what do you recommend for i beam welding? stick or the one that u used? for structure

The only thing that I learn was that anyone can pickup a disk and turn it one way or the other in a video without educating us as to, should the label face up or down. I guess people will do anything to get a view on KZfaq. Maybe I should post a video asking “should I use my left hand or right hand to open a jam jar” and see how many hits I get.

Best tricks with out peper shabash

how to choose the type of welding ??? or TIG is the most widely used one ???

I don't think that is short circuit MIG, Spray Arc or globular. And yes! Clean surfaces for best results! MAG drills rock!

Any tips for 45° joint?

Bein ❤

Method 2 worked a treat for me. Easy to cut it out. Easy to weld it up and turned out nice and square. No more 45 degree mitre cuts for me!

❤❤

Like the 300,400= 500 trick ;-)

Them block outs looks rough with no radius

Now I’m legally blind..

Great job! Ur doing ur job properly, unlike my workplace who are also a structural steel fabrication company however they tack their plates on unclean and on rusty beams with mill scale too. This is the proper way to do it. Grind the weld area of any rust and mill scale for a stronger weld and reducing the risk of porosity or other weld defects which may lead to re-work. But once again, my workplace dont care and if they get porosity they just weld over it and theyre like "ohhh itll do"

So i take it the key is to cutting the plate on an angle so as to reduce the surface contact with the blade to the material...ergo saves the blade from being force through more metal less heat and blade warping amd risking teeth snap off....never thaught of it till the day i tried cutting a 3/8 plate with a 12" cutting wheel normally meant for cutting bolts and then i realised that standing the plate up in the vice you could get better results...so i suppose the principle is the same...may be a newb observation but eh...you gotta try and learn new ways eh

This is exactly how you are supposed to weld mig. No more stacking dimes because that’s actually a cold lap poor weld when you stack dimes. Nice work you could have welded for me ! I’d turn you loose and walk away and come back on payday to pat ya on the back!

Yes

May God’s peace and mercy be upon you, and thank you for the video that presents the content. I want to thank you for this content. For a simple request and I need help. I have been working as a welder for more than 20 years and I have evidence of experience and I have worked with major companies. I am from Morocco and I am looking for a work contract and immigration. Can you help me? Thank you. I needed welding, I am a good welder, you will not regret helping me

❤

.lm alktroda

.hawer weyo

Baliram fabricator

Been working on my pipe welding/ fit ups. This helps a ton for saddles. Thanks

Nice job, need to clean the steal before welding :)

Where do you buy the replacement railing pieces? They look very authentic

Wire diam?

#3❤

Why is this so cool . I know nothing about this and just can't stop watching

Drilling with gloves on 🥶

The best tricks aren't on youtube

How many ampers did u use? Around 65?

Studied up to 7th Class in School in 1996 Later did SSC through correspondence in 2018 Fabrication Works 12 years experience I want to good job sir I am Indian

What's the tolerance on that because that isn't flush at the flanges.

lo, like this is new. i learned this from an old timer 40 years ago, but i used an abrasive cut off saw. i also built many aircraft fuselages thin wall moly used a tin snip.

What kind of abrasive is that? That took that weld off really fast.

To cut that far back, then cutting the points off, you’re wasting time and materials. Too many steps. 1/3rd of the pipe diameter is all you need to cut back. Then grind insides. That’s it. Done. Don’t complicate things

U first make a cut for 12 before the 32? ..

A lot of marking out for something you can just eye up. All U needed was the top centerline and a bubble on the top flange to the side of the plate

WhatsApp number sir

How many amps did you set?

Why You don`t clean metal before fitting and welding ?

Dope mark techniques

Are you mute ?

Prep is key and you didnt prep any of your steel. Thats why the welds are a bit ropey.

Use the strap on your jei mini beast - it's not nice if the magnet looses grip trust me it near cost me my machine as it helicopter'd around until it cut the power cable 😬

Hi, Thanks for your videos. It is very instructional. Can you make a video or just explain how to increase a loading of a H-beam. Some people weld plates to the web. Some do Boxing the flanges. Can you show how it is done. I did not find any video on the subject. Thanks

STOP STOP TERRIBLE VIDEO NOT INFORMATIVE AT ALL

What kind of psychopath writes down 1300 mm instead of standard

Bonjour jai une petite question s’il vous plaît, je dois posé une poutre HBE de 200 sur 7m de longueur qui vas supporter plus de 20t …. Quel soudure je dois fair pour être plus rassuré….. merci

You made a rookie mistake by not locating the flange holes off of the centerline of the web. This fails to correct for mill tolerance and can make a misfit when bolting together the beam.

Hole size Tel me bro