Ай бұрын
Ай бұрын
Ай бұрын
Ай бұрын
7 ай бұрын
Пікірлер
@GiginMathew-j3l Сағат бұрын
Wisper cage is good
@maurosotelo5509 13 күн бұрын
Hola señor como esta? La verdad que es una excelnte explicacion!! Disculpe la molestia hay algun curso para hacer de valvulas posicionadores me podria dar infornacion xfavor entre a la pagina donde dise curso pero no me deja entrar
@ahmeddinsajjad2261 24 күн бұрын
❤
@faiyazkhanahmad8736 Ай бұрын
Best explanain
@banyatniyomvas Ай бұрын
Thank you
@SLAUGHTYBAUDFAUST 2 ай бұрын
I think I heard something about a prize but I couldn't hear it because those shirts are just too loud.
@Travlinmo 2 ай бұрын
I am confident the award would have been disallowed if they knew you were going to wear those shirts.
@FisherControlValve 2 ай бұрын
Well played 😀
@Travlinmo 2 ай бұрын
@@FisherControlValve I hope they are all that and a box of chocolates… I am asking for a lot of them in my plant upgrades. No funny disappointing me.
@bhavikdalsania4297 2 ай бұрын
Hello Thanks for useful video. Can you please make video on pneumatic C1 controller for valve .
@user-zt4oj9ip3o 2 ай бұрын
Are 2-3 year old array kits still being used if so what are they worth
@user-zt4oj9ip3o 2 ай бұрын
Are 2-3 year old array kits still being used
@user-qt6ve8qk7y 2 ай бұрын
Prof una explicación de válvulas de gamas compartida
@Bataviaish 2 ай бұрын
Do you have video about calibration Control Valve with pneumatic controler, I want see it...thank's
@saidiramzi2470 2 ай бұрын
Is it recommended to install a strainer upstream the control valve to debris from clogging the cage??
@Time4yes 3 ай бұрын
Why are you only using direct acting valves? How about reverse acting?
@ahmedberchil4226 3 ай бұрын
very interesting.Thanks
@braideng8069 3 ай бұрын
Just add some sort of air sep device on it to suck in air on neg pressure
@bonifaceuzoma8938 3 ай бұрын
My observation, when the valve was travelling up the line in the magnetic array did not meet with the down line in the alignment template. Wunt this have issue during calibration?
@josemanuelalogoadjomo7863 4 ай бұрын
wonderful video, just wondering whether there is a complete course on positioners offered by EMERSON and if there's who can I apply to??
@Practical.instrumentation 4 ай бұрын
How we'll distinguished between bench set and operating rang ?????
@dave78x 4 ай бұрын
huh?
@andrewbarker1937 4 ай бұрын
where is part 2?
@yordanprado509 5 ай бұрын
THE BEST!
@benildz17 5 ай бұрын
I want one.
@randomstuff7045 5 ай бұрын
Watch your fingers!
@gastonithoua5439 5 ай бұрын
Je pense que le DVC6200 est plus efficace par rapport à ce 7K
@moslimalking8619 5 ай бұрын
Can you send me the link i need this program please 🙏🙏🙏🙏🙏🙏🙏🙏🙏
@moslimalking8619 5 ай бұрын
I need this program please can you send me the link
@medotedo8410 6 ай бұрын
"Wherever there's a restriction in flow, the decrease in pressure can cause a fluid to reach its vapor point" I think that is not reasonable phrase. The restriction of flow comes with increase in pressure not decrease of pressure !
@bitterwords3398 5 ай бұрын
When the area of a flow is narrower, its velocity increases. And the relationships between presure and velocity are inversely promotional. So any time you see a drop in the area of the flow, you see an increase in velocity and a decrease in pressure.
@balajiarni 6 ай бұрын
1 Year - No Instrumentation Engineers commented on such video, I really surprised. Majority of interview has this question from Standards of Valves
@Practical.instrumentation 6 ай бұрын
I'm facing issue with this type of positioner After calibration out put from positioner is not stable Valve begin hunting No solution is available
@alexmerit1414 6 ай бұрын
You guys have an actual Fisher and you almost don't use it to explain how it works
@syedaslam2856 6 ай бұрын
I'm bit confused when the standard signal input is 3 to 15 psi what is this 5 to 15 psi
@abhinikam105 6 ай бұрын
What is pipe diameter . And what should be the unit , mm , cm ?.????
@fredison1991 6 ай бұрын
wow
@GlidingBoulder 6 ай бұрын
cool.
@GlidingBoulder 6 ай бұрын
neat.
@GlidingBoulder 6 ай бұрын
E-Z.
@GlidingBoulder 6 ай бұрын
Very Nice
@user-nl2dq4me1u 6 ай бұрын
Hello.thank you for video. I have a question. Do we have to only use Cam A for beam alignment or we use other Cam (A or C) for beam alignment?
@aamirabbas7093 7 ай бұрын
Great news by Emerson
@djoudjou1214 7 ай бұрын
I liked your upscale page posts
@SamA-xu9gy 7 ай бұрын
Why does pressure drop in the globe valve?
@shashankgamanagatti965 7 ай бұрын
It's a great enhancement of IoT connectivity to valve sector 👏.
@asarafalimomin2811 8 ай бұрын
Please sir make a video about replacement c seal .
@vinsaggarwal9064 8 ай бұрын
ad yen helidi no yeno tilillilla,
@vinsaggarwal9064 8 ай бұрын
sike guru neenu
@ahmedsharaf578 9 ай бұрын
Thanks
@garymceuen5069 9 ай бұрын
At approximately 1:44 of the video, the K1 equation is used. d (nominal pipe size) and D (internal diameter of pipe) are used. d is shown as 3 (the nominal pipe size), but D is shown as 7.98. Shouldn't D be 3.068 inches? Please explain.
@ducbinhhdu 9 ай бұрын
Please make a video about Calibrating a Fisher C1 Positioner, thanks!
@josephksung 9 ай бұрын
Thanks