Пікірлер
@miguelarmenta5703 Күн бұрын
Fixed the problem, bought 2 actuators and same problem, I opened the old one to see what was the problem and after studying the actuator, I saw that the contact pins on the black gear would barely get out of the contact board making the problem of not opening or closing. I rolled up small rags to zip tie them to the plastic rail on the blower motor where the vent door rest, set the actuator to the middle, installed everything back and works like new. (The rags stop the inlet door from fully opening so that the pins stay on the contact board)
@Zacpactv 22 сағат бұрын
did you reuse old actuators? glad it fixed your issues!
@toricastro147 3 күн бұрын
Perfect video!! Mine had a horrible rat smell! Turns out they nested up under the windshield air intake. Had to remove the plastic grille and got a water hose in there to get everything out of there. A little water made it in the cab, luckily rubber floor mats caught the piss water. I soaked the evap coil and intake ducts with green clean and will get after it tomorrow again. That’s what happens when you let your truck sit I guess!!
@Zacpactv 2 күн бұрын
Hopefully you get the smell out, rat piss is a terrible thing!! mine has been sitting… im hoping i don’t find anything ahhh
@joeparker7508 4 күн бұрын
Good deal bud thanks
@TheDillohead 7 күн бұрын
This comment has nothing to do with your current video, so I apologize in advance. But I was curious if you could help me with how you converted your kids sehomy tractor to a 18v battery? Thanks!
@Zacpactv 6 күн бұрын
No problem, you have to splice into the bigger red and black wire to make this work. I recommend using a knock off battery to the brand of adapter you install. The drills that these batteries come in have a resistor that keep batteries from being drained to 0%. So using your good batteries is not a good idea unless you an aftermarket protector. I would recommend watching a conversion video on youtube. The easiest way is to hard wire without a low voltage cut out. I would also wire an inline fuse to protect from a short which can cause a fire!
@TheDillohead 4 күн бұрын
@@Zacpactv thank you for the help!
@jonah9310 7 күн бұрын
Mushroom roots typically grow in rings, this is just nature being nature.
@Zacpactv 7 күн бұрын
A farmer leaked some round up i believe years ago it killed a spot then this happened. Look close you will see a “face” in the lawn.
@georgedavall9449 8 күн бұрын
You should make a finish/ follow up video on this, bro!
@mleukus 9 күн бұрын
so it is a year old - how is it holding up
@Zacpactv 9 күн бұрын
Im still impressed with it. I have 4 or so batteries that I cycle out. I have a chainsaw as well and plan to buy a blower. i have a play set, trampoline and fence to trim around. I would not recommend for heavy use but I trim almost a half acre yard with it.
@brianmills4891 9 күн бұрын
I was interested in the topic but got sick watching
@Zacpactv 8 күн бұрын
As did the rest of viewers ⬇️😞
@BobChanter 9 күн бұрын
Spit it out man.
@jdcohen7688 9 күн бұрын
You are the man! My vehicle popped up with all the images! Thank you so much, this was a very informative video.
@Zacpactv 9 күн бұрын
welcome! thanks for feedback
@PlumbNutz 10 күн бұрын
There's an abandoned truck just down my street and ironically the dash is perfect. Heading down there now😅
@nielstout7527 17 күн бұрын
Thank you for sharing this information. I'm dealing with the same problem tryna match paint for my machine.
@roberthammond4642 19 күн бұрын
What are you doing? You can’t get the pen to come out the slide the shaft out I’m having that problem with mine now.
@sa2ah0 20 күн бұрын
thank you for this my Dakota has horrible bedrock and I'm going to give this a shot I'm guessing thank you for this my Dakota has horrible rot in same spot
@Zacpactv 20 күн бұрын
Welcome, I see they have gone up in price just like everything else 😀
@mike2959 22 күн бұрын
Every wax ring that has a horn, when I remove the horn is cracked. Every. Single. One. And yes. Like all you guys, I’ve changed out a lot of comodes.
@silverdragontaylir8252 23 күн бұрын
Awesome
@drewmatthew3 24 күн бұрын
Thanks for the video. I'm cleaning my son's helmet too. I'll try the nail polish remover.
@warrenself 24 күн бұрын
Reminds me of a video of a truck that had a hung open injector.
@Toomanydamnchannels 25 күн бұрын
I just picked up some cub cadet paint at tractor supply. It didn’t look very close inside of the store but when I looked at it in natural sunlight outside of the store, it was a much closer match. Hopefully it’ll look even better once on the mower.
@tevanoff6754 27 күн бұрын
Great info,thanks.
@vspitta954 27 күн бұрын
I’m glad you got it for $10,000 less
@fotospaceto2425 28 күн бұрын
My dishwasher has a dog smell lol
@Zacpactv 27 күн бұрын
might try a splash of bleach 😅
@TheRealBTeich 29 күн бұрын
That my friend is a called the blower motor resistor module
@Rebel9668 Ай бұрын
Ariens is pronounced like Erins, not like Aryans. Hell, just watch some of their own videos.
@Zacpactv Ай бұрын
good info rebel!
@cammarshall2743 Ай бұрын
Mine is doing the same thing intermittently, but it blows black when you give it lots of throttle. Did you get it figured out?
@landenbenson7979 19 күн бұрын
Ever figure out the issue?
@presidentialcampaignads Ай бұрын
They actually never removed the mortice lock that part you were referring to is the mortice joint that holds the door together
@marcuswallace7613 Ай бұрын
I actually did mine last night and I use an orbital sander with a 40 grit sandpaper took it right off in less than 10 minutes. I had it done with no damage to the surface underneath.
@lightrider3435 Ай бұрын
Is tr 414 good for honda 125cc motorcycle
@Zacpactv Ай бұрын
what psi is the tire?
@lightrider3435 Ай бұрын
@@Zacpactv I think it's 42
@Zacpactv Ай бұрын
tr 414 is rated at 65psi max
@lightrider3435 Ай бұрын
@@Zacpactv we can use it right?
@Zacpactv Ай бұрын
I would always recommend metal valves for a motorcycle.
@COOL-517 Ай бұрын
I only watched this for the food and metallica
@m.weston7114 Ай бұрын
Use a dash cover. A guy that collects vintage trucks, told me to use a use a cloth soaked with transmission fluid and put onto the entire dash plastic twice a year. it does not need to be dripping wet, but apply it so it has a sheen to the dash. He had cars from the 50's that the plastic dash looked new because he did this to them. I do this twice a year, but wash down the dash first with soap and water, when it dries, then do this application.
@Zacpactv Ай бұрын
I may try that! Transmission fluid is very absorbent.
@frankie7508 Ай бұрын
The review is not very good because he simply doesn't know the difference in specifics between the machine. It's clear he did not do any homework before shooting the video. Don't waste your time watching it.
@Zacpactv Ай бұрын
One day I will get there! This channel is just whenever I get a free minute. Thanks for you’re feedback @frankie7508
@Zacpactv Ай бұрын
Hopefully you caught the main point they are near identical. very small differences.
@frankie7508 Ай бұрын
@@Zacpactv Yes and I agree with you. It's simply that I was looking for the minor specifics. I own a gravely 36 inch proWalk. And I am now looking at a zero turn. Any recommendations? One suggestion You might consider is to read the specification sheets on Each machine and then shoot your video as you walk around the machine pointing out the differences. There's nothing wrong with Having the specification sheet printed off in your hand as you go around the machine and point it out. It's called a presentation aid. After all we have an eighty year old president that can't even talk in front of his own press conferences without being directed and having aid sheets written down. So If the president can do it so can you!!! 😁 Take care and keep working on those videos!
@Zacpactv Ай бұрын
@@frankie7508 good point 😀 I would recommend anything hustler brand! This specific setup 50” deck has a horrible cut. No matter how sharp the blades are. I don’t know if the suction is poor or what but you can find others with the same opinion. With a simple google search on (why do gravely ztx cut so bad?) Kawasaki or honda engine on a hustler frame is the best in my opinion.
@UrbanExplorersX Ай бұрын
My vents up there are in perfect condition and I own a 02
@Zacpactv Ай бұрын
you are very lucky. They crack were the air flows mostly.
@user-kt5tz2wc2l Ай бұрын
you need to move your camera faster
@Zacpactv Ай бұрын
😂
@rondamon8004 Ай бұрын
Igot one and I like it...get familiar with the machine is the point..For the purpose it works for me, it's not a bad machine..
@Zacpactv Ай бұрын
Im sure everyone will have different opinions. It only worked good for small twigs. Branches it really struggled.
@mikehill1613 Ай бұрын
Thank you! Great tip. Much appreciated
@Zacpactv Ай бұрын
thanks! welcome!
@rodgerwilliams5604 Ай бұрын
How did you get the sun visor reinstalled? I’m working on my 2004 gmc sierra . It’s a pain trying to the holes line back up.
@Zacpactv Ай бұрын
three torx screws if i remember right!
@rodgerwilliams5604 Ай бұрын
@@Zacpactv do you remember having to pinch the tabs on the backside to get back into holes lined up right.
@rodgerwilliams5604 Ай бұрын
Hard to explain.
@Zacpactv Ай бұрын
@@rodgerwilliams5604 i do not remember having any trouble
@blainenaster Ай бұрын
Turbo failure?
@Zacpactv Ай бұрын
Was leaning toward cracked piston but did not diagnose.
@brandonedwards3216 Ай бұрын
Hang up on hangers while taking a hot shower to get the wrinkles out
@Zacpactv Ай бұрын
good point! Exhaust fan off 😅
@mariosolis9367 Ай бұрын
Hello, by chance do you have photos or video of the part where you remove the block since it is not visible in the video, I have the same problem on the same sprayer, I hope you can help me, excellent video
@Zacpactv Ай бұрын
I no longer own the sprayer but from what i remember it was very simple to remove block with alan head bolts. Also take off the prime/ spray knob. My rubber seal was blown!!
@mariosolis9367 Ай бұрын
@@Zacpactv I already did that, the engine sounds good, but I can't get it to press
@Zacpactv Ай бұрын
@@mariosolis9367 is it blowing any air with out hose or nozzel hooked up?
@mariosolis9367 Ай бұрын
@@Zacpactv No, it doesn't blow any air
@Zacpactv Ай бұрын
@@mariosolis9367 ok then the head could be plugged. you will want to pull it. the fluid will spill out if its tipped. I believe its just compressor oil. try to keep it all in.
@samizdat113 2 ай бұрын
Why does everyone suck their teeth while speaking now? So annoying.
@Zacpactv Ай бұрын
Good observation, maybe a millennial thing?? 😬
@KurtStevens-yi1jo 2 ай бұрын
I had trouble getting my Campbell Hausfeld to prime too. I ended just putting a hose clamp on the clear hose up by the block. What I think is happening is it is sucking air just before the block rather then sucking from the bottom of the hose. It is working now every time.
@Zacpactv 2 ай бұрын
I don’t have my sprayer anymore. It ended up being a rubber seal in mine that i replaced with a new one from a harbor freight kit. Sounds like you got yours figured out, hopefully that tip will help others.
@mariosolis9367 Ай бұрын
@KurtStevens-yi1jo Could you help me with a photo since I have the same problem and there is no pressure, in the video it does not show when you remove the block and what changes that is my question, thank you
@jorgeescareno6346 2 ай бұрын
Thanks this is what I was looking for thanks for your help.👍
@Zacpactv 2 ай бұрын
Welcome! thanks for the feedback.
@robertcampbell1343 2 ай бұрын
Do you think you could help me if you still have this mower? I have one I bought with a wiring issue...and I need to try to rewire the battery.
@Zacpactv 2 ай бұрын
Not in my possession anymore . sorry.
@ravender730 2 ай бұрын
ooh man you also have a Super Duty, could you also measure this one, also from the ground to bottom of the cabin? i'm really curious how much taller the Super Duty cab is compared to the OBS.
@Zacpactv 2 ай бұрын
I will keep you posted!
@safetcazimaj3006 2 ай бұрын
Where did you buy the 6x6 base ? I checked Home Depot and they only got 5x5 the reviews said that the size was wrong on Home Depot site
@Zacpactv 2 ай бұрын
Good question, the post base were already there and i believe they were just 4x4 base just to keep it of ground but have duty. I think the box stores cary them but if not here are some. bearhollowsupply.com/products/aluminum-plinth-block-use-for-columns-plinth?variant=43663330705659
@safetcazimaj3006 2 ай бұрын
@@Zacpactv thanks man I like these the most I want my posts to be off the ground too and look how good they did for you a lil bit makes a huge difference appreciate it
@Zacpactv 2 ай бұрын
@@safetcazimaj3006 anytime!!
@bonez6349 2 ай бұрын
I just pick one of these little jewels up a couple days ago.! This is a commercial mower btw... Idk how old mine is but im guessing its 20 years at least.? And man it runs like new.! Starts right up, no smoke, both gas tanks still work, doesn't bog down in high glass and cuts excellent.! The body on yours is in a bit better shape then mine but im am very pleased with mine as well
@TheCloser1 Ай бұрын
I believe the first two numbers of the serial are the year produced if you’re curious. I just picked up a 07 54 inch with a Kawasaki and I’m super excited to try it out.
@bonez6349 Ай бұрын
@@TheCloser1Well I was close.! I guessed around 20yrs old but according to my serial number its actually 22yrs old but it runs excellent still...!
@ravender730 2 ай бұрын
how tall is this truck? could you measure it please?
@Zacpactv 2 ай бұрын
about 27” from ground to cab corner. 79-1/2 from ground to top of cab.
@ravender730 2 ай бұрын
@@Zacpactv oh ok, on a different note, does that make the cab about 53" tall if we subtract 27" from 79"? living in EU, i've never seen an OBS in person, but i've seen a Super Duty in real life, just by watching these square bodies on the screen i could always tell they were noticeably smaller.
@Zacpactv 2 ай бұрын
@@ravender730 Yes 53” give or take.
@joseberriosbustamante9602 2 ай бұрын
To much Tokina blabla y no sabes by
@dennishall1933 2 ай бұрын
rebuild titles in michigan are orange stright titles are green
@Zacpactv 2 ай бұрын
i did find this out recently! I have now owned both green and orange
@user-wx6uw2dg4h 2 ай бұрын
Where is the link to your earlier disassembly video?😃