Well two things are happening. The wrong fluid doesnt work with your tranee causing this code. Bad timing & the sensor just died. I would try & replace the sensor first. If its driving the tranee is ok but sounds like dirt & or the wrong fluid isnt working 2gether or like i said the sensor died. I would replace the fluid with the correct fluid & replace the sensor with a HONDA brand. The cvts dont like cheep sensors.keep in mind depending on how much fluid you put in. The torq converter holds most of your trans fluid. So if changing the fluid your only removing but so much.

Also try removing sensor. Clean it off & re-install. Make sure you push the sensor all the way in if you clean it off. Dirt trapped at the magnet part of the sensor can cause the signal to be blocked thus the computer cant talk to the sensor. Dirty fluid can easily cause this code. Goodluck

Np

Np. You can take a pair of curved needle nose pliars and this should help u pull it back. I either use a curved hook to get up under the hose or i simply pull.

Hi. Your welcome. Make sure the sensor is totally & fully pushed in as far as it can go. Turn the 10mm bolt slightly and reset check eng light to see if it helps. That code normally means there is no signal from the sensor being picked up as it sits in its hole. My true experience has been that once i turn the 10mm retainer nut/bolt a slight hair to drive the sensor down so that the gear in that hole can read the magnet part of the sensor. This usually fixes that code for me

Thank you again. Just want to make sure that I am using the right part here. Is it 28810.RJ2 for this code P0793 ?

Hi. The part# you gave me looks correct. 288810J2-003 and long as u gave the dealer the right info or they gave you the correct sensor it looks to be good. Keep in mind the part number for the input & output trans speed sensor are 2 different numbers. The dealer will want to run some expensive Diagnoses. The problem lies in the gear not being ablt to read that magnetic head of the new sensor. Did u try turning the bolt slightly to push the sensor down?

If it was working right before it failed then thats the problem as the sensor sounds like its not being picked up. FYI. I have had the dealer sell me bad sensors in the past

@@avery214j I will tighten the bolt and see if that fixes it. Thank you!

Hi Long as you put the hose back on like you found b4 u removed them Arrows shouldnt matter. Its what the two hoses re-connect too that matters

Hi I would get a pick set from Harbor frieght. Thats to try and pull outward. If possible get a drill or angle drill and slowly drill it out. Dont go too deep. Watch a video on drilling it out. 1) drill hole 2) force hooked pic into drilled hole and slowly work it out. This will take time. 3) if all else fails. Transmission or auto shops as they will get it out

If part of the sensor fell in the transmission. Transmission shop

@@avery214j I was going to separate the trans from the bell housing and see if I can clean it out.

Ok. If you know how to do that then u have a better chance at trying to clean it out. Make sure you add trans fluid directly back to the t-converter if you take that stuff apart. Goodluck

@@avery214j got it. Thanks.

Hi. That codes means you either have low transmission fluid. (Change) fluid first to see if this fixes issue. Reset light. It also could mean u have a bad valve body inside the transmission or bad wires or the sensor itself may have failed. Just google what does p0962 mean and read

@@avery214j thank you very much. I really appreciate the help

Hi. Iknow they can be tight. Spray pb blast if you have some on your hand and place it on the metal for 15 min

@@avery214j there is no metal. Rubber Pipe is connected to a sensor which is made of plastic

I have to go out and look at the car. Its my wifes but it shouldnt be that hard. I remember it just slides off with a little force

Ok. Im holding purge valve in my hand. Try taking a small FLAT blade screwdriver and stick it between the open while pulling the valve off. Mines slid off with a little force

Also just wiggle back & forth while pulling in upward. There is no lock that holds it on. Worse case you can remove the 10m. bolt that holds the valve mouting plate in place. If you need more room remove the battery as it will allow you better access. The you can pull the purge valve mounting plate towards you to have better access of removing it. The purge valve is made of hard pladtic and its sitting on a metal housing. Idk what else to tell you as it should slide off with a little force

Hi. When u ask if this will work on 05 civic hx. Not sure what a civic hx is. If u have a bad speed sensor all cars will act the same. is the same part# not sure. Things need to know. Year, make, model. Eng size 1.7 or 2.0l. is it a automatic or manual transmission. What code if any do you have? You can go to www.rockauto.com put in your vehicles information and the click on the electrical section. Then Go down to speed sensor and look for output or input depending what sensor you need. Need more details to understand whats going on

Also i have other videos on this car that will help u

Yes all check engine lite codes must be reset and removed from the cars computor . U can try disconnecting the black cable from battery for 20 min. If code returns u must reset w a scanner. This is if u dont have one

Also is it the same code or a different code now that you have replaced the sensor

@@avery214j currently I don’t know. I do not have a OBD tool to reset the code so I will have to ask a friend. When we ran the scanner on it last time it showed that the center was bad. Honda also verified this, but they wanted to charge me $900 to fix it.

Ok. Need to know all codes. But the codes must be removed because thats whats stuck in the cars computor right now until erased

Also autozone or amazon has a cool scanner for like $60. It reads wheel abs codes and tells you exactly which wheel has the issue. Resets those codes too. Reads and resets OBD2 codes too. Its called INNOVA-3040 if u decide to look into it. Very reliable in-expensive scanner

Hi. Ima give you two part numbers but i want you to give them to your autoparts store so they can cross the part numbers. Standard autoparts numbers are S1024 and HP4325 In the future you can just google what your looking for or call any autoparts store I simply went to rockauto.com and put in your vehicles info then clicked on electrical connectors. If your looking for the purge valve electrical connector then those are the part numbers i see. Please verify all part numbers b4 ordering. Goodluck

Np

@@avery214j more videos on the Equinox 2008 would be much appreciated 😃

What specifically are you looking for on the equinox? What do u need to do, replace, fix etc?

@@avery214j like changing the calipers for A new part ,bleeding the brakes so to speak would be fresh 👌

Np. I will see what i can do for you buddy

I have a 08 honda accord v6 and the d light blinks with no check engine light on and my rpm go high then it catch gear. But when I cut my car off the d light stop blinking .. someone said to add transmission fluid or it could be my transmission pressure sensor is that true ????

@@avery214j doesn't reverse means when u put it in the reverse gear nothing happens, i.e car doesn't reverse, so i have to shut the car down and again start it so the D blinking goes away to reverse

Yes!!!!

Ok. Yes a broken wire down there would be a problem

Thanks. Im useto it now. I try my best to give as much information as possible

Hi Look with a flashlight and you will have the answer. I would think so but dont know anyone who drives a manual trans.

Just curious. Did u look and is it in the same spot?

@@avery214j Yes, its there. The blue one is not next to it though.

Ok

Yea and the connector to the sensor is angled differently rather than straight forward

Hi and the answer is no. Lack of oil or antifreez will cause your eng to overheat. That sensor is related to your transmission only. You could also have a stuck open thermostat or a jammed closed thermostat which can also cause your eng to overheat.

Also how is the car driving? Shifting?

Np. Take care

Do you have a check eng code. Meaning is the light on? Vehicles can stall for a number of reason. These are just examples. Low fuel pressure, failing alternator as it controls everything in vehicle once the engine turns over. Vacuum leak. Hose not connected. Failing camshaft sensor. A lack of fuel flowing. A lack of the correct amount of air. Ignition issues.

As i read what u said again about slowing down and then vehicle wants to stall. Reminds me of a possible vacuum leak

​@@avery214jIm not the same person as him but i have an 05 tb too and it has the same problems. ive tried to find a vacuum leak and cant. taken off the entire intake and everything. Drives still but sitting at idle once at operating temp it wants to die. ive replaces most sensors. tightened up the exhaust to make sure no leaks. im lost and the only think i can think of is a bad fuel pump

Is there a check eng lite showing any codes. This sounds like a possible vacuum leak if no codes are present

Could also be a clogged fuel filter, low fuel pressure or the timing is now off out of sink for whatever reason.

Im proud of you!!🦾🦾🦾

@@avery214j Thanks !

Np brother. Thats all im trying to do is help mankind save$$$$ and help themselves

It's the same bulb

I would see a local mechanic as their are a number of reasons for this that should be evaluated by an onsite mechanic who can physically look at the vehicle

Make sure u have no lose vacuum hoses or holes. Make sure you dont have a valve cover leak. Chk pcv valve for leakes. Start car and let idle. Then disconnect ignition coil for the cylinder still having misfire. If the car run better with that 1 ignition coils connector removed then the coil itself if the issue

Only disconnect the coils electrical connector while car is idle and listen to see if it runs better

@@avery214j ac is off it drives better than before the engine light erased went off after charging the ignition coil but it’s has mild vibration so my concern is I changed my spar plugs three months ago and I checked on them the condition is pretty good i gapped them back so meanwhile i checked inside I was thinking any oil leaking but there was no leakage of oil.

Ok. That makes sense. Regardless of the vehicle when u use the AC u put an extra load on the engine. Thats sorta normal

Lol

Just like in the video

Np. Glad it helped

Np

Your welcome

Welcome

Welcome

👍

Np. Your not crazee. Theyre for making a product w no instructions

Only the one that set off the chk eng lite. Each 1 will set off a different code

Thank you and Jesus loves you

Thanks!!

How many sensor are there, 4 or 2?