Do you use a normal mortar for tile on top of the red gard? Or a special one

Would you recommend the same test for a leaking shower where the tile is already installed and grout has been applied?

Dude I totally needed this video b/c I couldn't figure out the straight adapter needed to connect the water filter to our separate water faucet! Thank you so much!! 👍🏽

So did you spend $99 or $47 for you r DIY? Your Link shows ot at $101. C'mon, seriously? You couldn't find a hack for that? Or is this really an advertisement?

I wouldn't use Redgard on any showers. It's known to re emulsify and bleed pink through you grout joints. If you use Aquabar first you won't need to waterproof your shower other then the pan but get that hotmopped, that's the best way to go. If you really want to get down, float your shower with concrete. I floated all my showers until I got too old but then I started using Denshield. Score and snap, way less labor intensive.

👍🏽

RedGard needs to pay you, seriously.

Good way to get some exercise!

Does it filter flouride?

I wish this video had come up as a result the first time I did a search for a KZfaq video on electrical switches. 👍🏼

Very helpful vid. I found myself checking the wiring in your video having to replace my old State set-limit thermostat with a new adjustable top thermostat. There were wiring variations based on the thermostat manufacturer. If you could have shown the wire color a little better (lower) I could have confirmed my own wiring choices.. I think? Thanks again. Headed under the house with the multi meter. Peace

You deluted RedGard 1:4 to pre-prime. Do you delute it for main layers?

Never seen such a complete, detailed, and useful video about using RedGard. This is exactly what I was looking for for weeks. Thank you very much!

Is there some thing for redirecting a ceiling bathroom vent? My room is next to the bathroom and I'd rather push the air from the bathroom vent into my room. So a duct will be attached to the ceiling vent into the bedroom (leave the door open a bit to allow the duct in)

If you own a SDS-Max Rotary Hammer drill get a ground rod driver and it's a piece of cake. (No water needed.) If not a fence post driver can make it a lot easier than using a hammer, for most of the length.

Thank you!

This trick can be helpful: To avoid the weight pouch getting stuck or snug up on a branch make sure you either use a weight that can be metal or magnetic before throwing it up. You can also place any non-metal weight in the pouch and put a magnet inside the weight pouch. With this trick, if the weight pouch gets stuck, you could use a longer pole with a magnet at the end to pull the weight down. Viola!

Me watching this after I spilled water Everywhere lol

I’ve ended up hiring someone with the big machine to do it for me, got beautiful cuts with hardly any chipping

Very helpful, thank you.

thanks, this is super helpful. Opening that stud will change the way roof load is being handled, you probably need to add a header and an extra support to compensate.

Im installing a fiberglass shower pan so I'm only going to add enough water to cover drain test plug. Advice ?

You're the best at many projects ,especially electrical. I've been watching all these guys who say they're electricians and they leave so much out of theie projects. Don't stop.

Excellent. I'm dealing with cutting just a few porcelain tiles and opted for the angle grinder . I like the idea of scoring the tile first

or just get the correct driving tool

I like your barefoot shoes 😊

i think you mean Winter

You have to just hit it not push it down

great video! You will gain subscribers in no time. Does Red guard work with plaster and lath wall or is it best to replace that with cement board or other? Thanks.

glad i dont have to adhere to some over protective code bs

Very interesting, always room to learn and improve…👍🙏✅

Hmmm Thanks a lot

Thanks Dude

How do I find what motor is mine(the model number and brand)

Dude. Rent a trencher. It’s worth it for that distance.

Need to fill in the void around the box extender also. NEC 314.21. Gaps around boxes that are recessed in noncombustible surfaces (such as plaster, drywall, or plasterboard) must be repaired so there will be no gap greater than 1⁄8 in.

Thanks buddy.

What about single line faucets? Will all the water come out filtered?

I'm using what looks like the same curb as you. However, I am pouring my own pan liner with a membrane. I was planning on wrapping my curb in a thinset pasted concrete board like I found another KZfaqr do. sticking the concrete board to the curb using thinset is to avoid putting any screw holes in the pan liner when it wraps over the curb. Do you see this as a good idea?

Great job on the tutorial very informative.

How did you transition the conduit thru the shed exterior wall? I'm also running my subpanel on exterior wall between studs and need to come thru wall with conduit.

Thank you I appreciate your insite. I've decided to buy one of these for some high up branches on my property.

What is the size of the toe kick vent?

Lots off different suggestions and techniques to get that damn first string/ rope over the branch , all good ideas ! What ever works 👍 mine was I used string that masons and carpenters use for setting up straight lines and edges. …… ( didn’t buy it, had it from my working days) it won’t break ever! It is rated at 1500# test line. You’ll cut your fingers off before it breaks Any way I tie it to about a 1” or bigger socket which makes a perfect throwing projectile but that is in the hand of my son-in-law, my arm and little league pitching days have long since passed. Other than that I never saw the rope saw technique before, pretty cool 👍 Just a little trivia question for you, does anyone know how they got the very first string/ rope/cable over the Niagara river so they could build the bridge…? ………………….. Kite😉

What if the motor is working fan is turning well but doesn't seem to suck any steam out of the bathroom everything was cleaned etc ...? 🤷‍♀️

Seeing your niche trowel handle full of mastic drive me crazy. Also when installing schluter since is small using a margine trowel works way better also you didn’t polish your cuts that drive crazy as well.

I`ve seen some people dig a hole and use salt and carbon around the rod is it nessesary

Good info 🙏

When it comes to rules regulations and permits of your homeowner and you’re fixing this yourself and you’re an American I don’t understand why as a homeowner any of this stuff applies that the people say, in the comments remember if you don’t meet minimum code and ain’t, nobody’s fault, but your own And just because there’s rules for license builders doesn’t mean a homeowners can’t just works what works for them why does Americans keep doing this pushing their will upon others

Thanks !