. I have a problem where ansys created wall at the rotating inner fluid so the fluid is not reaching the plate however it is circulating around the rotating fluid as if there is a circular wall. I tried to couple the walls of the rotating fluid with the fluid but it didn't work. Could you help in this regard?

why didnt you consider variable properties of air with respect to temperature?

Thanks

Thank you so much... Tutorial was very helpful😍😍😍

Hello, can I do Grid Independence Test In ANSYS Fluent Using Parametric Analysis with an Pointwise mesh?

Hello i have file directory issue and cant open wbpj ansys file . how can i solve this ?

Whats the need of patching?

Awesome, As usual dude Thank you so much

Is it possible to set heat flux? And what will happen to the temperature at the wall?

you have one of the best video channels for learning CFD through Ansys......Many thanks.❤

Why the split on select has to be used and what is mesh sizing ehat does it do

Can anyone please help me with the installation process of ansys fluent

Sir the videos are amazing but i hope you would have wxplained why you are taking the values in setup and so