OK, the fear of wheel wobble and dying means I'm not removing this front wheel. I want to know how to do this without removing the front wheel.
@RideWNC6 сағат бұрын
Wheel Wobble? That is from dumbazzes running worn out tires at high speeds. Not from removing a front wheel.
@argentosebastian2 күн бұрын
@0:51 There are 2 spacers. Right and left side. The short one is on the brake side? Thanks
@montecarloss1964 күн бұрын
I just want to add my comment. Good video. When putting the front drive shaft back to the rear. It is a certain way it has to go back together as he said. If you look at the base of the tail you’ll see the spline orientation. Hope that lil bit of information helps someone. I figured that out struggling with mine for about an hour.
@mjsperber41125 күн бұрын
What bike are you riding Mike?
@RideWNC5 күн бұрын
2009 Ducati M1100
@alanabee9138 күн бұрын
Whats the name of the German restaurant please and thank you.
@RideWNC8 күн бұрын
hofbrauhaushelenga.net
@ronborras6378 күн бұрын
You just drove by my property (minute 2:27), Martins Creek @ New Martins Creek, stunning road, I call it a Minnie Me Tail of the Dragon, curves and switchbacks all over, cold as fuck in winter, rain, fog, etc. keep eyes open, heavy wildlife population crossing the road, be safe out there.
@ronmastel8588 күн бұрын
Any body else notice that the guy pulling the wheel is not the same guy who's channel this is? Why do you keep referring to yourself doing the work when clearly it's not? Anyway, very informative video no matter who actually did the work.
@RideWNC8 күн бұрын
That seems racist. Sometimes my Vitiligo is lighter than usual. Trump2024
@amari17099 күн бұрын
Does have 2 or 1 coolant
@angrypeach13989 күн бұрын
IMPORTANT NOTE ON BOTTOM BEARING: PUT THE SEAL IN BEFORE YOU PRESS THAT BEARING IN OTHERWISE YOULL HAVE TO BREAK THE BEARING AND BUY A NEW SET. THE SEAL IS VERY IMPORTANT...I FORGOT THE SEAL BEFORE THE BEARING AND HAD TO BUY AND DO IT AGAIN...😅
@RideWNC9 күн бұрын
OOF!
@angrypeach13987 күн бұрын
Hey buddy do you press the bearing to the triple tree down down or do you leave a little gap between the triple tree and the seal with the bearing? Cause i saw that if you do press it flat all the way down its difficult for the bearing to turn? Please advise
@RideWNC7 күн бұрын
@@angrypeach1398 That info is not correct. Stiffness in turning is caused by too much torque on the nut. If you leave a gap that gap will turn into slop in the steering after the first wheelie.
@HORRUS299 күн бұрын
When I pressurize the line then Crack the bleeder valve I get a ton of air bubbles. I've run almost a entire bottle of brake fluid through the line, but I'm still getting the bubbles.
@RideWNC9 күн бұрын
The air is coming from the threads of the bleeder valve, not from the brake system.
@HORRUS299 күн бұрын
Ok, that makes me feel better. Thank you!
@r.williamcomm76939 күн бұрын
Hey just wanted to thank you for your video because it really helped.
@opes13410 күн бұрын
This is a life saver. Thank you so much for this.
@user-vj1mp7nf6e10 күн бұрын
Друг, подскажи, какой момент затяжки болтов траверс. Нигде не могу найти.
@RideWNC10 күн бұрын
Honda Africa Twin Rear 74 foot pounds 22mm and 27mm 42 psi Front 44 foot pounds Axle Nut 15 Ft/LBF Pinch bolts 23 ft/LBF Calipers 45Nm 38 psi
@jamesmelendez454911 күн бұрын
Thank you, sir! I'm from Simpsonville, SC, and a friend, and I will definitely be trying that road. Make a day trip out of it.
@cookielover1018TM11 күн бұрын
Two weeks ago we rode Cleveland Tn to Ducktown to Tellico Plains to Robbinsvilles to Ducktown, a twisty and beautiful ride, enjoy your rides and appreciate the video
@totacarbajal11 күн бұрын
Tenía juego el yugo o porque se le cambiaron baleros?
@charlireone11 күн бұрын
Thanks you made it easy
@RideWNC11 күн бұрын
1:56 25MPH Fox
@DogsOnAcid12 күн бұрын
What size torx bit for a 5mm Allen?
@RideWNC11 күн бұрын
If you are asking that question, you probably need to buy a Torx kit.
@DogsOnAcid11 күн бұрын
@@RideWNC I have some torx socket drives I'm just wondering how oversized do you go? I.E. just over so it does't fit or next size up?
@svdcleveland12 күн бұрын
Does it matter that my axle bolt goes the opposite direction? The nut is on the left side instead of the right. Is it worth removing the wheel to put it through the other way?
@RideWNC12 күн бұрын
Nope. IT will be OK.
@svdcleveland12 күн бұрын
@@RideWNC Thank you. If I ever do have to remove the rear wheel I will be using this video. Thanks for posting.
@danosono12 күн бұрын
nice ride
@shaneson125812 күн бұрын
Guys look closely to where the hard luggage pivots on at. THIS bike still has the fable unicorn of rubber grommets on there still...
@RideWNC12 күн бұрын
Typically the bikes which don't have the rubber are not DLX.
@cookielover1018TM13 күн бұрын
I did the Telico Plains to Robbinsville back to,Ducktown, lots of twist and beautiful elevation . Did this 10 days ago, thanks for video
@jprunka113 күн бұрын
Is that a radar detector? I've been trying to figure out how to mount my Uniden R8 on my Street Glide.
You have to contact the company and get on the waiting list. When they are in stock, they sell very fast. adaptivtech.com/pages/contact-us
@zagdankrzysztof716213 күн бұрын
I go to TM, thanks for advice Pal
@rec101514 күн бұрын
Its a 2012 Pathfinder Nissan
@rec101514 күн бұрын
Hello l, canyouhelp with with a issue I got with my car?
@jpisme908216 күн бұрын
I ride that area yearly and going back up in a few weeks. I'm going to see can I locate Old 64. Looks like my kind of ride. Past year I stay away from the crazy Dragon Tail and such. Back roads are the best.
@1994RALLY16 күн бұрын
My mpg is really bad and it’s throwing that code
@jasonisdn16 күн бұрын
Thank you for sharing that area. I am looking at it on Google Maps now lol. I am not that far away from there. Have you rode in the area known as Devil's Whip? Buck Creek Rd ?
@RideWNC16 күн бұрын
I never ride more than 100 miles from Murphy, NC... I have no need. All of the good roads are within 100 miles and I can sleep in my own bed and do it again in the morning.
@HenryIndula17 күн бұрын
En français ce mieux
@RideWNC18 күн бұрын
3:00 Hit by a bird.
@cookielover1018TM18 күн бұрын
Last week I rode Chattanooga to Ducktown to Tellico Plains to Robbinsville to Ducktown, awesome ride, enjoyed your ride sir
@RideWNC19 күн бұрын
I am so sorry if that stupid Kamala commercial pops up. Please know, none of us on KZfaq want to see that hag!
@beastbomber251119 күн бұрын
I did this exact thing but now my front wheel Is super tight any ideas?
@RideWNC19 күн бұрын
Speedometer is not lined up correctly.
@RadRacer137819 күн бұрын
Great tutorial, thank you!
@AntonioVasar119 күн бұрын
Thank you for the video, unfortunately I found it later after I removed my cracked stator cover. I will look for the tool
@RideWNC19 күн бұрын
That totally SUCKS!!!
@2wheels-tattoos19 күн бұрын
Looks like I'll be trying new tires with the increasing prices 😢
@abysswalker240320 күн бұрын
I wish all bikes had single sided swing arms lol, so much easier, don't even need to touch the chains tension or worry about aligning the wheel
@30NLF21 күн бұрын
Thanks
@myredute21 күн бұрын
Completely useless video when you don't actually show the position of the timing marks by doing a close up on the pulleys. Absolute rubbish!!!!!
@lonewolf36s22 күн бұрын
Which side does the big spacer go on? (joking of course haha @8:56). Thanks for this video, this is something I generally had a shop do, but these days doing everything myself that I can. And I'm very soon to be due for new tires on my 848. That lift is awesome by the way. I want one of those.
@countryboytracks31924 күн бұрын
Why put the axle in through opposite side all my r1 & r6 axle goes in through left side axle nut and washer on right side
@RideWNC24 күн бұрын
Nope. I put a bike together the way it came a part. Not my bike. Not my place to question the owner.If you notice any bike I work on, the parts are on the sides they came off of.
@chrisfurby824125 күн бұрын
This vid in addition to the owner's manual make this job a breeze, thank you 👍👍👍
@x1aou28 күн бұрын
Well, thankyou for this video. I learnt a lot and it took way longer than it should have. Learned some stuff, made a couple of mistakes. Great template, thankyou 🙏🏽👍🏾
@gerardolopez4422Ай бұрын
Excellent video thank you
@2wheels-tattoosАй бұрын
We could barely keep up with you❤
@2wheels-tattoosАй бұрын
You didn't ask if we wanted to join you!!
@RideWNCАй бұрын
You guys are Dragon Slayers. You would not have fun riding other roads.
@VictorDC61Ай бұрын
What do you mean by "oil issues"?
@user-ew1cg7wg7uАй бұрын
What is the torque specs on the oil pan for the transmission?