How hard is it to program

❤❤❤❤❤❤❤

What’s was the code number?

If you remove the wheel wells ,cyl 6 seems like an easier access ,but i never tried it that way

How did you get to that point tho? I’m dealing with this issue and it has me checking continuity between the clock spring and the srs connector #2 and some other bullshit. I have no experience with this shit and my manager just threw this at me and I’m trying to not look stupid. Did you just changed the module and hoped that was the issue?

What does it mean when it surges while doing so

That mess didn't happen in a day. That is the worst I've ever seen that's straight up neglect.

I over filled the DEF and after driving start leaking from the top keep in mind it is a new unit installed about a month ago but this my first trip (the unit looks like its not installed properly) any info will be helpful thank you in advance

Do you have to drain the radiator ?

Did you reuse the same lines?

This guy didn't show how to take it off

Hey sir , your changing Foot brake valve because the brake lights aren’t working?

Is that oil? Or why does it look like that?

Seals have a side indicator marked on them, not sure if that make any difference but i would follow just incase it is.

When they has a corrisen has to replaces

Thank you. Got a leak from egr😢

Hello, I have a M4 that brakes not well and comes with a manual gearbox

How did u clean it off

Problem is we done Regen, scr test and codes are still there. We are running a second scr one now. This is a nightmare.

Detroit did finally fix the overhead issue by introducing oil drilled rockers. However, I've noticed a few other common issues with these engines too. Wrist pin failures, usually caused by the valve bridge falling off, camshaft failures again caused by valve bridge failures. The upper liner o-rings will leak coolant and blow a headgasket. Headgasket oil leaks are still common, dd13 Gen 5s had a random issue of not being built right from the factory and the oil control ring was put on the wrong section of the piston. The injection pumps have started to make holes in the housings. And I've seen several with oil starvation requiring an engine or crankshaft replacement. I do like working on these engines, except for the fuel system I have not had good luck with the new high pressure fuel lines. I do not believe that these are good engines because of just how many problems I have seen out of them, but the newer Gen 5s, late 22 to present are definitely better than the early ones.

That's what my truck says along with starter block shift to neutral

Dd15 Engine.# I did stripped one of the bolts from the gasket,when i felt it did stripped al little , i stop to put more torque,do you think it will leak bad?

How to reprogram after replace it ,is it easy?and if i just take it out to clean and install back ,do i need use program to reset.Thanks

I never though they had airbags on the cascadia

This helps

Is there a link for the replacement header? I need to replace mine and have no idea how to make sure I’m getting the correct part

Is there any workaround to get it out of limp mode derate? Trying to get it to our yard to fix the issue there

The camshaft cap order matter righ?

My heater control valve on top of the def tank is getting very hot. I have already replaced the header. Will the heater pump cause over temp for the level sensor?

Programming not necessary, also no need to disconnect batteries, just flip cutoff switch

🌼🎉🎊👌✌️💪👍🌟👏❤️🔥🏵️💫💥✨🏅OKIiiiiiiiii

✨💥💫💪👍🌟🌹👏❤️🏆🏅✌️🙏🌷👌🌼🎉🎊 very very very nice

Thanks for the video. First thing I checked that was it.

Why did u replace it

What software do you need for programming

Is the def sending unit in the same circuit as the deft tank tempature sensor? I have a check engine light saying it can’t read the temp inside the def tank

I need a cam frame for a dd13. The dealer cant get them. On back order. All the ones at the juck yard are already trashed

👍👍👍👍👍

Should I buy gen 4 or 5?

Thanks will try

What is the reason you charge it?

When You mentioned programming, what has to be programmed after install? I'm replacing my SAM CHASSIS and not sure what you actually have to program

I have a 2022 gen 5. Recently I’ve had an issue with the unloader valve sticking. What I was told there is no permanent fix yet. It’s under warranty But!!!! Replacing the air dyer or air compressor will not fix it! Are you aware of this issue with these motors? Apparently Detroit and Freightliner are aware. Thanks in advance

Really appreciate the time and efforts for these videos you upload. As a mechanic I’m learning a lot and can’t thank you enough for posting these kind of videos.

Shop policy where I work is we have to stay in the truck while it’s running a regen so it’s movie time when I see these codes lol

What's the total cost for replacing the SAM chassis???