Can you explain how to hook up subwoofers...matching hz etc...wiring. Thx
@johnnyplemons2 ай бұрын
What do you want to do with them? Increase resistance or reduce resistance? To increase the resistance wire in series, to reduce the resistance wire in parallel. Frequency or Hz. doesn't really play into it. Although it is true that the impedance of a speaker changes with frequency, you wire for a nominal resistance. For example wiring two 8 ohm subs in parallel will give you a 4 ohm circuit, you basically ignore the resistance changes caused by the frequency. Likewise wiring two 4 ohm subs in series will give you a 8 ohm circuit. Speaker resistance is normally taken at 1000 Hz. which is how the impedance rating is determined 8 ohms at 1000 Hz. When measured with a DC ohm meter you will always get an impedance of less than the impedance rating of the speaker, DC is zero Hz. an 8 ohm driver will read somewhere in the 7 ohm range, a 4 ohm driver somewhere in the 3 ohm range.
@jaxmg10 ай бұрын
Hey! WHats the connector you used to connect speaker to a wire called?
@terrylouis134110 ай бұрын
Stupid video
@bahaknp332 Жыл бұрын
where do i connect the headphone jack???
@johnnyplemons Жыл бұрын
Head phones need to be taken off of a low level output, such as off of the preamp circuit of the source.. They are not designed to be used off of speaker outputs, you can fry them that way.. IF you do use them with the speaker output, I would make sure to add a 500 ohm power resistor inline with the headphone jack.. Something that would handle at least 50 to 75 watts, that should give you a good level of protection for the head phones, and could make them useable at the same time. john
@gabrielorey9052 Жыл бұрын
Exelent 😜👍
@MT-rg4dm2 жыл бұрын
Why would you want to do this what’s the advantage to putting them and series what do I gain. And is it necessary for two speakers or is it strictly for multiple speakers
@theflash11852 жыл бұрын
It doesn’t matter how many of these videos I watch I simply just do not understand series wiring or ohm capabilities of the speakers I just bought. The American educational system has failed me lol
@CookNComedy2 жыл бұрын
How do you place the tnuts with damaged holes?????
@CookNComedy2 жыл бұрын
Wow, i was hoping you showed how you did it on the damaged speaker box.
@lovelygaya2313 жыл бұрын
Size Nut
@oOohdaddy3 жыл бұрын
Just quick question so im clear i have front door speakers 4ohm and rear ones need to be 8 but i didnt buy 8 ohm i bought 4 do i need to return it or can i wire it to become 8
@johnnyplemons3 жыл бұрын
Yes, you most likely will need to exchange them for 8 ohm drivers if that is what you need. You can wire the two 4 ohm speakers to achieve 8 ohms, but you can not change a single 4 ohm speaker into 8 ohm speaker. You can add a resistor to it and electrically get 8 ohms, but it isn't a practical solution, depending on the wattage you are driving them with, the resistor can be fairly large.
@oOohdaddy3 жыл бұрын
@@johnnyplemons thanks a bunch
@luisin3211233 жыл бұрын
Is 300 rms per crossover?
@johnnyplemons3 жыл бұрын
Yes each crossover is good for 300 Watts Per channel, RMS, not peak. Instantaneous Peak is more along the line of 500 to 600 watts.
@lifewithkeith3103 жыл бұрын
What the alley key name wat the bolts size
@johnnyplemons3 жыл бұрын
Not sure about the exact Hex key size, but the tee nuts are 8-32. That would make the Hex Key somewhere around 1/8" at a guess, See www.mavin.com/store.php/hardware-and-misc-products/speaker-hardware-kit-6-tee-nuts-w-6-socket-caps-1-8-32-screws for a complete kit of 6 pieces..
@MrKockabilly3 жыл бұрын
This is an explanation how t nut works but I'm sure this was not able to mount the speaker in the picture.
@johnnyplemons3 жыл бұрын
Yes, I was able to make a repair on the speaker, there was enough material left to make it work.. john
@pankajtiwari67273 жыл бұрын
Mujhe chahiye
@ImKumii3 жыл бұрын
What if I have amp that supports 4-16ohms speakers and I have 2 ohm and 8 ohm speakers = 10 ohm in total (in series). Is this OK or do I still need the speaker to have at least 4 ohms?
@johnnyplemons3 жыл бұрын
If your Amp supports 4 to 16 ohms, and you end up with an impedance that is within that 4 to 16 ohm range it should work fine..
@negativegiraffe20363 жыл бұрын
I have two 4 ohm speakers . If I wire them in series are they still in stereo ?? Its a stereo source ..
@johnnyplemons3 жыл бұрын
No, you would need to have four 4 ohm speakers to keep the stereo, doing it that way you would end up with two 8 ohm circuits. One for the Left channel, and one for the right channel.
@negativegiraffe20363 жыл бұрын
@@johnnyplemons Thanks John
@arjanindindiausaisoiatfcer28004 жыл бұрын
Arjan Industries manufacture components like Compression Limiters & Threaded Inserts as per requirements (Drawing) www.arjanind.com
@morkthebuilder99434 жыл бұрын
brilliant. simple but helpful
@xynstav4 жыл бұрын
How you know witch wire from your car is negative and witch positiv
@johnnyplemons4 жыл бұрын
It changes from car to car, due to the color choice of wire, there isn't a common way of knowing. Try doing a search for your specific vehicle. Or use a multimeter to get your answer.
@motorheadbanger77204 жыл бұрын
Do you think the same would apply if I used a Tnut on plastic mass? Thanks
@johnnyplemons4 жыл бұрын
Sure you can do that, but with a slight modification. The Tee Nuts for wood have teeth that grab into the wood and embed themselves for use. For plastic, use the tee Nuts without the teeth, and then bond them in, epoxy or some other bonding material to make them work for you.. I can see it working. john
@motorheadbanger77204 жыл бұрын
@@johnnyplemons amazing! Thank you very much
@goldenmelodies89274 жыл бұрын
Ples add written documents in along with video it's very helpfull
@jonienglish32314 жыл бұрын
Good Video Question now i have 6 speakers + a Subwoofer in my Tahoe i want to ADD 2 more in the Rear Quarter , to make Total of Eight . would it be in Series or Parralel
@electromavin4 жыл бұрын
There are some variables to deal with.. You will need to understand what impedances the stereo in your Tahoe is working with. The best and safest answer is series which will not blow up your stereo. It will add resistance to your system and thus reduce the power output of the source, but it will also not blow out the amplifier, so it is safer. There are many factors that you need to take in account. You can fly by the seat of your pants and just add a pair and see how they sound, but you may or may not shorten the life of your system. That said, you can replace other speakers with lower or higher impedance drivers to balance out the system to where it needs to be in order to keep everything at the proper impedance. It will take some planning to do it right, and you may end up with a series parallel configuration once all it done..
@jonienglish32314 жыл бұрын
@@electromavin the Original Tahoe just had 4 door Speakers and 2 Tweeter on Dash , a Sub Woofer was added with a Line OutPut Converter .to the OEM Amplifier . but SOUND is Cutting out Over Bumps - i suspect Somthing id Shorting out under the CONSOLE - will take appart when Weather Gets Warmer
@akosipetmalu62474 жыл бұрын
This man is too shaky!!
@RawbAtLivedotca5 жыл бұрын
if im hooking up two 8ohm speakers in parallel to become 4 ohm and i want to add a tweeter which is 4 ohm to the the left wire will the tweeters stay 4 ohm? also can i add the right side speakers to the same input pos and neg to have both side wires bridged.
@bautistaconcon57195 жыл бұрын
I have 500wattst amplifier, it has 6 to 16 ohms on the output speaker's terminal, I want to connect 6 speakers per channel, how many ohms and watts of speaker should i used and how to connect them,thank you and more power,.
@supremo30245 жыл бұрын
what the size of t nuts use in speaker mounting?
@sanjoy25215 жыл бұрын
I want to make an 8 ohms 30 watt speaker system. Can I connect one 4 0hms 20 watts with one 4 ohms 10 Watts in series to make 8 ohms 30 Watts speaker ?
@johnnyplemons5 жыл бұрын
Sure, electrically that would work, but there is a bit more to building a speaker than just throwing a couple of speakers together. But if all you want is a speaker that will handle 30 watts, that would work.
@sanjoy25215 жыл бұрын
@@johnnyplemons Thank you Sir
@androiddrummer85545 жыл бұрын
palco amplifier inside view
@madhukumari-jd4qi5 жыл бұрын
very good
@technosoft47415 жыл бұрын
kzfaq.info/get/bejne/beCKard3u96XeGw.html
@bradowens40525 жыл бұрын
So can you double check the resistance via a multimeter?
@johnnyplemons5 жыл бұрын
Hi Brad, you can always check a speaker with a multimeter, but you will only get the resistance at DC, Speaker as they go through a frequency range, will change resistance. So a speaker at DC will have a resistance, a speaker measured at 1000 hz. will have a different resistance. SO your measurements will only give you an idea of what you are working with, not an exact.
@78goldenking736 жыл бұрын
so ur not smart .... come on we all know this .... n found that long time
@mtcremake58626 жыл бұрын
Wat will happen if you connect the speaker to monoblock
@rohitkumer98276 жыл бұрын
Hello bhai jaise speaker me coil huta hai jaha speaker ke dono wire lagati hai bahai bahar me ciol fetting kar do toh chela ga
@johnnyplemons6 жыл бұрын
हाँ
@johnrodriguez65796 жыл бұрын
K
@erdogannayir25576 жыл бұрын
Various types of nut screws for wood. I want to sell in Turkey. Mail : [email protected]
@marcmarcello9816 жыл бұрын
You shouldn't wire speakers in series, all you will get is the cones flapping when even the slightest amount of bass is applied.
@sanjayghosh3916 жыл бұрын
Valo
@RobPGamerVaper6 жыл бұрын
Can I ask you if I have a Speaker that has a Dual Voice Coil its 2 ohm and it's 400 watts RMS I want to wire it to 4 Ohm would the speaker still be capable of producing 400 Watts RMS ?
@johnnyplemons6 жыл бұрын
If each set of voice coils is 2 ohms, you have 2 positives and 2 negatives, run a wire from the positive on one set of hookups to the negative terminal of the other set of hookups. That will put the two voice coils in series. It will still be able to handle 400 watts RMS
Great video I have been trying to figure out how to build bipolar surround sound speakers I wanted to use 2 4inch 4ohm aftermarket car speakers with my 7.1 amp that takes a 8ohm load. This video did the trick thanks
@tylercardenas45206 жыл бұрын
dose any one know how to wire a built in speaker electric guitar to the out putjack
@jasonhuber32367 жыл бұрын
Thanks for posting this! I've been relying on the MDF for anchoring since I've been alive lol. My sub box is in desperate need of these and I'm going to Home Depot tomorrow to get some. Not sure why I never thought of this. Again, thanks!
@petegreen51127 жыл бұрын
wot can i say. ill tell you just that!!!!!!!!! it is very strate forword 2 speakers at 4 oms in parallel would give you 2 oms / 2 speakers in sek would give you 8 oms. TOP MAN could not put that better my self.
@mathiasgrenander94407 жыл бұрын
I am the number 1k subs
@ivywang93217 жыл бұрын
Hi, this is Ivy. Do you import T-Nuts? We are manufacturer and exporter of T-Nuts.
@pedropanta2557 жыл бұрын
On my 2006 Honda Accord'rears speakers I have at RR,blue-yellow and pink wires on RL I have blue-white and blue-black,I want to know which one are positives and negatives
@electromavin7 жыл бұрын
I found this on Auto Zones website.. It shows that the Pink is Positive, and the Blue White is Positive.. repairguide.autozone.com/znetrgs/repair_guide_content/en_us/images/0996b43f/80/24/c5/38/large/0996b43f8024c538.gif Hope it helps john
@pedropanta2557 жыл бұрын
Thanks,it will help me
@tonygreen43767 жыл бұрын
One of my speakers it's getting very hot
@electromavin7 жыл бұрын
Not exactly sure what that could be?? It could be that the driver is being over driven, that is to many watts being sent to the driver.. A driver is designed to handle a specific number of watts, for example 20 watts, if you are sending 40 watts to the driver, it can run hotter, since you are sending twice the power.
@MrAlbonit7 жыл бұрын
fuck ya allll i just burned half of my house trying this shitt
@electromavin7 жыл бұрын
You did something wrong, and it is not related to what was being taught in the video. A series connection is one of the most basic circuits, and only going to the most extreme of applications are you going to have a fire. The speakers voice coil would burn out long before anything would burst into flames. The temperature would need to exceed 451 F to cause a fire, so you would need to go to a very extreme point with a speaker to cause a fire. A very very extreme point.Sorry, can't really envision your issue and how it applies to this video.