krazyk86cu

Пікірлер

@fedup1480 2 күн бұрын

So if you go into settings you can select the mode you want the exhaust to stay in. There is absolutely no need to pull a fuse unless you just don't know how your vehicle operates.

@krazyk86cu Күн бұрын

This is incorrect. The ecu will override your settings depending on idle and rpms. Pulling the fuse means the valves stay open. Period.

@fedup1480 17 сағат бұрын

@krazyk86cu well I own a 2016 z06 since new and I have exhaust set to track mode and it's loud, always, period.

@short5stick 2 күн бұрын

if you over tighten the oil filter cap you can crack the cooler housing.

@krazyk86cu 2 күн бұрын

Are you talking about the fuel filter housing or the drain plug? Couldn't find any actual torque specs for the filter housing so I just snugged it good. On camera it looks like I'm cranking it down harder than I actually am. You can feel when it's properly tight.

@short5stick 2 күн бұрын

@@krazyk86cu oil filter cap. I think it's 10 Newtons or something like that

@garyuk761 2 күн бұрын

Do you mind me asking what you do for your income

@krazyk86cu 2 күн бұрын

Not at all. I’m a pharmacist.

@junurensungkai2176 5 күн бұрын

is it posible install at Jeep grand cherokee 3.6l 2014 ??

@krazyk86cu 5 күн бұрын

You would need to purchase a kit designed specifically for your vehicle. I’m sure they make them.

@wpotc 7 күн бұрын

How can they just cancel like that without any notification? Especially if your insurance was paid in advance. You could probably sue them if that was the case.

@krazyk86cu 5 күн бұрын

They dropped my full coverage to just liability so they didn’t completely drop me. Regardless, if it’s not illegal to inform the insured it should be. If I had been in an accident and then found this out you better believe I would have been taking legal action. I’m sure they’d just lie and say they did notify me though.

@notw333 9 күн бұрын

THANK YOU!! I have the exact pistol. Cannot wait to custom it out!

@RandomVelocity 10 күн бұрын

I heard it’s a nightmare to put this thing together though instructional videos are horrible instructions that come with it are horrible. Some people said it took them four hours just to put it together other than that. Looks like a great idea once it’s together.

@krazyk86cu 5 күн бұрын

It’s not that bad. If you grew up with Legos you’ll be fine haha. I loved mine.

@RandomVelocity 5 күн бұрын

@@krazyk86cuyeah well it’s definitely the best solution I’ve seen

@angelvelazquez8493 10 күн бұрын

I owned a GT3rs and is not working for me.

@krazyk86cu 5 күн бұрын

I’m fairly certain the RS has different door handles right?

@Jbarb777 10 күн бұрын

Good job man

@Warrengr89 19 күн бұрын

She needs to stay in the kitchen

@bama509 23 күн бұрын

Need to remove the oil filter first to allow oil to drain down into the oil pan from the oil filter housing since it’s a cartridge oil filter.

@MrEricBeast 23 күн бұрын

Installed these today. Key thing is the short fat socket to lock the spring in the bracket to a bent position. Skip the zip ties and leave one stud nut loosened on one end. You can get the brackets in place without removing the rubi rails. Leave the socket in place until the step is attached with pins, socket comes right out when step is depressed 👌🏼

@joemalicki3504 23 күн бұрын

so you can replace the batteries without screwing up the computer???

@krazyk86cu 22 күн бұрын

What do you mean?

@SageParie-kc3lx 24 күн бұрын

Nice vid

@TheMuskyMafia 25 күн бұрын

Man that engine noise worried me till I seen it in every cold start video on these bikes 😅

@jannick-halben 25 күн бұрын

Is there no KingPins (pins) to inspect ? I also noted it has no pad-key stainless clips as the T&C have & the rear pistons does not need to be turned in with your tool, just pressed in & maybe out for easy seal-ring replacements. I was thinking about shifting my 11 ø300 to 14's ø330mm 2 pistons in the front. But now i will check if possible to get Pacifica Calipers seems better tobseevice and probably better anti-hanging

@ericmed 26 күн бұрын

FYI there should be a bolt with a label that is specifically there for grounding (usually on driver's side)

@TravismillerII 27 күн бұрын

G wagon

@dave11686 28 күн бұрын

Nice

@DarkTouch Ай бұрын

there is a ground post for the negative connection. use that. its on the driver side of the compartment and is labelled as a negative terminal. its on the pillar that the wiper system is attached to. also, better to use just a trickle charger to pop the bonnet using the fuse box connector, you don't need to use a jump box. this connector is not a fuse by the way, it is a positive terminal to power the hood latch. lastly, the LifePO4 battery is not likely "dead". it is just sleeping. The battery has internal circuity that protects it against excessive discharge which puts it to sleep. it just need a little kick to wake up. if your battery is truly dead, you will need to replace it. if you attempt to jump a truly dead lithium battery, you may start a fire. call for service/tow. you can use another car to jump the car as long as you use the negative terminal post and not the negative battery terminal. you can also charge it for at least 10 minutes with a lithium ion capable trickle charger.

@krazyk86cu Ай бұрын

Appreciate the advice. However, I do not believe a trickle charger will work for popping the bonnet. Even the instruction manual says to use jumper cables and a car battery. As far as the battery being “dead” I agree that was the wrong term for it. I figured saying dead would make more sense to most people and show up better for people searching what to do. In reference to the pop out terminal for the bonnet, fuse didn’t sound right but I wasn’t sure what to call it. lol I need to update the video, but it did end up requiring a jump to “wake” the battery. Really appreciate the tip about the negative post. I overlooked that. I’ll see if I can annotate with the correct terms in post. Cheers!

@user-vw6mu8gt6c Ай бұрын

You are misleading people. Please read the manual. Rear skid were installed wrong. In addition, you should always keep control arm same length. Because left right corner bear different weight, the hole won’t align unless you lift pinion a little bit. By adjusting the length, now you have a bad thrust angle.

@krazyk86cu 29 күн бұрын

Let me preface this with saying, this was over 2 years ago and I no longer own a Jeep. With that said, I am rewatching the video to see what was done incorrectly. Other than me playing around with the control arms, how were the skids in the rear installed incorrectly? As far as my control arms however, the original shop that installed the lift never properly torqued my control arms I believe that likely had something to do with my issues installing these, though I could certainly be wrong. I am by no means a professional. I don't recall how long after this, but eventually I had a more competent shop go over my entire Rock Krawler lift and tweak and torque things correctly. If those nuts on the control arms were torqued at the correct specifications, I never would have been able to adjust them lol

@arthurrodesiler3109 Ай бұрын

You put the H7 battery in and it only takes the H6 battery. H7 is to high.

@krazyk86cu 29 күн бұрын

I don’t remember which auto parts store as this was over a year ago, but I bought battery they told me to buy based on the vehicle. Didn’t occur to me to just take it back lol

@JavierGonzaleziii Ай бұрын

can you lift the TLP with the top on to give you more clearance for the hood?

@krazyk86cu Ай бұрын

What do you mean? As in adjust the pins on each side of the base? If that’s what you mean, then no. You’d need to set the top back on the Jeep and then adjust the base higher. If you just mean grabbing the release lever and cranking it higher, then yes

@karensalley4776 Ай бұрын

Thanks, you do a great job, probably the best how to video I've seen.

@erichendrick3928 Ай бұрын

What? Won't penetrate? Like Hell it won't !!!

@pascalmascarenhas5409 Ай бұрын

thank you for a very informative video.

@krazyk86cu Ай бұрын

Glad it was helpful!

@pascalmascarenhas5409 Ай бұрын

Had no idea that you had to go into settings to change the pads!

@dtdyeulnc Ай бұрын

Is it the same process for the front? Thank you

@krazyk86cu Ай бұрын

For the most part, yes. You’ll need some sockets rather than the hex key though. I’m not sure of the size as I haven’t replaced the front pads myself yet.

@bryanboldt887 Ай бұрын

Brilliant. You tried to stuff a H7 DieHard battery into a H6 slot. Gee, wonder why it didn't fit?!

@krazyk86cu Ай бұрын

Ya live and learn!

@dennisakkurt Ай бұрын

where did u get the tow kit ?

@krazyk86cu Ай бұрын

Bought it from a Land Rover dealership. Called around to a couple places and found one nearby that had it in. They even gave me a break on the price rather than charging a mark up like some other dealers I called were.

@HaiNguyen88888 Ай бұрын

Very nice 👍

@user-zx8nu5mx2d Ай бұрын

Your in Vegas and this is what you did lollll

@krazyk86cu Ай бұрын

Correction. We’re in Vegas and this is one of the many things we did

@EmmaBRIMFIwaa Ай бұрын

that looks so cool, but if I were to go up there I would be dying bc I'm so scared of hights.😂

@krazyk86cu Ай бұрын

When you are outside it is unreal! My buddy Travis wouldn’t get close to the side haha

@alexdan8371 Ай бұрын

My friend, you should start with traction off and from 3k rpm to get proper result, holding both pedals together

@blackstallion681 Ай бұрын

Thank you for the informative video! It saved me a lot of time and effort. I'm not used to working on anything newer than my '99 Cherokee, and all the extra stuff on newer cars is a little baffling at first glance 😄