No you didn't, as this part was sent to me before release date! It didn't come with the adapter for the trx4m battery. I did test it off camera on the scx24 2s battery, and it worked perfectly fine. It had great modulation and some insane power and speed! Definitely less than with the 3s. But I did notice on the 2s if you change the dip switch, 27.2 volt for the servo it likes to cut out! So if you going to be running 2s I recommend keeping it on 6 volt for your Servo.

They do say it is for the 118 and 124 scale trucks, so I'm sure in the near future it will come with the mounting plate for the scx24 and red cat Ascent 18.

Good morning bro, it's a pleasure thanks for watching, and commenting 🤜💥🤛 No it does not provide the same torque as the 180 motor! It provides a hell of a lot more 🤪 It would be a great system for your IR 40 build, and yes the 180 motor if you still running the 87t it would be too weak to have enough drag brake! The purple 48 turn motor from enduro would be a lot better. But as you are using the 370 it's about the same as the 48t 180 motor. This has much better modulation, about the same drag brake as the 370 motor, and a heck of a lot more torque and speed. There is also a program available for PC and this brushless motor comes with a unit so you can connect it to the PC. In that program you can set your drag brake wherever you want!! Don't be in a rush let us all figure out the program and the best setups! But I am sure this would turn your IR 40 into the ultimate rig! 👊😉

I believe these are 63 mm by 24 mm, and they are the swamp stomper injora tire

Bro I'm not 100% sure because I didn't install the gears, this is the transmission I removed from the 6x6 chassis I bought on AliExpress. So I am really not 100% certain if it is stuck during or reduction gears. But I do believe it is the reduction gears. As soon as I can I will grab another transmission from injora with the reduction gears and check if there's any difference. Don't forget it is on 3s and that really does give it that extra wheel speed.

Bro for the price! I think it's unbeatable! It's so smooth and quiet! And then it's got some insane power and wheel speed! Great setup!

I am running to 63 mm by 24 mm swamp stumper injora tires 😉 They are still some of my favorite tires they make!

Thank you so much bro! I'm glad you found my channel and even happier that you like my content! Thank you so much for the sub bro. I do focus a lot on the micro crawlers, and will be doing some full builds in the next week or two. Cherokee Jeep build and a ir60 6x6 build. I really appreciate you watching and commenting, thank you 🤜🤛

Awesome bro, I am still waiting on the parts I ordered to do my Jeep Cherokee injora build!!! Hopefully it will be here today or Monday! The 9 mm hex drive I'm using is from injora, I highly recommend this little set as it makes it easy to get into those tight spaces. I've been using them for 2 years and only now am I starting to need a new set. For the price I think they really worth it, here is a link www.injora.com/products/5pcs-0-9-1-27-1-3-1-5-2-0mm-hexagon-screwdriver-hex-screws-wrench-tools

Good morning Jonathan, definitely I am really impressed with a lot of the parts that injora have released over the last year and a half!! I will definitely be using this system in the future for any of my builds. It's a bit late for the 6x6 and for the Jeep Cherokee build as I've already ordered all the parts before this was launched. But that's fine because I also wanted to test the new MB 80. The price is definitely much more affordable than any other system I have seen! Making it a viable option for us. All I can say is that you are going to love it 👊😉

This body was released last year by injora, they also have the IR 40, which looks like an FJ40 Cruiser, and they have just released the Jeep Cherokee body!

It's definitely a must especially for the price they are at! It's a pleasure bro, I'm the one that appreciates you watching, and always leaving a comment 👊😉

They do supply the adapter for the Traxxas TRX4m batteries, for some reason it just wasn't in the box they sent me. I have checked and they have confirmed, that it does. Performance wise I was very impressed.

@@rcfungames even better , now I have to get one !!

For the price tag and the performance gains!! It is definitely 100% worth it!! Now I'm waiting for a 110 scale brushless system 😅

Definitely the 3s battery has given it a lot more punch! I also ran it on the scx24 2s battery, and it's still performed really well and had a lot of power and speed! But on the 2s battery it doesn't seem to want to run 7.2 volt to the servo! On 3s I have absolutely no problem up in the power to the servo. It's a great performing system for the price! Which makes it a lot more accessible for the people out there that don't have as much cash! Like me!! 😅🤣

It came with a couple of adapters, and I see on their site that it's supposed to come with the trx4m battery adapter too. Seems like they didn't get into the box they sent to me. But it did have an adapter for the scx24 battery, and I did test it, and it seemed to work perfectly fine.

Thank you Andy, it's the first thing I thought when I was testing it! It's a great system for the MT monster truck 🤪 If I'm lucky in a month from now or two I will find a MT here in Portugal! 😅 At least I finally got the Ford F-150 trx4m.

Hello Andy it is great to see you my friend!! I have missed your comments over my last few videos! 😞 I hope you enjoy this one, thank you so much for the visit and comment brother! 🤜🤛

It is completely silent, it definitely doesn't screech like my Furi wagon. I tried to hear the motor and I can't At high speed all I hear is the gears. It's a very impressive system!

I did mention in the video that I am using a brass transmission with 40.3 gear set, which is the reduction gears. I will I just didn't have enough time as I was trying to get this video out as quick as possible. I will see if tomorrow I get out with the furi wagon and the jeep, so I can do some comparisons. Honestly I didn't find any drawbacks to the system, it is extremely smooth, quiet and has great modulation at low RPM. It also has an insane amount of power and speed on 3s. I do notice sometimes that it likes to shudder but it is barely noticeable. For the price I don't think we will find anything better.

Thank you bro, I really appreciate that mate! 🤜🤛

Definitely done I would recommend picking up a few of these! Insane performance for the price!

It definitely is bro, so far I only have one brushless truck, and it's the furi wagon, so this was an awesome system to test. Performance wise, it's definitely quieter, and has the same modulation, but I feel it has more power and speed! But that could be because the furi wagon is on 2s not 3s like I got this one is on. I really wish they would come out with some 1/10 brushless systems 😁

@@rcfungames definitely that's awesome brother

Thank you so much bro, yes I am running the reduction gears. And it got plenty of speed, and really awesome lowdown modulation 💯💯

I am running the low gears in the transmission! It's got amazing modulation and some insane power and speed!! All around excellent setup for the price!

Same here, I just ordered over 700 bucks worth of parts for my next two builds! And it would have been really nice to have used this system in them. But I guess it's too late now 😅 No it will not work with the light kit! The stock battery I believe they are including an adapter now! But if you wanted to run the stock remote you will need a Traxxas receiver. Hope that helps 👊😉

@@rcfungames Thanks a lot for your answer. Well. I do have two Defender builds. One to use indoors and one for the trails. I absolutely love what they are doing for the scale world and their quality is mostly superior. Anyways. I appreciate your videos and love watching them. Best regards. Edit: in this case I've to stick with the stock receiver unit because I have to have my lights 😂

@@Bonecrusher-ht1mh it's a pleasure bro, thank you for the support. I am exactly the same that's why I've kept my stock electronics, in my Bronco Defender and K10, and I just got the Ford F-150 finally!! And I will definitely keep the stock electronics and that one as well just because of the light kit! I love the scale light especially when I crawl around my course at night. 😅🤜💥🤛

It's awesome bro, I just went for a Dumborc combo from injora I use them all the time and once again it works really well with the system.

@@rcfungames thanks 👍

@@rcfungames is this model I can take : DUMBORC 6CH 6 Canaux 2.4GHZ X6PM-350 4.8-12V RC Mini Transmetteur

@@laurenthochart7605 that should work perfectly 👍

It really is impressive!! Especially for the price tag! I think it's 100% worth it 💯👍💯

Yes I am running a 3s battery, which I showed and mentioned a few times in the video. I also tried it on an axial scx24 2s battery and it works great! Also has great modulation and some serious power and speed! Of course with the 3s you have a bit more punch! 💯

Totally agree bro!! I had been waiting for this for a long time! It's a pleasure, thank you for watching and commenting 🤜🤛

Muito obrigado António, é uma excelente novidade de injora! Há muito tempo que eu tava à espera que eles saiam com uma sistema brushless, para os 1/10, e de repente saiem com isto! Espero que em breve haverá para os 1/10!! Fiquei mesmo impressionar com o performance deste sistema! Como sempre António Muito obrigado pela visita e pelo comentário 👊😉

De nada Amigo ❤ Forte Abraço 🎉

That's really funny, I actually need to pick up some of those! As I'm still running the original electronics in the Bronco Defender and high Trail! And it would be nice to customize the controller a bit. This is definitely an awesome setup! Why not do a full build, like that you need to buy a new controller anyway. 😅 And with this brushless setup it can be your ultimate rig 😅 Two weeks ago I ordered everything for the Cherokee Jeep build, and this system wasn't out yet, so I guess I'm still going to be running the 370 motor with the MB80. And for some reason it is taking a very long time to arrive! I really appreciate you watching bro and thank you for the comment. 🤜💥🤛

@rcfungames That's awesome though, very awesome! 💪🏼

Bro, it's awesome! I've spent my whole day running it! There's a few little things I've noticed but nothing that would stop me from buying the unit and fitting it to every single one of my trucks! It feels very similar to the system that the furi wagon comes with from Furitek. Definitely a great little system.

It felt like an eternity waiting for it to arrive in the mail! Injora was nice enough to send one out to me before it was released so I could install and test it and get a video up around the same time it was going to get released. Everything about the system is impressive from the price to the performance! Thank you for watching and commenting Patrick 👊😉

Well at least it's a much better price than Furitek!! Can I guarantee you it is worth it. If I ever make it on KZfaq!! I will send you one! Better than that I will send you a whole truck! 😅 Thank you bro and I also want to say thank you very much for watching and commenting. 👊😉

It is for sure wayyyy better priced than furitek. In my opinion furitek is a bit overpriced compared to what you get, especially when you can get that injora one for way cheaper which crawles just as well as furitek! And thanks for the hope of getting one😅 No problem and thanks for entertaining me and several others.😎👊

Thank you bro, that's awesome, retire this is my favorite part of a build! Finishing off the custom look. Thanks for watching bro 🤜🤛

Definitely bro this is an awesome accessory for the K10 and Ford F-150! I will let you know a little secret, I just picked up the F-150 so I can do a custom build as well, with that awesome Ford F-150 body 😁

@@rcfungames that’s awesome I can’t wait to see how it turns out

Thanks bro I thought it looked better than just those flat vents! I feel it gives the body more character!

Hi Peter, like I mentioned all the items used in the ir40 build, is in the description of the video. If you have any trouble finding it let me know, as I can always send you an email, with all the items and a link to them. Sadly enough they don't make a kit! But it is simple enough to just go through the items on their site and of course pick up all the items needed to do the build. That's how I do it.

Hello, as far as I know there's no kit available, but in the description of this video, you will find every single part used to make this build. The only thing you have to do is swap out the normal 4 millimeter extended axles from the list and replace it with the diamond 4 mm extended axles. Anything else, let me know.

Hey Ryan can we email ypu to find out the parts list for this build

@@petertyson4036 of course, my email is, [email protected]

Hello Don 👋 Thank you so much brother, I think it's turning out awesome! 😁

Bro! Thank you so much for pointing it out! I am so stressed out trying to get everything done and still work on the videos! That I completely messed up the title! 🤣🤣 At least I've got a subscriber, that's actually paying attention 🤜💥🤛 Thanks for the heads up I will definitely check out some of their accessories and see if I can order them from where I and based. 🤜🤛

Thank you so much brother I really appreciate it! It's nice to finally come to the final stages of each build. 👊😁

@@rcfungames yes always great to see things come together and work out

I definitely think the drill bit is the easiest solution, but more often than not those are the drill bits we always break! That's why I also showed the option of doing it with a lighter and a needle. I always end up using that technique as I end up breaking the drill bit 😅🤣🤣 Next time I go past the hard way store I think I'll pick up at least 20 of them 🤣🤣 I used to have an awesome electric screwdriver that had all the drill bits I needed, but can't seem to find it! Sounds like you've got a perfect setup to do this kind of job 😉

@@rcfungames I’ve broken a few drill bits myself. I need to get some more now I think about it!

I haven't really seen many videos fitting any of these accessories, and since it was time for me to finish off these projects, I thought I better get stuck in. They're not difficult to fit, it just all requires a lot of patience! There are a lot of little fiddly things to mess with that could be a lot easier. Especially that double-sided tape that never seems to be cut right! 😅 It's a pleasure bro thank you for watching and dropping some awesome comments 🤜💥🤛