The video was very helpful. Managed to replace the impeller without any trouble. Thank you!!! Best regards from Croatia

Thats awesome i just bought the whaly 370

make sure you get the outlet tube lined up correctly or no water pressure, there is a grommet on top of the rubber connector hose that must fit securely, had it happen, dont rush .

might have done the first step with the motor tilted up , good video

thanks for this super informative video! I am trying to disconnect the power unit from the midsection so that I can replace my cracked driveshaft housing. But after removing the 6 bolts like the service manual said, the power unit won't budge and not loose at all. Any ideas?

I have the same motor, trying to remove the engine block but after taking all 6 bolts off it doesn't move at all... is there anything else I need to remove first?

Just the right amount of dialogue.

Is it normal for a small amount of water to come out of the plug where u connect the shifting rod together?

Dankjewel!😄

Ik kan me niet aan de indruk onttrekken dat die boot met een hoosvat of emmer een stuk sneller leeg zou zijn. Minder leuk, wel veiliger.

Het aan elkaar vastzetten van de schakelstangetjes blijft een raadsel. Nieuwe sparepart gekocht maar zit geen schroefdraad in het ene blokje. Hoe krijg je de 2 messing deeltjes vast op elkaar? Voor de rest bedankt voor de demo.

top filmpje. wel wordt er erg veel vet verspilt op delen die dat helemaal niet nodig hebben.

Jammer dat je niet uitlegt wat je doet en waarom.

Ciao, potresti dirmi il peso di questo fuoribordo? È anno 2004/2005? Stavo cercando delle indicazioni dato che ne ho trovato uno pari al nuovo e volevo acquistarlo Ho già un 3.5 cv portato a 5 cv con Elica in alluminio + carburatore maggiorato Però questo andrà più forte avendo una cilindrata maggiore

Hello, I have a Suzuki 9.9 motor so I replaced it with a Benio, but it still feels bad. I want you to find a solution, thank you

Bez młota nie robota

그냥 PE 재질인데 너무 비싸서 구입을 안한다. 그리고 자연 배수도 안된다.

Hola me gustaría ver un video como se desmonta la carcasa de la transmisión del suzuki df6

Great video, thanks! Funny thing, as I watched you work that shaft into place, I thought to myself, I'll bet that isn't easy. Then I read the comments. LOL

This man is fuel Efficient at the table 🛠️

Duidelijk geen technische achtergrond! Zo iemand zal ik nooit aan mijn motoren laten sleutelen. 😮

Wat een prutser 🙈

What’s wrong? Can’t talk English? Would be nice to hear what you are doing.

merci pour le partage

Does anyone know how to fit a tachometer to this engine

Great video! What's the white grease that you're using?😊

So you did not use any new gasket? Thank you for video.

Sure wish you had not cut out the part between 15:05 and 15:06.

What kind of grease? Was that a new housing too?

Well done showing how it was done. Even removed the key to clean inside of it . Thanks for the demo. Now I know how to replace my 15 horse 4 stroke Yamaha.

Great video. What is the white grease you are using? I am about to replace my impeller, but have never done this before. Thank you.

Great video! Really helpful for a motor imbesil like Me 😬

he must be deaf, thumbs down for no narration.

Does the motor spin clockwise when look down from the top?

Ну нафига снимать как откручивать и закручивать болты? Полезного из ролика одна минута.

Thanks for providing this information. A very well done video. I watched this as I impatiently wait for our local marine to get my Yamaha done. 🙄

Sorry for my question ..... Was that the right impeller ? The new one was like a star with straight lines instead of the old one that was like waves....

I just reassembled my motor. As so many others stated, the biggest issue was getting the drive shaft back into its seat in the engine. After several failed attempts, I used a thin, straight metal rod and a flashlight to see that there is a sleeve just under the fly wheel that the shaft needs to get through. First try and by gently feeling it through as I fed the lower unit on, it clicked into place. Gentle tug on the starter cord and it fit right in. Also, I had it in what I thought was reverse, but turned out to be neutral. Adjusting was easy by using pliers to push the shift rod down after loosening the brass clamp in the side, then shifting to reverse, and tightening back down. Thanks again for the excellent video!

Is it same for 2022. DF6 model?

Berapa harga 4pk bos

Beste Locomotion Watersportteam! Bedankt voor deze zeer nuttige video. Geen oneindig lange aftiteling. No-nonsense die je niet nodig hebt. Alleen de belangrijke informatie gepresenteerd in een zeer slimme context. Echt geweldig. Ik wou dat alle video's zo waren! Heel erg bedankt en veel succes voor jou! Met vriendelijke groeten, Lui

Very nice. NO vocal needed. Clear instruction.

By far, the best video I have seen! Great job, God Bless!

Tengo un motor 2.5 Yamaha 4tiempo. Le puse todo correcto el sistema de refrigeración, prendo el motor en baja revolución coje buena agua aceleró a toda máquina y deja de cojer agua

Perfekt. Dankeschön

You need a silencer for your ratchet !!!

I'm having problems with the same engine... I'm going to take the entire pump housing/assembly and throw it as far as I can.. "high" pressure pump... What nonsense. 38psi lol.. I'm going to fit an in line pump off a car and do away with all this mercury crap. Thank goodness Yamaha had something to do with building the engine or I'd just burn the damn thing. I'm getting tired of the problems these engines have. Mine hasn't even done 100 hours..

What brand of grease used??

One added note, great to have motor up higher like he does here. I missed that front bolt and thought the lower unit was stuck on the power unit. Anti seize on all bolts, lithium/dielectric grease on rubber parts during assembly. Great video overall.

Amigo requiero una bomba completa Mercury 4hp Precio por favor Aldo falcón Venezuela Estado Lara Barquisimeto