Hello, I am new to 3D printing and I wanted to know if with only the 2023-car-model.stp model it is only necessary because I want to send it to be printed by a company online, thank you very much in advance

If you want to all give you my number and we can try to meet up at scout camp

I didn't know it was this flooded now I'm in the last session and it's sad every year see it flood more and more 😢. Thanks for publishing awesome content like this.

Just bought the tracker and the capsule. I am thinking that adding a JST connector right at the battery would be useful, allowing the battery to be disconnected without opening the tracker part of the capsule. Admittedly, with the new switch slot, this might be redundant. I will also probably put a piece of tape over the switch slot during flight to keep ejection gasses out of the capsule.

You've done an amazing job with all the updates. So cool to see the OpenRC F1 project live on. Well done

can you show how you connect the rrc3 with pc? i used the comm pins for connect rrc3 to pc with usb-ttl. I can't see the rrc3 connection on mDACS. So, i can't programm it.

Is it recommended to just use a flux infused solder or could you use a tube of flux to help handle the heat and have better flow when soldering the more sensitive pads, like the RF module and the radio?

I remember loading my own single shot round film discs into a Camroc. For 10 year olds in 1970 this was super high tech!!

Just my opinion here... The camera rocks, the mount is janky and simply doest hold up to midpower thrust. You can permenently mount it with stronger tape but still pretty dubious. Pros with mid power is your rocket doesn’t spin with it installed. Flying it on Estes Star Orbiter. 😊

What infill pattern did you use?

Great work! Looking to build something like this for our new club. I’d like to see a follow up video of this in use with things you’d change, things you love, etc.

Hey, that’s my nose cone! It came out fantastic, I couldn’t be happier….. that’s why I ordered 3 more from you LOL

lol I have the same computer case but with red leds but now when I see blue leds it looks better

Not bad. You will learn tho, that the devil is in the details. Measurements matter, detail matters, especially if you want a good looking rocket. Yes, I definitely want to see you build this out. I hope it turns out great and that you fly it often. I want to get my lvl 1 and 2 certification this year and am about to start the builds for both. Yes. It is my plan to have a bigger rocket for each lvl.

Mr. Beast???

Did you happen to ask for the rpsma connector? From eggtimer?

Because of the recent Lego dnd set, Ive thought about a lego inspired 3d printed d20. Dont know if it’s possible, but honestly think it would be cool

Great video! I agree about the cellulose fiber. I use it regardless of my other protection being used. Cheap and lightweight insurance!!! I had never seen the deployment bag before. Thanks for showing that one. I’ve been testing an electronic chute release unit called the ACE that currently fits in BT-60 rockets, but hopefully will offer different sizes as well. It releases the chute mechanically as opposed to a combustion charge saving it from potential burns. Great tutorial and thanks for producing this video!

how do you have such passion for cars and still say 'tires' when talking about wheels?

What camera is this? Do you have a link?

This is my first time trying to print an Open RC Car, so with the files you listed the 2023 ones seem just cosmetic correct to the car shown in the video. The Other Files listed (2017) are the ones needed to operate the actual car correct? (Without electronics motor etc..) Which parts would I print out? Should I print all of the Original Noree Parts then go to the IPL 2023 Parts list and go from there? Any information would be helpful!

Is there a recommended position on the rocket where you mount the camera? Above or below the center of gravity?

Do you sell .stl files for this build?

most RC will just spin around, show me 1 of those putting down F1 SPEEDS!

great video :) i am lvl 2 as well. For my L3, its gonna be stupid simple, a basic cardboard airframe with lots of drag. No need for it to go super high. If it hits a mile, im happy. Im willing to bet we could get a 3 inch cardboard airframe, lvl 3 rocket, to hit 20,000 feet no issue. actually, let me think about this... Maybe the cardboard wont work for an L3. the inside paper that holds the motor mount, might tear, even with good epoxy. Unless i put some wood screws into it from the side.... But then that might weaken it by introducing a hole and then could zipper the rocket... oh man. now im up for the challenge to do a L3 with a cardboard tube.

I like this shorter informational videos bro, def consider making more like these about other rocketry concepts!!

I recently had a late ejection and the rocket was in "nose over" configuration. The chute deployed "forward" and opened, but trailing body tube drove right into it causing it to collapse and let to the demise of my rocket. I prefer "At Apogee", as it helps separate the parts and no on-coming wind to drive the parts back towards one another. Great video and it gets the mind juices flowing!

I like how the closed captioning calls it a disaster cam.

Surprised you would recommend a scratch build fiberglass rocket for lvl 1 cert. I could see maybe for your level 2, but I'd point people to a 3 or 4" kit rocket. 🚀🌳

Can you do ground testing with the MDACS software?

Duct tape will hold that puppy. 🤠🏴󠁧󠁢󠁳󠁣󠁴󠁿👍🇺🇸

Great content. I was having a very difficult time with the beeper programming. Turns out a friend had the dongle that I could use. Thanks for such an informative and helpful video. You made my NASA Student launch payload deployer work.

Why did you go with two LCD receivers? Two different rockets on two different channels?

Way to big

that’s sick

being that ii race rc cars this is cool but the only real issue i see with this is cooling the electronics

Nice!

I just printed this rocket and I noticed it will fit a 38mm motor. Oh man this is gonna be fun

Great job building! Definitely helps to have an extra pair of hands to speed up the build process too

Just now saw this video...why not take an Estes or other camera's 'guts' and put it in a tube that just 'plugs into' a standard rocket tube (BT-60, etc) with access to the SD card when you take this small tube out....but for now why not print your existing covers in orange and not grey.

Thank you for all the detailed work. I plan on using this video to help me assy my first egg timer q. I will let you how it goes.

I'm still at the model rocket sizing. But have looked into high power and these look like an awesome alternative for ebays.

Hi nice job can you make a redesing and more acurate rear wing?

I was wondering if the small lip made on the side that is direct to the build plate affecting the roll at all. I saw some people print them on removable platforms that may make a more accurate dice but I'm not sure.

Is there a particular reason you go with the tracker in the nosecone vs the e-bay?

Need to to do a center of weight test in water

hello !! were did you bought your eggtimer?

Why did you use alum tape under the layup? And I would recommend cutting the glass at a bias instead of at 90 degrees.

The only thing bothering me is the lack of grip. Can you make rims that can fit the common RC Foam compound for maximum grip? :)

Switch access would have been great.