The question is, for how long did the engine run before the NATS (Nissan Anti Theft System) shut it down? The K12 was a really nice car apart from the stupid electronics and official prices of parts after a weird and dodgy 'association' with Renault and the closure of several original Nissan plants in Japan with thousands of lay offs of skilled workers.

This was the BEST! THANK YOU!

Thank you very much. You are a legend ❤❤

Yaris, Il Piccolo Genio! Grazie.

Hi. I have a Ford Focus 1.8l 2007 Flexifuel and when i try to accelerate it starts to jerk and loose power and when i stop it dies. Sounds really bad from engine. When i start it again it dies directly. When i start it again after that i start to give it gas but it sounds bad and almost no power at all. But when cold it’s fine. What could it be?

Always change the water pump as well when doing this job. It will only come back and bite you on the bum

kzfaq.info/get/bejne/Y9iVjMl-rNnPaKM.htmlsi=QFsnm3pRwBD_DCCk

I was looking up mr2 ps racks and your channel came up and it was definitely the best video I’ve seen so far also your video on classic fest Galway I see a familiar car @16:26

very good video, thanks man!

thank you ! great video

The wrong way to put the seal 😵‍💫😵‍💫😵‍💫👎👎👎👎 they will have leak 100%

are the parts interchangeable from other Hondas

Great video, but you can use the large screw as a puller for most half-shaft joints (as well as this one). You just have to screw it in until you have pushed the joint down. No hammering and no risk of damaging the joint.

Una gran ayuda conocer el procedimiento. Gracias por tomarte el tiempo de filmar

I need to replace the dumper of the power steering, do you know if I can access to it from the top part? That would be much easier than remove the steering wheel and all the connections from the bottom part

Just did this. One point that might make someone's life easier - just remove the starter key barrel altogether. It is held to the steering column with one bracket and 2 flat head screws - undo those while supporting it (it is heavy). After you detach it pull it aside just enough so you can access the screws on the ignition switch. Replace the switch and put the barrel back pone - should be done in about 10 minutes tops.

is 12.5 ohms low?

ill try to do this one.tnx for the idea

I have the same issue but water is in the rear seat, but front all dry so is it the front grommet ?

Great job. Can you tell me the oil wrench size/part number for the oil filter? thank you

A uszczelki pod kolektor nie zakladales? Pozdr

Made to look very easy. A pillar passenger side is impossible to put back for me!

I am very grateful for this video. I watched it probably a dozen times while replacing my seatbelts. It was very helpful. Thanks!

Can you share the link of the relay from Aliexpress?

Does the drum often need replacing?

Thank you so much for the video! That little note that you need to pay attention to the color of the filter is so valuable. I bought filter with the black cup And the light was on. After I put sensor from the old lifter to the new one and boom! The yellow light is off. Thank you so much

Best EVER Video. simple and easy explanation. cheers

Hi, my car makes far more noise then this. My 2012 original pulleys will be replaced this weekend, thank you posting this video that I watched long ago and now using for reference 👍. I will also be replacing the belt tensioner, belt and pulleys, I'm not sure if the two idler pulleys are right hand thread or left hand thread, do you know? My manual doesn't have any info. Thanks. Rich

Thank to this gentleman I already changed my car pollen filter whiteout pay any pounds for it, Nissan says that will cost me £190.99 , to regas de a/c system, new filter and stuff , but I said , so what if I do it myself, and yes i did it 😅

How did you fix the gasket ring leak I’m having a nightmare with mine as the new ring was just as bad

Great video very informative... What a lovely car the Lexus is, by all accounts the is 300h is super reliable. Personally, I'd have it all day over the German competition.

Thanks for the video. It helped me a lot today. Just under 5 hours smh :D

what a horror! i have to go through all this i have the same car and i need to replace exact same parts! never ever i will buy a vw again, thanks for your video.

Thank you for the video. Good job.

3:25 can you tell me what the connector is for? the one right above filter cap? the mech that changed my filter and oil forgot to put that back, then i had loud chain noises and when i put it back it was fine. i just need to know so i can slap his face with info. My guess is its connected to the vacc and crankshaft position sensor. but idk..

Thank you

Merci pour ce tuto. J ai pu refaire ma clim

Thank you

Thank you!!!! ❤👍👍👍👍👍😊

Merci pour la vidéo, je ne parle pas votre langue. Mais les images sont très claires !!

This video make me realized that the first peace of plastic is missing from my car! Don't know the reason and who blame but is a peace you could not notice easily missing. Thank you for the instructions although

why not show that the sound was gone .. ?

There's a heat shield by the intake stopping you lifting it out . One bolt. It's not on the car when he lifts it out. Hope this helps

AH! thank you so much. I will try first thing tomorrow!

What's the timing belt part number and how many teeth does the belt have?

Excellent video and works, thanks for your great effort for sharing.

What about the lower part? I need to access the fuses and relays but cant reach them. Could you perhaps show on a new video how to take off the lower panel?

You make it look så easy.

Thank you for sharing this video, just fixed one car because of this 😍🥰

Hi is it possible to take the plastic cover on top of the mount? You have to torque the bolts no?