Пікірлер
@josuerodriguez3188 26 күн бұрын
Thank for the video!, just did mine did not have to do half the steps, just removed the Car rubber water Seal, then unclip some of the sides, then go straight to the plastic liner, unclip and disconnect light, then remove, mount the module, I was able to use a drill , place it horizontally, and tighten, before connecting to module make sure you disconnect negative terminal on battery, then connect. Good luck, easy project.
@eronshaw3084 5 ай бұрын
This is an excessive amount of work. The entire bottom of the vehicle doesn't need to be removed. The rear side panels can be popped loose enough to remove the top headliner panel. It's still an informative video. Thanks for taking the time to show people.
@jamestao539 6 ай бұрын
Great video, couple of questions: did you bought the fobs from the dealer or someone else(and how much did it cost); and does 2019 RDX the same as 2021 RDX? Thanks 🙏
@lsmith3907 6 ай бұрын
Holy moly thats rediculous for a remote start. If the app can do it, it should be an easy fob program...
@benvillegas86 8 ай бұрын
Could you please share the remote starter kit link, I’ve been trying to find it and I just haven’t, thanks in advance
@han027 10 ай бұрын
Could you share where you got the kit?
@user-ez2tt2ih1p Жыл бұрын
so i have a 2021 rdx aspec that ,when i had the free subscription, could remote start the vehicle. does that means i just need to get some key fobs and have them programmed?
@anthonycisternas7721 Жыл бұрын
Is this the same install directions for a 2022 MDX?
@bullcity5057 Жыл бұрын
What was the part number you used?
@bullcity5057 Жыл бұрын
Can you do a video for the 2022 MDX please
@TheRafguitarist Жыл бұрын
Do you have to program the new key?
@TheMstwntdLMSV123 Жыл бұрын
The dealership recently did mine. There’s a horrible rattling noise coming from under my dashboard since they did it, but it doesn’t look like you did anything in that area. Do you have any ideas? They left grease all over the place on the interior so I’m hesitant to take it back if it’s a relatively easy fix
@visualizediy3920 Жыл бұрын
For my RDX, it was 2019. Not sure if Acura removed the wire harness inside the rear trim; this was for the remote start module. If your model is newer than 2021, you may have to check with the dealership if they needed to install a wire harness. If so, I assume they needed to open up some panels in the front dash...I hope not!
@ITRLOVER 2 жыл бұрын
Got it done quick thanks to you!!
@romecalderon8179 2 жыл бұрын
yup i followed this guy instruction took me 3 hours he did it in details also the key programming cost me $200
@agracer1000 Жыл бұрын
Which PN did you buy. The parts he linked only shows the remote receiver and the two keys are $200 each.
@Apdc5k24 2 жыл бұрын
I followed the updated instructions and it took me an hour to install. Although this video helped out to get through the new steps.
@johnnytvisto5112 2 жыл бұрын
Hi I know you worked thru to get to the wires, but I was really looking forward after you installed the bracket to see the receiver connected to the wire... And it sucks that the dealer still have to charge $140 plus tax to reprogram the new keys, question is the reprograming of the keys for the car to star when the brake pedal is pressed and the push button ia pushed? I assume the receiver and the new keys are already communicating to each other... Good video anyway you shed a lot light ...
@Laissez_Faire 2 жыл бұрын
😂 the first 15 mins I thought you were pulling my leg. Man!! You nearly took the whole car apart just to get the remote start on this Acura. Something that’s standard on all lincolns. I just got an Mdx but I don’t think it will be long before I trade it for a navigator. It’s sucks that it doesn’t have a auto start or 360 cameras
@Apdc5k24 2 жыл бұрын
Can you do another video of the new technique with explanation for each step?
@Douglaskyle9191 2 жыл бұрын
How did the wiring work? Is it just a pre existing wiring harness that you in cap and connect to the box? Does it require cutting and splicing wires ?
@pastorluisdelacruz6757 2 жыл бұрын
I can't believe how much work you have to do to install a remote control on the RDX it is not worth it. they can make it easier they just don't want to do it. is is crazy just to watch
@visualizediy3920 2 жыл бұрын
once you get passed few under panels, all is good :). The remote options is pretty cool though; no need to depend on the App.
@YTgrinderr 2 жыл бұрын
Hey, thanks for the video; I have 019 A-Spec; I was wondering if I can start the car only with the app and avoid this installation
@in2zion478 2 жыл бұрын
yap, you can use the app only. NO need to install this. If you want to start the car via the key, you will need to do this.
@YTgrinderr 2 жыл бұрын
@@in2zion478 I had the app for a year; I couldn't do that; how can the car be connected to the internet? Does that feature work for 2019 RDX?
@visualizediy3920 2 жыл бұрын
well... I think Acura placed a transceiver that receives satellite signals for the remote start. Nevertheless, my car was 2019. It will work. Remember, even after the install, Acura dealership needs to program it.
@YTgrinderr 2 жыл бұрын
@@visualizediy3920 I’ve contacted AcuraLink and subscribed for the yearly small plan, $110 per year. I thought it was better to pay $110 than open all parts of the car. I won't keep the car for more than three years. I usually change my car maximum every five years. Anyway, thanks for all the replies
@happy_days3820 2 жыл бұрын
Nice job
@2418turo 2 жыл бұрын
Is there still no other way of doing this quicker other than removing the whole back end?
@in2zion478 2 жыл бұрын
Hey Arturo, Nope there is no other way. If you decide to stick with the app, it may be a better choice. In the instructions, they want us to fully remove the side panels. I managed not to do that...it saved time. Just make sure you tape up the panels before trying to remove it. This will prevent any scratches on the plastic panels. Good luck!
@kikomanster8188 2 жыл бұрын
I was ready to do this thinking it will be an easy one after seeing what’s inside the box until I saw the whole process of removing everything. I will just use the app and subscribe while I keep this rdx. That is way too much work, even the part where you attach the transreceiver. I am afraid of hearing rattles in the back after doing this and leaks after removing the sealing liners. I commend you for doing this video for those who have the courage to do what you did.
@2418turo 2 жыл бұрын
@@kikomanster8188 it is actually. I found a really easy way how to do it
@2418turo 2 жыл бұрын
@@kikomanster8188 I’m going to post a video in a bit on how to get to it within 10 minutes and do the whole install in about 30 minutes
@anthonycisternas7721 Жыл бұрын
@@2418turo do you have that video yet?
@regmatt 3 жыл бұрын
Nice job !!! if u had to dealership for them to get installed how much would it cost ??
@visualizediy3920 2 жыл бұрын
If the dealership does it...it may cost about $500 to $600
@reynaldosanchez3547 3 жыл бұрын
Did not see any instalation
@Chineization 3 жыл бұрын
You should know that your RDX could be starting with your phone. Just download Acura app from the App Store!
@hav2enjoyit 3 жыл бұрын
yeah, but it has a cost.it’s not free. it’s a $260 premium price.
@YTgrinderr 2 жыл бұрын
I had the app, but I couldn't start the car; I guess because there is no receiver,
@seantowingandrecoverytowin2504 3 жыл бұрын
U suck
@bekindalways7629 3 жыл бұрын
Is the process same to 2017 rdx which i plan to DIY
@jasony9950 4 жыл бұрын
I just got done doing this today, using your video and the Acura instructions. Not hard as some people think, just follow the instructions and watch your video from time to time. Took me 2 hours of work with no knowledge of the car before. And that’s including putting everything back together. Now all I have to do go to Acura. I was told if I bought the remote start from Acura they will do the I-HDS for free. Just show receipt. Not confirmed yet because I haven’t gone. For those of you who are scared to do this, it’s not hard. He did a great job showing the process, and the instructions are very step by step. Thanks again man!
@visualizediy3920 4 жыл бұрын
Thats awesome! I'm glad I helped. I actually did this for our Acura forum community. During the install, I realized there was no need to fully remove the side trims; this helped a lot. Just tape up the upper trunk trim to protect it from scratches and we are good to go.
@stevepen 4 жыл бұрын
17:28 Couldn't you have popped that top panel out without removing the entire back of the car? Looks like the sides tucked in under the side panels, but it looks like you could have just popped the top or each side out to get the top piece out. Looking back, could you have did that or no? BTW, did you end up with any scratches/rattles when you were done?
@visualizediy3920 4 жыл бұрын
Nope, the side trim needs to be removed to release the upper trim in the back. The only area that scratches could occur is the upper trim while taking it out. I recommend taping it before trying to remove it.
@stevepen 4 жыл бұрын
@@visualizediy3920 Thanks for the reply. Its a shame they didn't put in an access panel or put it behind that panel at the top of the hatch itself 6" away from where they put it.
@jayb0nd007 4 жыл бұрын
I would never do that he is a professional he started it in the morning & was done in the night & was missing the part where u program the remote to the starter,
@visualizediy3920 4 жыл бұрын
Hey Jay, I got the programming done at Curry Acura. It only took 5 hours :). It took so long because of filming and going slow.
@deadangel6142 4 жыл бұрын
Where do you buy your remote start star for $280 ?
@visualizediy3920 4 жыл бұрын
www.alldiscountparts.com/oem-parts/acura-remote-engine-starter-08e92tjb200?origin=pla&gclid=CjwKCAiAzanuBRAZEiwA5yf4uhAGakHZTYCn-Oi-4Y6wUyEI2m_14GZXEdF7Ayin1W1IbOKzrHGnSxoCsbkQAvD_BwE
@kerryrichards4987 5 жыл бұрын
Dude I would pay you to come to the Caribbean and install mine. That installation looks hella scary.
@visualizediy3920 5 жыл бұрын
It looks hard but its not that bad :). Just be patient and you will get it done.
@navyryder 5 жыл бұрын
Nice job, man, I would be scared of doing it myself, I know , I would scratch something or worst break something, them plastic panels always seemed to weak for me.
@visualizediy3920 5 жыл бұрын
Honestly, the plastic panels were solid. They will not break easily. Nevertheless, the plastic clips can break if you don't line it up properly to the body panels. It is hard to mess up though. The hard part was installing the receiver above the headliner. The installing space wasn't much but with patience, you can get it done. As for scratching, you just need to tape it up with packaging tape on the side of the plastic panels; this will help prevent minor scratches the plastic.
@jolsen0717 5 жыл бұрын
That’s the most ridiculous thing I’ve ever seen, all that work for a simple remote start!? The new RDX is lacking in remote start and wireless charging. Shouldn’t have to relying on the mobile app for remote start, it should be included on a luxury vehicle. Just my thoughts...
@in2zion478 5 жыл бұрын
Yeah, it was a lot of work but I am now enjoying my remote starter. Although the Acura Link app has other advantages, day-to-day usage of the starter on the remote is necessary for me. It just faster to start the car with it. Nevertheless, you really need to test drive the car. The fun factor of the car allows me to forgive Acura for their mistakes :) .
@davidrulnick7257 2 жыл бұрын
Remote start is included on the Advance trim level and the new Aspec Advance trim. Or just use the on line remote start through your cell phone, it's brt5than an old fashioned key fob remote start because yo8not limited by tange.
@sjbdrums1969 7 ай бұрын
@@in2zion478 how is the range on the fob? I've heard it's horrible.
@user-cp7wh4dk9b 5 жыл бұрын
How did you program the new keys to your car? Or did you just take it to the dealer to program the new keys? If so, how much was reprogramming? I bought my kit and this video helps a lot.
@visualizediy3920 5 жыл бұрын
Nice, let me know if you have any questions. I'll be glad to answer them. The remote keys needed to be programmed by the dealership; a regular locksmith group cannot do it yet. It cost me $140 with taxes at my local Acura dealership.
@Light23K 5 жыл бұрын
I’m more surprised that the USA version don’t have power side folding mirrors and the Canadian models do. Makes 0 sense and the reason I held off on buying one. I can’t support stupidity.
@visualizediy3920 5 жыл бұрын
I totally agree. I really don't understand either. I do not know which focus groups may have recommended these changes. I always used the power folding mirrors and the remote starter on my MDX. Nevertheless, the RDX is a blast to drive. I love it!
@margaretfarkash2113 3 жыл бұрын
I don’t get this why would you take off so much paneling if you connect it to the battery and btw my 2017 rdx advance came with remote start
@RANDYP501 5 жыл бұрын
Great job, not sure if I would take it on! Sucks that this isn't already installed and all they would have to do is program the key fobs. Did you buy remote start from the dealer?
@visualizediy3920 5 жыл бұрын
Yes, I purchased this directly from a Acura dealer. This dealer provided the best deal for it: www.factoryacuraparts.com/v-2019-acura-rdx-5-door--aspec-sh-awd--automatic/accessory-components--remote-engine-starter I just got it programmed yesterday and it worked...thank goodness!
@jimccc9467 4 жыл бұрын
So did the $284 price include all parts needed including fobs? Or did you need to buy additional items? Nice job on install.
@visualizediy3920 4 жыл бұрын
@@jimccc9467 As for the actual install, no other equipment needed. You will need some tools though...like the trim removal kit. It will help.
@jimccc9467 4 жыл бұрын
Visualize DIY I bought one for my daughter’s ILX, wish it was as simple as yours. For the ILX the instrument cluster has to come out which it fairly involved and ultimately I will need to pay a locksmith to come and program new fob because the original ones will no longer function to start car.