Thanks, it worked. You can also reverse the normal of a region with a right-click on the respective region in the Model Info tree, and then click on 'Reverse'.

Would make a great grill tho ✌️ Right amount of wood, and correct fan speed.. Atleast in nature... But then again, flying embers makes is a Hazzard too... Idk, the biolite would be the best bet I guess...

Not sure if you ever found a fix. Like @bat_bat stated, it appears a white base coat is needed first... then covered with this 070 pearl paint. After my initial fail on a 2010 Toyota Highlander was trying to cover a grey primer with 5 coats of 070. It came out silver, not white at all. I switched to white primer and applied 11 coats of 070. Why 11 coats? Because 11 is one more than 10. In the end... the final result turned out a bit more yellow than the rest of the car. I suspect that's because of the large amount of 070 top coats I applied over the white primer... so it would be best to apply a certain number of 070 coats (like a tint) to achieve a good blend. This is hard to do because normally your work space is completely masked off so you can't see the reference points to the original paint. I'll try using some clear plastic with my next masking so I can still reference the Toyota base coat - and just apply 4-5 coats of 070. Best of luck out there, Toyota owners!

thankyou so much! i was very frustrated but nowim happy

Very helpful, I just changed my battery on the first try by following this video. I got my battery from Napa Auto for $260. Just some info for anyone trying this replacement for the first time, my new battery came with a little plastic adapter for the vent port (the last thing you disconnect from the old battery), so if you try and plug the vent port to the new battery and it's too big to fit, whoever sold you the battery probably owes you an adapter. It looks like a little 1 inch cube with a short tube coming out of it.

Thanks-super helpful!

That was easy except the positive connection takes a bit to pull off. Thank you

better watch the video at least at 1.5 x speed

More skating around the hard headedness of Autodesk.

Get an old diesel truck

It worked! Thanks, I had over 100 components, and this is an easy way to clean up my Fusion 360. Liked and subbed

man, why did they get rid of this feature?? so frustrating

Let me know if you’re ever willing to sell it! I’ve been looking for one for years hoping someone would sell! ❤

I watched your video and it was very helpful. Thank you very much. I bought my batteries at Costco for $214. They are group size S46B24R-AGM batteries. It was easy to follow the instructions from the video. Save me a lot on labor to install them.

It’s still too quiet.

Thanks bro!!

thank you.

it didn't work for me

Great video thank u. Do you have videos on the breakfast

I have a 2013 Prius that won't start. It's in a lot on a lift. I wish they made a key entry for the rear door. Someone is going to have to climb in in the dark and remove a large amount of stuff in my trunk to get to the battery. Terrible design. Who in the world would put a battery there?

Don’t you get chocked when placing the negative cable back to the battery?

Is your battery still working well?

Your ventilation duct is missing....

As @bat_bat mentioned this is a two part paint... you're never going to get a good final product by laying down the 070 alone. You need the 040 base, followed up by a good 2k clear coat. Do not use a clear other than a 2 part clear as you will never get the correct finish.

Do you have to reset anything in computer s system

Does not work

I came in here because I want to help someone who has the same problem as mine. Just recently my 2008 Prius went completely dead even after changing to a new battery. There was no life, nothing at all. I had to ask my friends to give me a jump. After watching many KZfaq videos I found out that one of my fuse was gone. When you open the fuse box, at the right under C section, there are two blue no.15 fuses. I changed the second one from the top. After that I also had to tighten up my negative volt battery which is in the trunk attached to the back of the car. Make sure you unscrew the negative volt before putting on the new fuse. After that it came to life. Hope it helps someone.

Dont you want to test the battery on the car before you put the mounts and covers back on?

This was an exact replacement for the old one that lasted about 10 years. kzfaq.infoUgkx7yWIKcrbA9KMHkGSfcgxW2lsjHT6B8Sh The top of my mitigation tube by my roofline was just a 90 elbow which allowed too much debris to fall down into the fan, eventually ruining it. Without this issue, I bet it would have kept running another 10 years. When I replaced this fan, I added an extra elbow joint so the top tube now it does a 180, which should solve that problem. The radon guys around here wanted to charge me a $300 diagnostic fee, then parts/labor (probably close to $600 total). I installed this all by myself in about an hour for the cost of the fan; it would probably be even easier/faster with two people. FYI the manufacturer's warranty greatly differs depending on whether you install it yourself (1 yr warranty) or have a licensed installer do it (10 yrs).

You did a great job. DYI is always frustrating but you learned and did it,

Thanks so much for doing this. Also, everyone else - get out a 10mm deep socket ;)

Even worse, the Dupli-Color white pearl's now appear to have defective nozzles. I just used two cans and they both clogged while actively spraying and threw paint drops on my body panel. I'm pissed.

just installed one of these today. the author of the video is not kidding about the vent pipes. they won't have them in the store and forget about elbows. we ended up getting a 5" sheet metal tube and a 3" sheet metal tube and rigging the double pipe setup ourselves. the 3" tube is your vent and the 5" is your air intake. It wasn't that hard, but it took a good bit of rigging to get it done. Fortunately for us, this was a first time gas appliance install, so when we ran the gas lines we just went with 3/4" all the way from the meter to the utility room.

Interesting tale, problems are always lurking in every project. I installed my Bosch tankless a few years ago and it had 6" concentric pipes, what a pain lining the holes up. I am looking at replacing the unit with a Rheem Anyway I have a couple of questions. 1. Rheem says your warranty is void if not installed by a "pro" so you have no warranty? 2. How did you get the 5" concentric piping, I cant find anything more than 3 feet long for $100 each?

Hi. Can you give an update on the satin copper? Does it patina like copper does or is it staying shiny?

Why do you install an optima battery and then refer to a different battery in Amazon link?

Toyota 070 is a 3 layered colour. There is a solid whitish first layer, then the pearl and finally the clear on top

These heaters need more gas volume, not pressure. Imagine trying to put out a house on fire with a garden hose. The pressure may be very high on the hose to hit the second story roof, but it's not enough water volume.

Where did you get the positive terminal attachment for the battery?

Thank you Toyota just told me $140 to put the new on in

Thank you. It worked.

This is terrible. My electric unicycle is a lower end model(kingsong 16s), and it can go up much steeper hills than this, and I weigh 230lbs(in the process of losing more weight)

Great

im reading that 070 code actually requires an additional color as its own coat after the 070. I think it's 040. After each of those dry as separate coats, you do the genuine Toyota clear coat or a pro aftermarket's closest version.

None of this works for me. How are you selecting a construction point within the 'Bodies' tab? Would have really helped me....

Thank you! Great, helpful video.

U still like it?

Perhaps you can space the kickstand lower by adding some washers, with longer screws to prevent the chain from rubbing?

I don't think this works anymore. Version 2.0.15050 x86_64