Hello, I need some help. I had removed the crankcase cover and put a new rubber gasket on. when i went to reinstall I noticed i still had a small gap along the left bottom side. its like a quarter inch off.. its so strange because theres nothing in the way and everything is clear. Is that supposed to be like that?

Hi Tony ı am from Turkey.I have a Honda Helix cn250 1996.Do you have a Instagram or Facebook. Because ı need to ask something about fix my Helix thank you.

Good morning Tony! My caliper pistons wont retract.. I've pulled it apart, cleaned it, put new pads on it and it they're still sticking. What should i do!!

Great helpful tip! Thank You!

Hi them botom cooling hose from carburetor going whear? Thanks

Hi whear them down one cooling hose from carburator it going?

Hi wher them pipe from whater pump connecting?

Thanks gotta change mine soon love your videos bro

Where did you purchase that radio?

Can it work without remote control, please??

Thx, nice video.

I would have put the bracket on the inside of the fender so it would have been more hidden and probably easier to have worked on...lol.

Pb blaster would work better, it's a penetrating spray. Wd-40 is a water displacement spray.......of course you know this........gotta use whatcha got😊

Do you have a video of you connecting the right side switches on handle bars? I bought mine with no switch and I have a blue and white wire beside the ignition wire harness. Been told it’s for the trigger and reason for no spark. Can you please help?!?!

I'm a retired P&G plant technician and I've only seen purple, green, blue and red loctite. Is orange something new?

Having that over sized tire on there caused all of the problems you encountered Tony. There was at least a 1-2 inch difference?? Thats why that hole was wallered out and those bolts were stripped, That was just way too much of a misalignment. Great job on fixing it👍

Hello, Tony, the clutch shaft has axial play, not up and down, but the clutch can be moved towards itself, what could be damaged?

Great job Tony.

Tony where did u purchase this seat cover? I am now trying to decide if I want to try this or go get it done. Thanks

Definitely don't need to take all that off just for the carb

Tony, I can’t get the rear wheel back on. What can I do??? The splines seem to not match up now?

Thanks very much Tony, very informative. I have sold my Helix and now have the Reflex.

Hi Tony, I am having an issue with popping on deceleration and I have to set the idle up higher than normal or it will stall. Idles up and down on its own. Other than this it runs great, great acceleration with no hick ups at all, tops out at 71 mph. I The carb is a china one, the jet I noticed is a 108 not sure on the low speed jet right off hand. My brother has a helix with a stock carb and his runs perfect, I took his off and put it on mine and it ran like a new scooter so I definitely know the china carb is the issue, what size jets would you recommend that I put in the china carb to possibly solve my issues? Also do you know how many turn out I should be on the air/ fuel mixture screw?

Tony, these videos are super helpful, thanks!

How many miles did you put on those break pads ?…they looked still pretty good. Thanks for the vid 👍🏻

MORE HONDA HELIX VIDEOS! (please) 🙂

What battery do you have in it? Ive done tons of research and found nothing on an upgraded battery.

Brasil 🚛🚜👍

Thank you for this 🫡

Hi to my cn I only put 150ml as reported in the manual, and watching this video I saw the oil dripping. My 150ml didn't drip so you put more or I put little thanks

Can you tell me the tire measurements, greetings and thank you

I’m sorry if I missed it but once you upgrade the jets and get the pod filter on is there anything you have to do to the original airbox? The snorkel will be off

If you replace pod filter with out replacing jets, will that be okay ? Or is that step required for this to be successful?

Hello, could you tell me the model of the tires and where to buy them, greetings

pause in the beginning of your fucking* video that you don't know what you're doing your battery is not charged and you don't have a clue about what the process is

Thanks for the video!!!

Thanks, Tony! Works great on my Helix!

Thank you for your great how to video's ! They are great help to us amateur's ! They do help me do things on my scooter ! Thank you !

Tony you are the man!!

Hi u need to remove the sleeve and there will be 3 pins u can remove and it all comes apart. It will need to be lubed to perform its best.

Hi Tony , Sorry to bug you again , but I've encounter another problem with my scooter . The starter motor rotate freely , but doesn't engage the flywheel , hence the engine doesn't move . Do you think the problem is the starter motor , or worse , something got loose or broke behind the side cover , where the engine oil goes ? I've removed the starter and turned on fine , but I'm not sure if the shaft of the starter must move out when giving a crank , like a car bendix , and then retract back ( mine doesn't move ,just spin ) . Any help would be greatly appreciated . Thanks.

will a cheap secondary clutch work just as good or am i better off rebuilding ,, just trying to do it the easier way without breaking the bank lol

cool!

Peace

thanks for another helpful video ..

Brasil 🚜👍

thanks for all the Helix content Tony!

I used a zip tie to hold the lever down, open and close the bleeder, remove the zip tie, and release the lever to bleed on my own. Had to do that a few times and worked pretty well.

Dude where do you get the master cylinder I need one ! Information please !

I have an 86 that idles smooth as silk but on runup, it has a terrible bikewide vibration that rattles the bike ad high rpm. Any thoughts? I have a new variator and clutch and belt. My "guess" would be worn motor mounts. It only has about 8K miles though. Appreciate any thoughts.