Dose every one use rit , and not Keda ? And why

Music is making me nostalgic for the Carnik Con OST

Elusive? 😂😂 There's at least 12 of them for sale on MidwayUSA...

Any recommendations on sizing? How would they compare to Nike for example? Thanks

Artwork!

Is there a hogue rubber grip that will fit? Of what is the Closest pistol grip that can be compared with the evo s2

Fine job buddy

I like these boots, but the soles wear out too fast for me. I'm really hard on my shoes and boots because I'm outdoors darn near every day. These boots are bulletproof except for the soles. I'd like to figure out how to resole these.

I noticed your stock with the metal plate. The C-93s come with a plastic stock without the metal plate. Did you modify your weapon to fit the stock with the metal plate?

Could I send you some to see if you could get them to work ? A reply would be nice .. thank you

Great video! This seems to work on Magpul Cz Mags as well. I got mine seated in the AKV but haven't fired to test ejection yet

Two tips. To remove the safety lever, pull the trigger housing back to where it stops on the receiver, it will come out easier. 2nd tip, and this is just my opinion, for the trigger group push pin, place it in from right to left. That way when you release the mag, you won't push the pin out if you miss the mag release.

Beautiful piece! Wish the sights were different, though.

I put one if these on my scorpion. I run mine with a binary trigger and an 86° angled foregrip. The handuard lasted 400ish rounds and then the piece that holds the washer started pushing back and cracked off. Litterally pulled the handguard off. Because eif how thin that plastic was. It was great, but it didn't last and am very disappointed.

Excellent review, Just ordered that same version with 6 extra mags and a Holosun 510C. Should be a blast banging steel. Been wanting an AK based 9mm to go with my RRA LAR-9mm for a long time.

CAN YOU RUN TWO CHARGING HANDLES? I changed mine over BUT want to Run Both Sides! WHAT IS THE RETAINING PINS SCTUAL NAME? I can see it being a necessary item to have SPARE! (Part# would be Great too!) Thank You!

Nice I just picked up the 1911A1 Tank Commander from tisas

Even though this is 4 years old I use of all things WD-40 it eats the cosmoline up I use a 2in. paint brush and brush the cosmoline off and then wipe the gun parts or magazines off and beat part won't have to worry about the parts to flash rust.

Good shots of the parts and handling as well. Thanks for clarifying the bolt assembly. I wound up using a silicon cloth to rotate the bolt with gun-slick hands.

Thanks could get my slide back in

Incredible video in my state is hard on this magazine i cant get another mine got smashed when i was moving wish u had extra 1 to sell

Hi can I contact someone about this product

Ty the dingos slowed me down😊

bout what my dodge sounds like

Sorry but stopping all business with NY companies. Not going to contribute to communist states.

Thank You for this

That's Some Nice AK Furniture Sir Salute You 313 Until I D-I-E 💯

Does the outer parts (finish) of the gun need oiling?

Why doesn’t mine fold???? I hate this shit

Do you recall the amount of rit dye per 3 colors you used for your mixture?

I enjoyed listening to Dwight Yoakam explain how to put the hand guard on!

Best combat shoe/boot for the money. Wore the crap out of mine and they are still going.

How much would that furniture set run?

Reassemble video after this would be helpful.

❤❤❤

I thought gen 1s had the two rods on the bolt? And the gen 2 is the single rod and spring?

You only half disassembled it wtf

Free pro tip for lining up gas blocks on AR's. Use a piece of spaghetti noodle that is just small enough to fit into the gas port but not too long that it sticks out of the top. The tighter the fit the better as far as diameter is concerned. Install gas block with the rifle sitting normally, flip the rifle over so the piece of noodle will fall into the gas block when its lined up. Tighten screws down and flip the rifle back over. Use a cleaning rod to break the noodle and both pieces will come out of the barrel on its own. They sell "alignment tools" that are small brittle pieces of plastic that do the same job.

Nobody knowing about the "dingus" issue for reassembly tells me that nobody reads their pistol manual that comes with the gun. Doesn't build my confidence in the gun community...

What is a meer

Have you shot the 9mm and the 38 already, do you just need to change barrel and mags? Or do you need to swap more internals?

Want semi matte finish, use medium steel wool, circles.

What should the length of pull be?

PURTY🎉😅

You paid Promag to make their magazines correctly. If you have o "work on them" you got taken in. I end up throwing my Promag C93 magazines in the trash.

Awesome video. Nice AK and thanks foe showing how you mount the pouches. (I have the r1 clips on similar belt, it moves from up to doen easy, need to find workaround)

I love CZ scorpion 💪🏻🇨🇿

Are all US importers of turkish guns now spelling turkey that way?

I know this is an old video but it is entertaining to watch when gun snobs try to nit pick the newer Taurus pistols. Most average shooters that will buy this gun will never notice the reset on the trigger or care.

Oh no the Romanian gypsy child who assembled your rifle made a mistake. Oh heavens I hope you were able to move past this tragedy