used to use grade poles set by survey. front a back site then 5 feet down, shine light through steel washers. that was the 5 foot mark simple and fast as long as everyone on the same
@JoryDion2 күн бұрын
@@coderedcodered8161 I used the same thing in the track drift
@coderedcodered81612 күн бұрын
what is the temp in this stink hole? thanks
@JoryDion2 күн бұрын
@@coderedcodered8161 I'd say average 15-20 degree Celsius. 5 in the winter
@norandois7 күн бұрын
It can happen haha isnt easy jobs! Nice channel!😊
@andrenawej32197 күн бұрын
Vraiment I'm cuff
@edwinrosales563111 күн бұрын
Wooow! En mis 16 años como perforista nunca vi ese movimiento.. que maniobra!!!! Debes hacer un tutorial sobre esa forma de perforación .🤣🤣🤣 👏👏👏👏👏👏👏👏
@JoryDion10 күн бұрын
Shit happens 🤷🏼♂️😆
@trucktrailerparts17 күн бұрын
rock drill tools factory
@mamadoundiaye728219 күн бұрын
Great video we use 421 it posible to show us proper how to configure ?
@JoryDion18 күн бұрын
It is similar but not the same. the biggest thing with 421 is keeping stable rotation pressure
@mamadoundiaye728211 күн бұрын
@@JoryDion copy that and what is the difference between them and 420
@centre.line.mining55Ай бұрын
Great videos!
@JoryDion28 күн бұрын
Glad you enjoy
@curtisjones1904Ай бұрын
You'd think that things were the same all round but your bag is different from the DAMOS stuff we use in Western Australia - we don't have no hoops in the bag here. And you run your catenary wire different too - we normally tension it up by spinning a stubbie bolt in it and securing it with a couple of minsup clips, or in the old days an L Pin - you've got that flash looking plastic coated thing to do it for you - neat. Do some more video's you old hack - congrats on the 20 years thing ya old dawg!
@JoryDionАй бұрын
We used to use a stubby bolt but they need the minsup clips or some guys even use tape to keep them from unspinnibg . The plastic looking thing is coated in rubber and electricians use it to hang cable and clip nicely into the mesh. I plan on making some videos but as a trainer for the orange OEM typically it's other guys who are learning on the controls.
@curtisjones1904Ай бұрын
@@JoryDion Copy copy.
@maxtrac1Ай бұрын
I've ran a 100 hp slusher, In a iron ore mine. We had a lot of them on each level.LONG HOLE DRILLER.
@maxtrac1Ай бұрын
Put some teeth on that bucket.
@JoryDionАй бұрын
Ya that was like 20 years ago lol. Teeth would have been nice but not highest priority
@rouchevonplaster4945Ай бұрын
Drill Rig operator from South Africa here Hope you still drilling or shift supervisor by now Good work nice too watch some one els from different mines do it
@JoryDionАй бұрын
@@rouchevonplaster4945 I help drillers get better now and help mine's help their drillers
@user-oz4yw5ne2xАй бұрын
I love drilling but dont have experience , just certificates
@JoryDionАй бұрын
@@user-oz4yw5ne2x how do you have certificates with no experience?
@holdenv8cars748Ай бұрын
Got anymore video?
@JoryDionАй бұрын
@@holdenv8cars748 hopefully soon . Change of career path . Treading lightly until approval
@franzrojasluque47682 ай бұрын
Que pasa si te atasca el barreno en un taladro ?
@JoryDion2 ай бұрын
I won’t let that happen
@Papacon132 ай бұрын
U guys use screen pusher or just the good old wrench in the chuck
@JoryDion2 ай бұрын
Ya wrench in the chuck is usually all we have available..or I'll just use a longer steel and not bother pushing screen at all
@user-nj4no9py6p2 ай бұрын
Помню как работал с перфоратором😊спасибо.
@whitejtw2 ай бұрын
Thanks for sharing
@papabits57213 ай бұрын
All I have to show for using one of these is a bad case of white hand
@JoryDion3 ай бұрын
Gotta get the thick orange monkey grips. Also I try to not hold it as much as possible 😆
@zzINSANETYzz3 ай бұрын
I’m excited to learn the jack leg. I volunteer at a mine when I have the free time for an older gentleman and he’s teaching me the ropes. Next time go in is jackleg time
@JoryDion3 ай бұрын
Have fun and don't be afraid to get wet
@avo-autonomousvehicleorgan18993 ай бұрын
Fantastic videos and narration! We should connect as my company is building some phenomenal tech to improve efficiencies and safety of these headings.
@JoryDion3 ай бұрын
Send me an email
@taylorozbourne20523 ай бұрын
When I say I want to go mining, this is what I mean
@patrickguimaraes12873 ай бұрын
Nunca vi instalação de tirante manual assim hahaha... Apenas com equipamento Jumbo
@ScottHooker-nm3mp3 ай бұрын
Just an odd question but I drill sidewinders with booms and steel facing the cab instead of up and down. So my question it how do u put both booms in the cut? Should add tho that I’m using a 282 atlas copco any feed back is appreciated! Thanks In advanced
@JoryDion3 ай бұрын
That trick works for most jumbos . 282 is the same method .
@ScottHooker-nm3mp3 ай бұрын
Just an odd question but I drill sidewinders with booms and steel facing the cab instead of up and down. I So question it how do u put both booms in the cut?
@ScottHooker-nm3mp3 ай бұрын
Just an odd question but I drill sidewinders with booms and steel facing the cab instead of up and down. I So question it how do u put both booms in the cut?
@ScottHooker-nm3mp3 ай бұрын
Just an odd question but I drill sidewinders with booms and steel facing the cab instead of up and down. I So question it how do u put both booms in the cut?
@ScottHooker-nm3mp3 ай бұрын
Just an odd question but I drill sidewinders with booms and steel facing the cab instead of up and. So question it how do u put both booms in the cut?
@JoryDion3 ай бұрын
Swap the booms for the cut . Take the bottom boom and put it on top and the top boom and put it on the bottom so the drill steel of each boom is very close and right ontop of each other .
@ScottHooker-nm3mp3 ай бұрын
Ahhh ok I had thoughts of doing it never tried it yet but is there any issues with stinger pads being to close?
@JoryDion3 ай бұрын
@ScottHooker-nm3mp depends how tight you want the cut. Usually I’ll use the stinger pads to help measure the burden. Typically you will be drilling 43-38mm bits. Can afford to have your cut spread out more then old jack leg cut . For some reason the pads are to big you can just drill different holes at different times and they can still both be on the cut drilling at the same time
@ScottHooker-nm3mp3 ай бұрын
Hmmmm very true I’m gonna try what u said swap the booms… has to be better then one boom drilling the whole cut!
@JoryDion3 ай бұрын
@@ScottHooker-nm3mp absolutely I hate watching 1 boom idle
@Justinlendrum13 ай бұрын
What mine are you at I work at Creighton mine as a beat mechanic
@JoryDion3 ай бұрын
I travel around Canada helping the less fortunate.
@cohenp44petkovich4 ай бұрын
Should always put your screen first that way you won’t get kloberd
@JoryDion4 ай бұрын
I agree.
@jacklegminercanada38664 ай бұрын
Just as the nut cracked too. Lol, at least your using canun
@JoryDion4 ай бұрын
Ya it was time to send that one to the shop lol.
@weymarsmithtorressandoval4 ай бұрын
Que modelo es ?
@JoryDion4 ай бұрын
DS 411
@weymarsmithtorressandoval4 ай бұрын
De que mina es y la ciudad ? Por favor.
@weymarsmithtorressandoval4 ай бұрын
Buen video. Me interesa más los vídeo del ds411 el boltec pernador.
@ctman16814 ай бұрын
Can you please teach me how to connect the machine
@JoryDion4 ай бұрын
Air in the top water in the bottom 🤷♂️
@weymarsmithtorressandoval4 ай бұрын
Buenas tardes. Excelente. Tienes mas cideos. Me interesa. Opero boktec y proximo llegara un sanvick a la empresa. Me gustaria ver mas. Ya que en youtube es poco lo que hay de este modelo. Por ejemplo operar dentro de la cabina sobre las funciones de los joytick y demas
@JoryDion4 ай бұрын
I have some videos that show inside the cab. What model # are you getting ?
@franzrojasluque47685 ай бұрын
Excelentes videos, gracias por compartir tus experiencias y asi aprendo mi ingles minero, Muchos saludos desde Perú.
@christinespencer4065 ай бұрын
Wombat much quicker
@JoryDion5 ай бұрын
what's a wombat? Keep in mind I don't get a choice of what gear I run . I just use what the company has lol
@christinespencer4065 ай бұрын
Slow progress how much advance 24hours .howhigh is the coal is it long wall or boared and pillar 😊
@JoryDion5 ай бұрын
Not coal at all. 8.5x8.5 in most areas. Some.larger some smaller This is a hydro tunnel no coal in site
@evelynoppong35485 ай бұрын
Im a jumbo operator from Ghana but i use a single boom jumbo without screens. I wiuld love to use your machine one day. I use the DM801HDE from SANDVIC. Im impreesed wacthing you 😊
@evelynoppong35485 ай бұрын
Why don't you have any outsider to help you check your patterns? 8:37
@JoryDion5 ай бұрын
we are spread very thin. We have no offsiders or help. One man show
@mitchellmacdonald68975 ай бұрын
Do you with water or just air?
@JoryDion5 ай бұрын
Both
@mitchellmacdonald68975 ай бұрын
@@JoryDionI work for a shoring company, we're currently doing 3.3 meter holes on a 15° downwards angle. If I'm correct a jack leg is designed for flat drilling or upwards correct? 😅 It's literally killing my body doing this.
@JoryDion5 ай бұрын
@@mitchellmacdonald6897 no we do -15 or more even. For some help you can drill a steel straight down and then chain your foot to it. Then use the air leg retract button to help pull the machine out. Or use a steel ladder
@mitchellmacdonald68975 ай бұрын
@@JoryDion Im finding my mojo now, I'm also in a man basket 85 feet in the air, appreciate the insight, and be safe!
@erikgreer26245 ай бұрын
💋 *promo sm*
@ericm14305 ай бұрын
2 guys on a scissor deck with a few stopers is way faster IMO. Although I would much rather run a maclean lol.
@JoryDion5 ай бұрын
Expierenced MacLean operator will be drinking coffee and napping before you finish with 2 guys on a deck
@daveduplessis67446 ай бұрын
We used to do this in the 50s and 60s. In some parts they still do. We dont use winches for cleaning anymore
@JoryDion4 ай бұрын
Ya this is pritty old school for sure
@jg57866 ай бұрын
Recommend as a job?
@curtisjones19046 ай бұрын
Ugh. I've never been much of a hand at putting up vent but I'll tell you what I'm amazingly good at catching it on a boom or the roof of the cab and tearing it down. We all have our gifts :-)
@JoryDion6 ай бұрын
This is the best comment 😆
@dixienormous27046 ай бұрын
Glad to see you posting again! We've missed your underground adventures!
@JoryDion6 ай бұрын
Just old stuff I have recorded now from ages ago that I never released
@zachvoz12346 ай бұрын
What mine are you working at ? In Ontario ? I want to work at a mine like yours that lets you get away with this kinda jackpot work
@JoryDion6 ай бұрын
Lol this is really old. Jackpot work isn't good
@AndyRAK6 ай бұрын
This is why some people say “slusher knots don’t work” haha
@abkahvegi6 ай бұрын
I wanna see a stope mucking full cycle Jory … thank you
@JoryDion6 ай бұрын
That would be a cool time lapse. I haven't been to involved in any producttion
@yoshy40726 ай бұрын
You've become one very skilled miner, I dare say you could get hired anywhere.