How long would this job typically take on a fiesta
@bormisha3 күн бұрын
Nice choice of music for the video!
@andyrantshumanphilosopher75717 күн бұрын
Wish my ryobi impact would actually undo nuts that are torqued over 70nm
@johnydepp833416 күн бұрын
Need answer please, is it ok to try two turn of crank ahaft before putting crank pully and cover on? just to check its in order.
@the-senior-tech13 күн бұрын
The timing bottom pulley is floating. Without torquing it up along with the front belt pulley you want be able to turn the belt and cams.
@georgegeorgel725417 күн бұрын
Hi.do u have to adjust the taps?
@andymcallister676224 күн бұрын
Wow ford really haven't thought about that the screen down low means taking your eyes off the road and looking down not straight like old one not sure what I think about interior need to see one up close mite be the thing that makes me move away from ford
@edisonschrader404626 күн бұрын
all to avoid adding a key, WTH
@ThePaulberryАй бұрын
Need a answer please. When tightening the crankshaft pulley bolt after 5he torque converter has been installed are the 90 degree stages at the output shaft of 5he torque converter or 90 degree of the input shaft (ratchet end)? Thankyou
@the-senior-techАй бұрын
5 times 90* through 1:5 torque converter gives you 90* turn on the crankshaft pulley bolt.
@ThePaulberryАй бұрын
@@the-senior-techCheers. I’m on it this weekend
@TommymcgurkАй бұрын
Hi around about 10 mins in What’s the grey sensor sticking out block ? Oil pressure? Thanks for sharing
@the-senior-techАй бұрын
Hi, yes, it is oil pressure switch.
@sara78130Ай бұрын
I have one tomorrow. Do it i do with out tool😊
@the-senior-techАй бұрын
Hi. No, you want be able to do it correctly without tools.
@AdrianJoldisАй бұрын
Respect! 👏
@the-senior-techАй бұрын
Thank you
@user-tb7fq5ov7bАй бұрын
How many litres of the oil? Thanks
@aelc4tdim858Ай бұрын
Excellent, just what i was looking for. Can i ask doses high pressure fuel pump needs to be removed for head to come off? Also ,whats the torque settings for head bolts. My engine is 1.6tdci ,for engine code t1db. Did you get your cylinder head pressure tested and skimmed. Thank you
@gabrirossi743Ай бұрын
I like much more the previous version
@HillaryKanyembaАй бұрын
Does that crank pulley have position sir maybe I missed that 1❤
@the-senior-techАй бұрын
Yes, it does.
@jjbermejodonaireАй бұрын
For god's sake that HAND BRAKE😅
@mariusc38599 күн бұрын
That made me stop buying this car. 2024 and they do that on a 25-30k car.
@kalexmmАй бұрын
Now I don't understand... In other video the guy said that injector that puts out more diesel in the tubes is the one with the problem, and here you say exactly the opposite. Which one is it? 🤔😊
@the-senior-techАй бұрын
It depends. You need to compare it to other injectors. In this case, the injector shows low overflow, puts too much fuel into the cylinder causing a typical diesel knock sound.
@kalexmmАй бұрын
@@the-senior-tech 👍 thanks for the reply
@848Evo86Ай бұрын
They ruined it
@joaoreis1079Ай бұрын
Someone got stuck in a moment… 😂 this is way much better looking than the half decade Ford Fiesta interior !!!
@rebeccaDimakatsoАй бұрын
They ruined the steering wheel 😂😂
@joaoreis1079Ай бұрын
@@rebeccaDimakatsothat I can agree with
@Mattey1Ай бұрын
@@rebeccaDimakatso Agreed & put climate controls on a touchscreen. Awful!
@blula8629Ай бұрын
Ich habe viele davon repariert die sind Schrott.
@michelantoniomorin2201Ай бұрын
Terrible engine
@monirmuallaАй бұрын
Amazing illustration ... thanks
@the-senior-techАй бұрын
Welcome 😊
@sara78130Ай бұрын
Thanks
@donideniro31852 ай бұрын
Hallo, erstmal gute arbeit, habe das gleiche bei meinen grand picasso 1,6 hdi gemacht, alles soweit richtig nur springt der nicht an dreht nur. Muss ich den kraftstofffilter vorher füllen ? Gepumpt habe ich es scheint das der kein diesel bekommt hmm
@the-senior-techАй бұрын
You need to bleed the system, ideally with a vac bleeder.
@RathanaSeth2 ай бұрын
I have ford tourneo 2018 chineses specs problem with BCM also .I have new BCM And now I cannot find the program to install in the new BCM . Would u help me?
@the-senior-tech2 ай бұрын
You need to use a Ford FDRS with a full accesss to IMO programing.
@toiletgaming20052 ай бұрын
i have to say after doing the same exact job on my 1.0 NA fiesta, its not nearly as hard as it first appears id gladly get a couple fiestas to fix my understanding is that using wrong oil degrades the belt to the point the coating wears off and starts sheading bits into the sump glogging the pickup
@lavina582 ай бұрын
Remove half of motor 🤮👎
@thyssmith12 ай бұрын
Why is my crank pulley moving when torqueing the bolt,do i need to have the locking pin in place.
@the-senior-tech2 ай бұрын
Yes, you need to pin it and use a new friction washer
@thyssmith12 ай бұрын
Found the problem,Crankshaft pulley washer and crank pulley was wet with oil,cleaned with brake cleaner and torqued the correct way.
@the-senior-tech2 ай бұрын
@@thyssmith1 Very good
@garycampbell52972 ай бұрын
Nicely done
@the-senior-tech2 ай бұрын
Thanks!
@tc32052 ай бұрын
Im doing same job, im struggling to get disc iff the hub and ive damage one hub bolt with e14 socket. Any advice?
@the-senior-tech2 ай бұрын
Gas torch.
@tc32052 ай бұрын
@@the-senior-tech i loosened it off but couldnt get the bolts off completely so i cut them and replaced it
@gulfrasta58442 ай бұрын
You have to take out the catalytic converter and high pressure fuel pump to replace the timing belt? Geez
@the-senior-tech2 ай бұрын
The cat needs to come off only if cleaning oil pump.
@Happyland3642 ай бұрын
Who designed this engine????😮
@the-senior-tech2 ай бұрын
😊
@wordtruth61162 ай бұрын
Incomplete job. No clear coat and final polish?
@jbleeuk2 ай бұрын
4:30 he puts clear coat on.
@the-senior-tech2 ай бұрын
Correct
@ajabdurrani59282 ай бұрын
Elite bro 🎉
@the-senior-tech2 ай бұрын
Thanks
@hagopsarkarian2 ай бұрын
People, beware of having this Ford's 1.0 Ecobomb engine when buying Ford car!
@ericrombouts76982 ай бұрын
When Ford had a better idea. Lost the plot now manufacturing utter crap
@user-gu5kk7wr5q2 ай бұрын
What in hell were Fords thinking when they decided to go this route to building an engine, what a nightmare this car has become.
@gerardper48272 ай бұрын
Let's get a Toyota instead , less trouble
@marcopinho31082 ай бұрын
What a nightmare!😅
@the-senior-tech2 ай бұрын
This timing belt is not that bad to do ;-)
@mechanictechnician92062 ай бұрын
@@the-senior-tech Hello, Mr. I need to call you by phone and thank you
@HkmsMommy2 ай бұрын
What size socket did you use to remove the rear mounting bolts?
@the-senior-tech2 ай бұрын
As I remeber it right, it was torx E14.
@spanky00h2 ай бұрын
You really didnt show how to remove paneling if never done before
@the-senior-tech2 ай бұрын
Hi. All screws are shown on the video unless your is early production and you need to remove panel around gear lever or at least move it away.
@maxwellfd23803 ай бұрын
Scrap it
@the-senior-tech3 ай бұрын
Saved it :-) New belt kit, clean up oil pump. Engine flush, oil + filter.
@maxwellfd23803 ай бұрын
@@the-senior-tech fair enough bro she sounded like a gonner
@MatthewBennettFPV3 ай бұрын
Did you use an impact wrench to get the bolts off the back of the hub?
@the-senior-tech3 ай бұрын
I used a long breaker bar.
@MatthewBennettFPV3 ай бұрын
were you able to access all the T14 bolts from the back with the same long extension? mine are really rusty and having a hard time.
@the-senior-tech3 ай бұрын
Yes, but also I used the swivel head adapter.
@AshLongie3 ай бұрын
Is the lower oil pressure belt changed at same time
@the-senior-tech3 ай бұрын
Yes
@atx-cvpi_993 ай бұрын
They should have put a chain in them to begin with.
@rodrigoramirez30373 ай бұрын
Great video
@the-senior-tech3 ай бұрын
Thanks
@arturlaukert6333 ай бұрын
Hi, is it possible to so this with Forscan?
@the-senior-tech3 ай бұрын
Hi, you won't be able to program an immobilizer with the Forscan. There is an option to do module installation/configuration but I never tried.
@MartinPohl4 ай бұрын
...and in your torque specs you talk about the 'wheel bolts' but you mean the wheel nuts setting correct?
@the-senior-tech4 ай бұрын
Yes, you are right. Corrected.
@MartinPohl4 ай бұрын
Thank you very much! Great video, good visuals!!
@the-senior-tech4 ай бұрын
Thank you
@stuartrowe43614 ай бұрын
Hi, is it ok to reuse the crank bolt and washer ? Ive just fitted a new and have to repeat the procedure as the pulley moved thanks