I have a 2021 Tiguan a I was unable to retract the EPB I even called tech support and they walked me through the steps and still wasn’t working
@rdh205929 күн бұрын
Shock and amazement at the use of a FRAM oil filter... LOL! You went to the trouble and expense to rebuild the engine the right way, then used one of the cheapest oil filters around? At least go with a Wix...
@CarsBikesandCoffee29 күн бұрын
I know appalling 😂never shocks me when I put one on just to see what people say to change it shortly after. No harm no foul, appreciate you watching! 🤘🏻
@rdh205929 күн бұрын
@@CarsBikesandCoffee Honestly that first oil filter, as you know, is only on for a short while, to clean up any gunk/shavings/filings/etc... that remained in the engine. Great work on that car. Your videos capture the essence of what your doing without the hours you spent doing it... Excellent work on this video... Still shivering over the Fram filter though...
@CarsBikesandCoffee29 күн бұрын
@rdh2059 thank you!! Rest assured that filter came off right after the video 😏
@600milesАй бұрын
1:36 if you sandblast the parts they will never have the original gloss finish, will be dull and abraded looking unless to buff it.
@CarsBikesandCoffeeАй бұрын
Very good point, thought I made a comment about that. But yes, if you want a matte plate sandblast, if you want that gloss, I brass wire wheel it.
@mikegadoury6172Ай бұрын
Hey Curt - great video as usual!! Appears you hit a bump in the 260Z project. Is it going to start back up again? Great content - I've watched your L series engine builds numerous times. I'm getting close to that point in my build
@CarsBikesandCoffeeАй бұрын
Appreciate the support! It will be coming back had to put it to the side for a bit. That is awesome! Pretty soon you’ll be cruising!
@XgvHihkАй бұрын
❤
@fastdude2002Ай бұрын
My first car at age 16 in 1983 was a very clean 1973 240Z. Same color interior as this one with the outside being white. Wish I still had it, fun car.
@ReputacionMedica-no7xiАй бұрын
Help! Boot loop My ArtiDiag 600S went into a boot loop and I can't reset it. I've tried the reset button but nothing happens. Please help! Great review, by the way!
@matthewpeterson33292 ай бұрын
A co-worker just bought this unit and we are going to be comparing it to the less expensive NUCAR scanner. So far, the NUCAR has been pretty handy. It's bi-directional and will also update itself for whatever vehicle you are working on. The larger screen on the 600s is very nice.
@malik.b304210 күн бұрын
Which mucar?
@matthewpeterson33297 күн бұрын
@@malik.b3042 Mucar CDE900
@Z32orDIe2 ай бұрын
Funny this video is for the z32. Im about to do this. Z's been sittong for 7 years straight. Fuel pump hanger was so rusty that the ppwer and ground wires rusted off the inside of the pump assembly and were just dangling in the air inside thw tank. The level assembley was rusted it wouldnt even move. Completle setup was bricked. Had to replace eevrything. Gonna try cleaning injectors since insides are stainless. But if dosent work will replace. Love these cars but damn they got neglected by there owners. Wtf.
@Michael-xy5ur2 ай бұрын
can you tell me the dark gray color name and brand (supplier) on your 240z?
@CarsBikesandCoffee2 ай бұрын
That is Toyota Magnetic Grey
@Michael-xy5ur2 ай бұрын
@@CarsBikesandCoffee Thx mate.
@Joeisverygood2 ай бұрын
Where is your master cylinder resovoir?
@CarsBikesandCoffee2 ай бұрын
Removed it as it was leaking and then left it out to work around the back of the engine. Long form video on all that, back in now, video soon!
@ronarndt67222 ай бұрын
Great video! and thanks for showing how to adjust the float assembly too.
@terryatpi2 ай бұрын
Belleville washer ?
@PhantasmPhoton3 ай бұрын
thanks for posting this its an incredible resource
@cleanthesea3 ай бұрын
Your radius rod washers are the wrong way round
@CarsBikesandCoffee3 ай бұрын
Yeah, shortly after making the video I realized with some help. There’s a note in the description I made back then about it. Thanks for pointing it out though!🤘🏻
@cleanthesea3 ай бұрын
@@CarsBikesandCoffee I was a little last with that comment. Hope I didn’t come across rude. Great work though. I’ll see how I get on but mine have been good with Poly on both sides. 👍
@kirkgreenman13863 ай бұрын
Are the Z mirrors interchangeable from right to left?
@javierb.98923 ай бұрын
The bolts that hold the sway bar to the body of the car are the ones that get torqued to spec with load on the vehicle, not the endlinks. Per the factory service manual.
@dalemihocik47324 ай бұрын
This tool needs to be Bi-Directional also.
@keithhillard14 ай бұрын
Can you view wheel speed sensors live data with the 600s?
@amilkar194 ай бұрын
How long does battery last??
@Michael-xy5ur4 ай бұрын
Hey can you give me information about those wheels on this build? Thz
@CarsBikesandCoffee4 ай бұрын
They are Rota RB 17” x 7.5” up front and 17” x 8.5” in rear with a +4 offset. Tires are 225/45/17 front and 245/40/17 rear.
@68pishta684 ай бұрын
@20:46, you state the plastics should be 35mm from bottom to top. The plastic floats are 27mm tall so that only leaves 8mm from top of float to top of lid. Does that sound correct? I see 18mm clearance from top of float to lid so that would be a 44mm total bottom to top referenced in other places. Confused.....
@erichschinzel64865 ай бұрын
I had a 300zx TT...the harness is crap...I learned the hard way
@CarsBikesandCoffee5 ай бұрын
Oooph no fun.
@christophersalles67785 ай бұрын
How do you know if you should clean/rebuild or replace?
@CarsBikesandCoffee5 ай бұрын
A few ways to see this The way I look at is if it’s running rough no matter your adjustments, a clean and rebuild is essentially “cheap”. If you don’t feel comfortable rebuilding, replace. If you feel comfortable, but for example butterfly bushings leak air or are worn and can’t replace the bushings, replace. High level approach of course.
@nwrob15 ай бұрын
Excellent tutorial, thx. I guess voltage doesn't matter here? Oh, and you're not kidding about using muriatic acid in a shop environment. It can rust everything in the shop overnight. It can be a real disaster - heads up people!
@E3DaDrumma5 ай бұрын
Can you show where all the engine bay grounds are…
@CarsBikesandCoffee5 ай бұрын
I’ll put that in the next video!
@E3DaDrumma5 ай бұрын
@@CarsBikesandCoffee I appreciate it brotha
@FairladyS1305 ай бұрын
Needs wifi to work.
@johno-gb7ci4 ай бұрын
I'm sure you do
@southernvetsweets49295 ай бұрын
Do you have instructions on prepping the yellow chromate? Do you buy it ready to go or is it mixed/diluted?
@CarsBikesandCoffee5 ай бұрын
I use Caswell’s solution which you mix. I highly recommend their book/manual you can buy, very helpful.
@gefflynn71715 ай бұрын
Man, great vid! Can Relearn procedures be performed with this tool also? For instance, Subaru CVT Relearn. Thanks
@motavice34995 ай бұрын
Thanks ao much for taking the time to create this video! Very helpful!!
@BoulderCreekSteve5 ай бұрын
Why must your generation constantly flap your wings about as if you are a spasmodic albatross attempting lift-off? I am sure you’ve never taken a public speaking course? If you had, you’d certainly have learned that it’s very easy to annoy/turn-off your audience, so that, no matter how good your content, the distractions make them tune out. So is the case with you.
@CarsBikesandCoffee5 ай бұрын
😂
@mdjamelmdjamel62805 ай бұрын
Co nice
@someonewhopretends6 ай бұрын
Nice swap, are you sure that one of the half shafts is shorter? There’s lots of convoluted info regarding this and people claim that they are the same length?? What seems to differ is length of stub axles, the one on the driver side is shorter for r200
@williambuchanan82046 ай бұрын
Very helpful mate. Appreciate it
@kkendall98886 ай бұрын
Maybe this was addressed in one of your previous videos but at this point why not just pull the motor?
@CarsBikesandCoffee6 ай бұрын
Yeah, I agree. I would have probably got it all done quicker and not suffer through some it.😂 thanks for watching!🤘🏻
@shefbistro7 ай бұрын
I have a mud pump cylinder from 1890 and I cannot remove piston . It is 1 inch thick and 7 inches in diameter. I need a help. It is a duplex mud pump cylinder from Gardner Denver.
@yobringitondown55657 ай бұрын
I have a R200 that I could install but finding 3.70 or 3.90 gear sets is simply impossible. Can’t find one. And my diff shop can’t find any either. Anyone have a source?
@84tanlile7 ай бұрын
I wanna see the house. That roof triangles look amazing
@TheCustomEverythingChannel7 ай бұрын
Dang nice job 👏
@user-do6kp7yk6s7 ай бұрын
Great video. Thanks for sharing! I also need to do the O-ring on the striking rod shaft at the rear. How much play on the input or output shaft is too much? Mine moves about a 1/16 of an inch.
@Christ.Consciousness7 ай бұрын
Can you use the camera and have the light turned off or is the light always turned on when you’re using the camera?
@CarsBikesandCoffee7 ай бұрын
Yes it will shut off and is adjustable from off to bright
@rogerbrooks10487 ай бұрын
Which head is this. The chamber shape looks better than other L series heads
@CarsBikesandCoffee7 ай бұрын
P79
@anonysend65327 ай бұрын
It looks great - especially all that plating. How much time per week do you spend restoring your cars?
@CarsBikesandCoffee7 ай бұрын
Thanks! Not enough 😂
@anonysend65327 ай бұрын
Full restorations take forever and I know you've had a few on the go. I'm hoping to complete mine in the next 6 months. Started it 9 years ago...
@CarsBikesandCoffee7 ай бұрын
You’re almost there! I bet you’re stoked
@user-tn1hk6zm2freedom8 ай бұрын
Easiest way to free up stuck pistons is to put about 1" of diesel fuel in the cylinders and light it with a torch. Let it burn out and tap the pistons out easy. Takes about an hour and cheap. Lol.
@nitonas8 ай бұрын
Thanks lots for this video! Been trying to clean/spray-test my Vg30 D21 injectors!!! I follow as you did and succeded, God bless!!!
@christianguillory77858 ай бұрын
Thanks a lot for this vidéo ! On my SU ( front ) a'm unable to repositionning the starter lever ( with the spiral lever ). Your hands are too hight in the vidéo and it's a nightmare... Could you explain to me again 🙏 ?... Best regards
@michaelannen41688 ай бұрын
@6:40 water is thicker than gas. Better to test in gasoline.
@CarsBikesandCoffee8 ай бұрын
Interesting, so you’re saying a hole/crack could potentially not be identified by water but gas would. Good to know! Thanks!
@michaelannen41688 ай бұрын
@@CarsBikesandCoffee oh yes
@tallnrough688 ай бұрын
What are the specs on the cam ?
@_Shimona8 ай бұрын
Beautiful car! Did you do the paint yourself or have it done? I'm thinking about doing a Datsun restore but haven't been able to get prices on paint jobs
@CarsBikesandCoffee8 ай бұрын
I had it done.
@user-yr2ts6vw2c9 ай бұрын
What did you use to plug the other end of the fuel rail? I have side fed injectors and they are becoming a pain to clean and I’d like to do something similar to this setup but if you can explain everything you hooked up that would be awesome
@CarsBikesandCoffee8 ай бұрын
I used a rubber vacuum plug with a clamp, I go into better detail in my long form video. kzfaq.info/get/bejne/gNGCjNB1qJmzl3k.html