21 күн бұрын
3 ай бұрын
Пікірлер
@greenman7yyy 16 сағат бұрын
FUME: A respiratory irritant; small hot metal particulate matter as the result of welding. VAPOR: A respiratory contaminant; atomized gas, resulting from a liquid changing states to a gas do to temperature change or Venturi effect. Oh, that is most certainly NOT a 90 Bronco II. Regardless, not a bad sounding exhaust 😉👍
@theregoesmiller389 9 күн бұрын
WHAT HAPPENED TO THIS BUILD ? ? ? ? ?
@dustinmittel348 18 күн бұрын
Obs has the Australian headlights kit i hwve an 89 that been waiting for me to buy it a motor and have a few other things done 😢😢
@imartin6314 20 күн бұрын
What do you do to connect the rails to each other (extand the rails)?
@jangelsantana2266 22 күн бұрын
Lower the cage top so it doesn’t look like mega kind and extend it to the rear, nice fab skills and I’m a little butt hurt about the mint hood that just got bobbed but it was for a greater outcome
@jangelsantana2266 22 күн бұрын
What spring combination are you running in the Sam?
@TheRitchieLeeShow 24 күн бұрын
Terrific effort. I have recently seen an aluminum one that is too pricey. Might consider doing my own creation, now the ice is broken. I like the idea of ripping everything off that steel frame. 👍
@Oh6Torch Ай бұрын
How much does it weigh without the Hi-Jack? Thanks!
@MaddMango Ай бұрын
Moving right along!
@kdcarver Ай бұрын
I had a good alignment shop in my area replace the front upper control arms (bushings were cracked) and install new shocks (Bilstein 5100 with the adjustable leveling rings) a month ago for my 2011 F150 FX4. They leveled the truck, but It’s still slightly nose down, just not nearly as raked as it was from the factory. I then got new tires (Falken Wildpeak A/T4w replacing worn out Bridgestone Dueler Revo 2s of the same size) and had the truck aligned again to give myself a headstart on Houston potholes ( the camber is slightly negative). At low speeds and bumps the new suspension and tires are great but I'm disappointed in the highway driving performance. The truck requires a lot of driver attention to keep it on track compared to previously. I have to make small adjustments as if the steering is loose. It's tiring. Has anyone else had this issue when they leveled their F150 of this era with the Bilsteins?
@kdcarver 20 күн бұрын
UPDATE: After 3 alignments, a balance, and a rotation, it turns out the problem was with the Wildpeaks. Falken provided a concession and exchanged for a Bridgestone Dueler AT Revo 3 set. Exponentially better performance on the road. The new tires feel stable and firm without being rough. I'm impressed by Falken's customer service, but unfortunately, they need to work out some kinks with the Wildpeak AT4Ws, in my opinion.
@aired-downdisconnected4125 Ай бұрын
Nice 👍. So where is the 1st place your gonna camp in it ?
@malikdigger4544 2 ай бұрын
This Is Good Idea Especially When Living Off Road Grid Trails.
@bradleycooper5436 2 ай бұрын
I wonder of making a dash out of "pillow cushins." Foam and wrapped in aplosherty would would
@rheussy 2 ай бұрын
I built a camper out of the back of my 94 Bronco and camp in it often. I just found your channel and I am impressed by your work. I can’t wait to see the finished product.
@rylanhess1662 2 ай бұрын
Looking forward to seeing the finished product
@rylanhess1662 2 ай бұрын
Rad! I actually watched your vide just for learning how to attach the drawers to metal instead of wood.
@logibrown7411 2 ай бұрын
Really love the seat covers need to get some for my truck. Where did you order them from?
@MaddMango 2 ай бұрын
Looks great Jake! Did you ever consider in-floor storage boxes near the side door? I always wanted shallow storage, maybe 6-8 inches deep, just for light stuff? Seemed it would have been a great addition for quick access dry storage for the mundane things one might need to get to quickly. Looking forward to seeing your fender buildout and remaining work.
@Legacy4x4andOffRoadYT 2 ай бұрын
I did consider in floor storage and ultimately decided against it due to my time constraints on this build. You can most certainly do it if you have more time. The way I built this the mattress sits directly on top of the floor and eats up all of the available space. If I were to do anything under it I would have to move the mattress every time to access whatever is there, and I did not want to have any more external doors than I already have for ease of waterproofing. That front storage box that I built in is very large and has plenty of room for stuff and I am planning on making some organizers for it to make access easier. The rear sections will have three easy access doors for coolers, batteries, and camp equipment. We will see how it does during this trip and there may be some modifications on future builds.
@MaddMango 2 ай бұрын
@@Legacy4x4andOffRoadYT Yes, your front storage is gi-normous!
@Antdogg566 2 ай бұрын
The cove is horrible
@Shadowfletch 2 ай бұрын
How far does that center tube come past the 8 foot trailer base? It looks like its around 3-4 feet? so 11-12 foot tube? Thanks
@Shadowfletch 2 ай бұрын
Also do you think I could use 1x1 with both sides at 45 as gussets instead of the plates? I dont have a plasma cutter 😓
@Shadowfletch 2 ай бұрын
With a sharp enough turn (90 degrees) do you have to worry about the back of your vehicle hitting the angled tubes attached to the receiver hitch?
@Legacy4x4andOffRoadYT 2 ай бұрын
Hey the total center tube was 12ft long, it is an 8ft trailer and a 4ft tongue which I found to be the best for the size. You can certainly use 1x1 to make the gussets not necessary to use the plate like that. Honestly those plates are probably overkill especially if you follow along with the rest of teh build by the time you get all the uprights in and everything else this trailer is very very rigid. I am not worried about jackknifing while towing, with a four foot tongue there is plenty of space to turn about. Of course with any bumper pull trailer there is always a risk of that but it is far more common during reversing than it is during normal driving.
@Shadowfletch 2 ай бұрын
@@Legacy4x4andOffRoadYT Really appreciate the response. I'm doing almost an identical build and am looking forward to watching yours progress!
@aired-downdisconnected4125 3 ай бұрын
Be careful when sealing your TD. Ya dont want it 100% sealed. People have died in their sleep . My cargo trailer has 1/4" gaps in the rubber gaskets around the door's. Enjoying the build. 👍
@Legacy4x4andOffRoadYT 3 ай бұрын
thank you I have heard of this, I am installing a fan on the roof to cycle the air, and there will be a sliding window on the main door that will be bale to slide to create a little cross flow through the trailer. Thanks for the tip!
@glenbarnier 3 ай бұрын
looks awesome man, i might use some of your design on my truck
@Legacy4x4andOffRoadYT 3 ай бұрын
Great! I love the look of it
@MaddMango 3 ай бұрын
I'm not a welder. When I built my 5x8 I went with a sandwiched wall design. 1/4" interior plywood, 1x2 internal framing with 1/2 solid foam between, and 1/8" exterior skins (all construction adhesive bonded and screwed). Super light weight side and top panels. Fiberglass and resin over exterior for weather protection. I think my trailer came in at just around 950lb empty. I really need to learn to weld. A note on your galley hatch, I hope you have better sealing success than I did. It was a bear to achieve. I wish I had gone with just a simple square and flat back, provides easier sealing and a larger "awning" for the galley. Great work! I think you'll want windows on both sides for cross ventilation, but I'm in Florida and we have slightly different temps/humidity here.
@Legacy4x4andOffRoadYT 3 ай бұрын
I strongly considered that type of design but ultimately decided this would work better for me with my skill set. Thank you for the tip on the rear hatch, i think i have a plan for sealing the hatch but time will tell. And for cross ventilation I defintely considered adding more windows and I put the steel in the frame in case I want to add one in the future but for now I am going to be doing just one window on the door and the fan vent in the roof. I will mostly be camping in the Northern US in VA/PA and out west in Wyoming/Montana
@russellmccullin5797 3 ай бұрын
I tried to hit your website to get the full parts list but the site has expired. Is there an updated site? Thanks, I really like the build.
@MaddMango 3 ай бұрын
60/40 rule, I built a 5x8 off a HF 4x8 trailer. It had a rear kitchen and I just moved the axel to 1/3 the length. It towed fine.
@Legacy4x4andOffRoadYT 3 ай бұрын
Thank you! That was what I ended up going with, just shy of 60/40 and though I havent hooked it up yet it feels very stable on the ground and can easily wheel around my yard.
@LockItOut_Gaming 3 ай бұрын
Tear Drop trailers rule
@nateanthony4140 3 ай бұрын
💯
@Legacy4x4andOffRoadYT 3 ай бұрын
Thank you Billy
@johnhardison2044 4 ай бұрын
Not a bronco 2
@Legacy4x4andOffRoadYT 4 ай бұрын
Sorry yeah this is a full size bronco not a bronco 2
@MaddMango 4 ай бұрын
Nice! I think 5x8 is the perfect size. What height were you planning on? The way the center tube ends in the rear, you planning for a rear receiver on the trailer?
@Legacy4x4andOffRoadYT 4 ай бұрын
not planning a reciever tube in the rear at all, it could come in the future though. The trailer will be 4ft total tall. Well in practice it will be 47in tall
@masonloganpaving9988 4 ай бұрын
What size inverter?
@Legacy4x4andOffRoadYT 3 ай бұрын
2500 watt
@shahbazkh2885 4 ай бұрын
Good job 😊
@Legacy4x4andOffRoadYT 4 ай бұрын
Thank you so much 😀 i am very happy with it so far
@MrGsxr10001 4 ай бұрын
holy cow... you painted with no resperator ? this has to be a joke
@Legacy4x4andOffRoadYT 3 ай бұрын
probably shouldve but i am outside so cest la vie
@MrGsxr10001 4 ай бұрын
Man I get you didnt want do do the body work but dam... you really need to ask someone how to spray pait LOL
@Legacy4x4andOffRoadYT 3 ай бұрын
never said i was a professional
@davidcraft4909 4 ай бұрын
that is interesting, I actually thought of the same thing. to put a bead around the pipe to form a bulge or whatever its called to help keep the hose on. I don't have a fancy machine to roll that in there. but im still not sure if thats the way to do it, lol.
@Legacy4x4andOffRoadYT 3 ай бұрын
it worked! Thank you for watching
@DeeOutdoors33 4 ай бұрын
That rear end pinched
@Legacy4x4andOffRoadYT 4 ай бұрын
Very
@user-qj8nm5jn6r 4 ай бұрын
What stapler did you get
@Legacy4x4andOffRoadYT 4 ай бұрын
Just a cheap one off of Amazon
@ORD251 4 ай бұрын
That turned out great!
@Legacy4x4andOffRoadYT 4 ай бұрын
Thank you!
@zorsts 5 ай бұрын
looks great. nothing wrong with a few exposed pipes and hoses.
@Legacy4x4andOffRoadYT 4 ай бұрын
It works haha! No complaints from us
@BigTimTravels 5 ай бұрын
Lol they are not Chinese. They are made in Colorado 😂
@gamepassgamer3755 4 ай бұрын
Chinese parts 🙎
@Legacy4x4andOffRoadYT 3 ай бұрын
colorado made then
@gamepassgamer3755 3 ай бұрын
@@Legacy4x4andOffRoadYT fair enough I was just poking I own a 22 950 hoex
@singletrackmarc819 5 ай бұрын
What rear axle did u go with
@singletrackmarc819 5 ай бұрын
I'm building an 01 1500 right now and can't decide if I should keep the 9.25 or go ahead and swap it
@Legacy4x4andOffRoadYT 4 ай бұрын
This has the stock rear axle
@hottamaleboy1198 6 ай бұрын
Where can I get your parts list. Can’t get on your website.
@Legacy4x4andOffRoadYT 4 ай бұрын
We are in the process of migrating websites and will have it up on the new one and our etsy store very soon
@Granola8Lavender 6 ай бұрын
This is bad ass ! I have the same problem with my truck how much would youncharge for a job like this
@Legacy4x4andOffRoadYT 4 ай бұрын
You would have to be in the northern virginia area and it would be based off of the time it takes to recreate and the condition of your current dash
@nitrofreakmanho 6 ай бұрын
Nice work! I just bought some Scion FR-S seats to put in my FJ. Did you get any airbag codes after you finished? Thank you so much for posting this video, it gives me a little hope that I might be able to get this done. Are you a member of the fjcruiserforumD0Tc0m by any chance? You become an instant hit if you explained how you did this much needed mod, and where/how you placed the weight sensors on the passengers seat to bypass the OCS module. It’s great that you got it done!!
@hottamaleboy1198 6 ай бұрын
Can I use 2.5 x2.5 sq tube with these brackets
@Legacy4x4andOffRoadYT 4 ай бұрын
You can but it would be very tight, the brackets are meant for 2x2
@travisbenefield7087 6 ай бұрын
Nice one! Is that gun fire I the background at the end?
@Legacy4x4andOffRoadYT 4 ай бұрын
Yes this one was built while I was at Fort Benning
@newlifeadventures3632 6 ай бұрын
Love it! Are you taking orders? I have a 95 Bronco it would look great on.
@Legacy4x4andOffRoadYT 4 ай бұрын
I wish we could! but this was a custom one off build that i do not have any designs for sorry
@GWrench9 6 ай бұрын
Looks great! I have a 97 3500 12v and always wanted a Longhorn brown leather interior. This looks like the closest I can get without breaking the bank.
@Legacy4x4andOffRoadYT 4 ай бұрын
This worked out really nicely and looked great too!
@lynchcreekmuzzy5759 7 ай бұрын
Your welds look nice and solid.....i know its been a couple years, but do you recall what settings you used on welder for doing that 1/8th thick steel? Gas 75/25? I want to do this project, but with a dump bed kit on my 96' Cummins and do not want any blowout on the steel. Anyway, if you remember... good video 👍
@Legacy4x4andOffRoadYT 4 ай бұрын
Yeah this was done with C25 gas, so 75/25 normal mig welding gas. I do not remember the welder settings for volt or wire feed though sorry
@stacyreid5077 8 ай бұрын
The Bronco is coming along extremely well, I can’t wait to see it finished
@Legacy4x4andOffRoadYT 4 ай бұрын
Thank you! I will post a full walk around pretty soon, it is pretty much done at this point
@education292 8 ай бұрын
Hi there, I'm Azad from Bangladesh. I was analyzing your channel. Your vedio quality is good. But vedio title,tag, and description are not SEO friendly. Your SEO score is very poor. That's why your channel is not growing. As a professional marketer i suggest you to do proper SEO to get more views,likes,comments and audience organically. thank you
@Legacy4x4andOffRoadYT 4 ай бұрын
Thanks for the tips
@education292 4 ай бұрын
@@Legacy4x4andOffRoadYT i can grow your channel bro
@malikdigger4544 8 ай бұрын
Your forth gen Ford Bronco going be one fun rugit off road camper.
@Legacy4x4andOffRoadYT 4 ай бұрын
It is a great vehicle! Sadly I will probably be selling it soon due to an upcoming move