Did this happen to get rid of a ticking noise if you had one?

Great video,your son will appreciate all this knowledge.

Your series of videos on the 160 is a real help. Thank you very much.

I only subscribe because of the dog

This is helpful, and my electrical is just like yours, but the cord isn’t long enough to reach it!

Nice 💛

14:05 part with cable still attached, 14:09 its off with no video to show how.....

Thanks so much for your camera work. I’m an older women but still love working on 4 wheelers and I have a Suzuki 160 that needs these clean ups.

Drill it out with a vacuum cleaner in place to capture the drill dust and chips. You did a good job on that. Perfect example of why all the thread holes must be checked first.

Spray the bolt hole with wd40, and run the intake bolt in and out first, before putting intake on

Mine blows for a few seconds then starts slowing down on its own until it turns off completely. Could be blower or resistor?

thanks for sharing my man... great video..

En español

Looking for good shocks for my Veloster base 2016, any recommendations

can you please tell me the size of socket you used? was it a 17mm or 19? Also, I have a son your son's age and I loved the dynamic there going on, great dad teaching a young man to that type of labor, two thumbs up to both there. great work, also liked very much the camera work, steady, good focusing etc, congrats!

Can this be done without pulling the engine without a gigantic amount of headache? I’ve got a lift, I feel like it’s doable, but I haven’t found any examples of people doing it this way.

kzfaq.info/get/bejne/kLN0mM9llduyfmQ.html

I have a hyundai veloster 2012. So I am going to subscribe, I feel your pains in this car bro LOL

2 Quarts = 1.892 litr

congratulations, good video and good instruction

Bout to go do this on mine... great video man.

Why do we need to know how to jack up a car and drive to Walmart???

I have a ? Wat is the plug on the other side of the motor for

24 inch pounds?

Needs a timing chain tensioner. I just fixed mine.

A good dad for teaching your son how to do his own work.

On the passenger rocker arm assembly, you had readjusted and said that it was not aligned exactly. Were you speaking on the rockers not centering on the valve?

I’m in a very similar situation, I have a port that needs shaving on the bottom edge to fit the rear passenger bolt. I watched your video as I was preparing to apply RTV to see what I needed to look for. After watching your binding/fitment issue I decided to test fit the intake without RTV and discovered the need to shave off the lower section of the port to clear the bolt. Unfortunately the heads are bolted down so I will be going at it with a dremel and vaccum. I think you said you applied RTV to bolt hole, is that right? For reference these are 4.0 iron ITM brand heads. Bottom passenger port for intake bolt needs additional material shaved to fit bolt.

Your channel makes me sad. It has superior information that is USEFUL yet only 440 subscribers. The sad part is, if you were making an informative video, then going off and doing something insanely stupid with it, you would get more. (please don't do that btw) Most of the comments too, they are from people like me that just want to know about their machine. I too have an LT 160 that I am desperately trying to make run. I need it to go from where I live to where I get essential items like groceries and meds 8 miles away. Walking that 8 miles is brutal. It's late may and already 100 f outside during the day. Watching what you have done to make your LT 160 run tip top has been very informative. Thank you. KZfaq needs more like you.

fabulous...i knew there had to be a trick. since i did one side, when other side hub wouldn't come off, i pounded the shaft for the lever, thru from the inside, and it worked.

I have a stock airbox if you still need one. I went with a pod filter. I’m also looking for the plastic piece that goes between the two front fenders under the headlight.

Where is blower motor

I checked all the wire. But no spark. How can i check the cdi?

Good dad right there.

First of all great video , very helpful. It looks like I have the same carb. How would I go about getting a rebuild kit? I can’t read my vin to find out my year of my 160. The only thing I can read is Mikuni 02c 02 on the carb. I looked it up and can’t find anything on the last part of 02. I just want to order the same exact rebuild kit that you did.

Hi there, how did you block off the choke hole, please explain how u go about doing it, as I want to disconnect my choke, it's a pain🤦‍♂️

Where did you get the part?

did you pull the oring out of the fuel screw?? you put the washer on the fuel screw on top of the spring its supposed to go under the spring against the oring

Do you know what part I’d need if the old owner cut the connector that plugs into the blower motor

If your Corsair Harpoon has a double clicking issue it isn't because it's dirty it's because it's a bug with the latest firmware update 3.13, to fix this you'll need to search up corsair harpoon double click fix and you'll find an easy to follow guide.

Is This the same process for a 2012 basic Veloster?

Good video…good seeing you teaching him…learning how to fix cars will help him a lifetime…

How do throttle cable from the kill switch

stock air box intake is on the top frame tube (the one that runs just under the tank) I find that's plenty high for going through like 1¹/2 ft of water or more

Helpful video, i just want to know where did you buy the shock, name of the brand and model number? Because i also have issue with ny rear shock

Make sure you guys and gals are SUBSCRIBED! New LT160 content is on the way soon!

hey cool guide. have you ever opened the radioator with the pump to clean? I have a Bykski B-FRD5700XT-RBW AIO and the pump is getting very loud, i was told to open it and clean it, but have no experience and afraid to damage. can you suggest a guide? thank you

I've got a yellow 83 model that looks just as good.

♥️♥️♥️♥️♥️♥️♥️♥️♥️

Hey man, love your videos. Can i ask you which size are the front wheel bearings ? Or the code number to look for them. Thanks!