I have the exact same issue with my 2017 Nissan rogue where do I get to the panel on the 2017 Nissan Rd.?

Hows the drone on that thing, if you still have it

Any tips on taking thd bulk head wiring off?

EXTREMELY helpful. Thank you Sir!

Gracias si suluciones mi problema gracias

Nice to say hello, could I change the CV joint and would that also fix the problem?

Great job my friend. Thank you so much great help God bless.

Thank you! Just did this in no time at all. Wonderful video.

Torque converter bolts are 17mm and you have to turn the engine by hand to get to them, the crankshaft bolt is a 22mm

Pariente A cuánto van torqueados las bielas ?

How do you extract the fuse nearest that big fat white "extender plug?" ( it blocks access) and what is the name of the extractor pliers? you used on this video? thxs

Bro do you think i can put an SI cluster on my 8th gen hybrid IMA civic ? Because I’m tired of the blue color i want to switch to red

There are after market one that are all one peice and cheaper than a grand

Thanks man. Very helpful

I have a 2012 5.7 2wd thank you so much I guess now the only part that scares me is buying the overpriced driveshaft

Thanks for the vid bro. Luckily my wife’s rogue had an extra fuse.

Great video, straight to the point and informative! Problem fixed !

Did you use a ball hone on the cylinders? Or just slap the new rings in?

I’m in the middle of this: he’s making it look way quicker than it really is. You’ve got to remove the thermostat housing pipe thing, detach the exhaust, get harnesses out of the way. Figure 5 hours to get both heads off. And tons of gaskets and o rings and shit need to be replaced when putting it back together.

Thanks, Sir

Lo que quiero ver es como lo pones para tras??

Do you know the location of the fuse for the boot 12v socket? I have the same issue but reversed, cab sockets work fine boot one does work

How long did it take you to do?

Exactly what I needed. Thanks so much!

I am changing piston and rings, my first time doing the job, can you maybe guide me with what is the correct torque on the pistons please

Thaks brother for this video, you helpme so much

Thank you for your video, I’m going to try to do fix this issue on my Nissan tomorrow :)

For mine it's the front drive shaft comes out and it vibrant slot before coming out

that's a tough job to do on your back

Thanks for the video. Can you point out where the cargo fuse is located?

Im doing this job right here not the same year but same procedure . Been at it for 2 days tomorrow she’s coming out

This did not help me remove my engine

I don't agree in buying a new one i took mine down and put grease in the bearings thats the clicking noise it took me about 4 hours and it runs perfect only 10 dollars in grease

Did you notice the harness’s for fog lights already on vehicle ? Can those harness be used?

Well what you do, is replace the tensioner then check timing and codes, but since you jumped straight to the chain swap, I hope this isnt something you sold to a customer, or you scammed them

Having trouble getting the 06 Honda accord engine in from stop what should I do move back mont

Did you replace the front drive shaft along with the rear that you showed in the box??

Question I have 2013 accord coupe V6 2nd engine 28k and fuel in oil also getting around 14 mpg before install did timing belt water pump spark plugs and they were supposed to do compression test , leak test and lube everything etc .. Had same dealer do oil change after install and I complained about mpg they said everything was ok , need another oil change dealer was to busy took car to different mechanic and he found fuel in oil took back to dealer and they replaced injectors and guess what same issue , Bringing car back this week my guess is piston rings are bad so should I expect ring job or should I start looking at another new/used engine? Unfortunately extended warranty is now over ( only had 4 months left after they did original replacement. Any thoughts? Any ideas?

Very good brother

El maniful de escape Y de intec qué se quitaron solitos te faltan muchos episodios porque como que te sudó el pedorro bastante para avanzar

I got as far as the second round of that horse shit horrible ghetto terrible audio fidelity and bad audio production bass stupid “ music”…. And bailed… That isn’t music… it’s crap reproducing the sounds produced in a 1979 impala with a $19 subwoofer powered by a $29 graco 9 million watt trash power amp

Very good! Recognized the drive shaft bolt braces right at the beginning. Good way to re purpose those! Good job sir very nice.

Man tell me you live in Dallas TX

wow!!! Hats off bro!!!

U guys find the part?

Ok but what else can we look for ???

Hell yeah get it guys love the trap music and BMW is I thought I was the only one keep it. As well I'll run a professional business these days self-taught and you guys know that what you're doing

muy buen video y muy bien esplicado en los dos idiomas a mi me ayudó mucho gracias por acerlo así eres buen muchacho y sigue así saludos Chavalon Dios te bendiga siempre

Great Video. Any experience with fuel gauge not going below 4-5 bars and no low fuel light when empty. Replaced sending unit & upper instrument cluster - dealer says main instrument cluster (Gauge Control Module). No other issues with lights or gauges.

Exelente