Hello! The item does not exists on Aliexpress anymore, do you happen to know what the sensors are called? or if they have a model # i can lookup? Thank you!

Thanks for video, it was a huge help when it came to changing the sensors on my roborock. Saved me a lot of time. It made me proud to repair my robot instead of throwing it away and polluting more. I also saved a lot of money by not having to buy a new one. Thanks!

Any concern about lenses fallong out?

Thank you so much. It would have been so much more complicated to do without your video.

I replaced the sensor for the new from ali express. But error 4 remain. Factory reset also didn't help. Does anybody have the same problem?

Не могу понять. Он их заменил или почистил?

J'aime beaucoup

About to do this with my 2013 15in. Seems like you could leave a little of the old glue in there, and just put the new battery over it? Once the case is closed, I don't think the battery is going to move too much.

it was a very good review. thank you.

Is the turf artificial? I did once home camping and the turf under the tent all died after the tent was removed in 7 days.

can we have a 1 year later review n new walk about video? perhaps street photography 😊

I repaired my vaccum thanks to your video. I feel empowered. Thanks a million times!

i bought a counterfeit Peak Design Everyday Sling 5L V1 & Everyday Backpack 20L V1 a couple of years back. i couldn't afford to buy any original Peak Design products since they're too expensive. the quality is quite terrible as both of the bags had already crumbled now, but it was enough for me to get to know what it's like to use a Peak Design product. i bought an original Peak Design Everyday Sling 3L V2 last year, and the quality was extremely good compared to the fake ones. been using for a year, and it barely made a dent. having familiar with the Peak Design Everyday Backpack design, i finally bite the bullet today and bought the original one. still waiting for the bag to be delivered. if anyone here thinking about buying counterfeit Peak Design products, my advice is DON'T. it will be worn out easily, especially on the zipper parts. it cost me RM500 to buy the counterfeit bags, and now it's just sitting in storage, rotting away. save up and buy the original one, and it will last you for years to come. now i owned 4 of the original Peak Design products since the quality is not something that you found even in a luxury brand products. thank you, YungYaw, for this awesome video! this really takes me back when i first saw this backpack, and i'm still amazed at what it can do.

I followed your steps and my Mac turned on normally, I turnd off yo charge It and now It doesnt turn on again, do you know what is happening?

Awesome

Thanks! I managed to take the sensors out and it was good enough to take their plastic covers out and clean them from the inside and it runs again! 😃 wouldn’t 100% be successful without this video 👍 P.S.: I am a woman, so don’t be worry you wouldn’t make it 🤣

My laptop was son dirty I almost puked.

error 15 is about witch sensors?

Helpful…..thanks!

Where did you bought the battery?

Young.. Good review 📷 Good English 👍

How many months/ years does the replacement last

I am having a similar error on my mop C2 😢

You missed the adhesive remover. Would have made it a bit easier.

ANYone removed this battery and didn't replace with new one ?

Thanks a lot. I was able to disassemble the xiaomi vacuum mop c1 model with these instructions to get to the cliff sensors. The disassembly process there included many more screws and more parts disassembly, but this video has everything I needed for success. Again, Thanks a lot!

So I used you tutorial to get to my sensors but instead of replacing I simply remove the plastic covers from the sensors and thoroughly cleaned them. For some stupid reason they are not hermetic and fine dust finds its way inside. After reassembly the robot works like new and even cleans for a longer time most likely due to a total cleaning that helped it realize better when its not full yet. The plastic covers are easy to remove using my finger to unlatch

Very informative review for me. Thanks. Beautiful backpack but Its not useful bag for camera…

You really need a bag that fits YOUR specific gear or is at least customizable. If it does not, then you’ll have accidents or your camera will be bashed around when travelling.

Thanks for making this review bro! Ni hao.

Wooww nice and cozy home...🤩🤩🤩

I'm a photography novice and just received the Z fc with the 28mm lens, so I'm checking out videos on the camera's controls. Nicely done!

Wonderful video! The images of the video were captured nicely and I wanted to join you for dinner. Kanpai/cheers from the States.

Do you have an updated link for the cliff sensor?

Are you trying to run the robot on black surface's? It will confuse it if you are! I modified mine to work on black surfaces and that's probably what you need to do also! It'll work perfectly then but you wont be able to use where it can fall after the modification!

Hi! New subscriber here from the Philippines. Nice home camp setup! 😊 We're also thinking about home camping for a start because we want to introduce camping to our kids in a safer and more familiar environment. But it's only for a start. 😇

how does the bag look 2 years later??

i cant seem to take out the battery and it doesnt look like im not using enough force? do you have to unscrew something

thank you so much for your post - it has been so helpful

Thank you for such informative review. 👍

Clean and lightly stir collision sesors. I'm getting the error. Nothing clean but not working

Great video, thanks! I have a question ; the same model, I replaced a trackpad, it works, the battery works, but keyboard doesn’t function 😱😳. Any idea of what to do ?? Many thanks

Thank you this was very informative.

Thank you bro

How do you like the bag in 2022? Has it worn well and remained comfortable? Thanks for the demonstration! I hope the lockdown has ended and you can get out and about!

yo no los cambio simplemente los saco, los limpio y los vuelvo a poner y sin p`roblemas

I've got an Roborock E4 with this very same error 4. One of the cables going to the top left sensor was deattached during a previous cleanup and cannot be reattach. Do you know if this replacement would work on this model? I've asked everywhere but haven't had luck so far.

yo, got a link to any recommend battery for 2015 A1502 I can purchase ? or any one I find online will do ?

i won this camera from nikon photography contest