you can if you want, but don't believe they are needed
@netasidhu-jo3qtАй бұрын
That is really good
@patrikhertel9771Ай бұрын
What transmissions did you use? I like it
@d440rc6Ай бұрын
FlySky GT3C Hacked
@archerash6695Ай бұрын
Should have done the demo on a flat rock..
@archerash6695Ай бұрын
Wow a full breakdown of this build and parts lost would pretty cool.
@vhrte49Ай бұрын
Nice job mate!
@antonizarev15812 ай бұрын
what is the WB?
@d440rc6Ай бұрын
around 12.8"
@alans42814 ай бұрын
Good luck with the project.
@themexicanmarauder124 ай бұрын
Where did you order it from. I ordered my through Axial and I’m still waiting.
@d440rc63 ай бұрын
Axial website right at the time they came out
@christersolli31604 ай бұрын
What infill% do you use ?
@d440rc64 ай бұрын
depends on the filament, but usually gyroid or grid with around 20% infill
@christersolli31604 ай бұрын
@@d440rc6 okay thanks👍
@vhrte495 ай бұрын
?
@vhrte495 ай бұрын
Hey mate😊. Do you have the file that clamps on the tyre like you have in this video? I can't seem to find it
@d440rc65 ай бұрын
the beadlock? everything is on Myminifactory, and there's an upgraded version in Cults3d as well, search D440RC
@vhrte495 ай бұрын
@@d440rc6 Thanks mate i didn't even see that🙂👍
@vhrte495 ай бұрын
Do the foams on your upgraded pocket wheel on cults3d just sit on top of the 6 spacer tubes?
@d440rc65 ай бұрын
@@vhrte49 yes
@vhrte495 ай бұрын
Hey mate 🙂 What hardware do i need to get to build this? M3?
@d440rc65 ай бұрын
yes, mostly m3
@2XRC5 ай бұрын
That’s awesome ! You’re talents w unique body and chassis mods is superb 👌
@andrewut7ya5115 ай бұрын
Pretty impressive. I just got a roll, about to try it out. Thanks for doing the tests.
@billwiththeb5 ай бұрын
Hello..how to get the inner harder than outer layer on settings?
@TheMasterizzatore6 ай бұрын
hello, in the end, did you use It for RC parts? i want to do the same thing. thanks!
@d440rc65 ай бұрын
I did, A LOT! Still do, but now I use Nylon Carbon Fiber, it's superior in every way (printing quality, moisture resistance, strength, etc)
@svenjanzen54196 ай бұрын
Hey D440RC, I am interrested in your design ! But first i‘d like to ask you a few things. I have a 6x6 that about 8,5kg. I run 2.2 rims with 1.9 G8 Krawlers. Do you have a Special recommendation for what TPU for inner and outer half to use ? ( Considering the weight ) Aswell as a feeling for how much infill etc ? Asking because I think my rig is ways havier than average. Thanks in advance ! Sven
@d440rc66 ай бұрын
Yes, go Ninja foams! cults3d.com/en/3d-model/various/1-9-ninja-foam-for-rc-rock-racing-u4-and-crawling
What tpu are you using? And how much infill are you doing?
@d440rc66 ай бұрын
Find all the info in my Cult3d page: cults3d.com/en/3d-model/various/1-9-tire-insert-foam
@Rcmorty6 ай бұрын
its not the same as injora. the injora is molded and not 3d printed 😀
@d440rc66 ай бұрын
@@Rcmorty nope, completely different thing - people already know what's better tho :)
@NTX_RC7 ай бұрын
I like it, especially being able to use a fusion still
@2856254177 ай бұрын
do you ave skid for axial capra transmission with dig?
@d440rc67 ай бұрын
I need to check, but think the standard skit might work already?
@2856254177 ай бұрын
@@d440rc6 nope. its not standart like scx10
@d440rc67 ай бұрын
@@285625417 I'll add it
@i_boxed_u-ir8ex7 ай бұрын
Nice work, stoked to print this skid!
@CustomRcCanada7 ай бұрын
Nice design i am looking forward to print it! I already have od in my portals. A good alternative would be to find an offset output shaft transmission and find a way to rotate it so the back output gets higher
@d440rc67 ай бұрын
I actually think adding a spacer on the Fimonda or any portal transmission to raise the left side should work fine, then you can have the overdrive in the axles and good to go
@PMGaming1018 ай бұрын
printing with tpu ?
@keldonator2 ай бұрын
Yes...
@syarif_rc_channel9 ай бұрын
where is the turbo boost?
@chalinp48869 ай бұрын
Did you print these do they it fit the pro line super swamper xl 2.2 how wide are they
@keldonator9 ай бұрын
Have you made any 1in inserts? I'd imagine you'd want them much softer
@LyrickCZE9 ай бұрын
Hello @D440 RC, will this be correct version for Hyrax Predators? Im currently using the set with default wheels and foam and would like to switch to these. Thank you!
@Josh-fi9sc9 ай бұрын
Pinion mesh sounds way too tight
@luisfj99 ай бұрын
How do spur gear hold up to this OVERTURE Nylon Filament?
@HarryHikes9 ай бұрын
I have printed your foams for my scx6 using green overture tpu and they are so stiff I can’t even use them. And my scx6 is running vitavon portals and brass so it is far from light weight.. I had really high hopes for these. Can you release a file that has a lot less support? Thanks.
@hungryhungryhummer10 ай бұрын
I bought a spool and this was not my experience. It was very brittle brand new out of box.
@chuck250111 ай бұрын
3:28 the PETG didn't break, you slipped, it sprung up and snapped on the rebound.
hi, fab design. what printer are you using to print these?
@d440rc66 ай бұрын
Ender 3 v2 with direct drive
@northernlightsrc8994 Жыл бұрын
Are the ruptures directional?
@DTW-bx2vy8 ай бұрын
No, it does not matter which way you mount them because the tread pattern will still be the same direction.
@smokin2054 Жыл бұрын
Do you have a parts list or a build guide,can't seem to find any info on this build,what motor,links,tranny etc...
@smokin2054 Жыл бұрын
Do you have a parts list?Or a build guide for the entire rig?Can't find a build guide anywhere.
@d440rc6 Жыл бұрын
you can find the 3d models in Myminifactory.com
@smokin2054 Жыл бұрын
@@d440rc6 Ya there is no good build guide for this crawler need a build video of complete setup.
@renatomartindelcampo3431 Жыл бұрын
Did you print them or did you have someone print it for you?
@d440rc6 Жыл бұрын
printed them
@jacobpettitrcguy1390 Жыл бұрын
Sweet what servos you using??
@marcellodipi Жыл бұрын
hi. what's the width at the inner and outer ring?
@2XRC Жыл бұрын
Absolutely amazing!! Great job!!
@drowildcat2960 Жыл бұрын
Are you the guy on eBay (Poptarts Prints) is the name that's selling your printed antifoams from your files ??
@ineedamedicpl Жыл бұрын
Hello. Will they fit original traxxas canyon trail tires?
@ripmax333 Жыл бұрын
I’m really tempted to print one, but If I do I think I will buy axles, gearbox and other stuff from Ailexpress. The original Axial parts would cost too much for me. Did you bend the axle links yourself or you bought them ready made?
@sharifbuzz2805 Жыл бұрын
awesome prints as always, kindly add raptures foams to your shop pls
@jovlanntorocarcher8026 Жыл бұрын
Wich foam would you recommend for 2.2 pitbull XOR?
@d440rc6 Жыл бұрын
here ya go cults3d.com/en/3d-model/various/2-2-tire-insert-foam-for-comp-crawling
@trailcrawler2038 Жыл бұрын
Do you print the 2 inserts separately and then glue them together?