In what tab is the oil quality sensor? I wanna reset it after changing the oil for a 2010 S40

Unfortunately this cannot be done 20- 35 .

Is it possible to transfer a 2002 key and fob to the 2003 keyfob?

Links for upgrade parts?

very educative.Thank you . regards

Hey dog hey Doug my name is Tommy I like to know if you got a carburetor for that same model boat that you got there if you do contact me I would love to buy it off of you

Thanks!!

Everything connected. Key in position 2. "Communication tool" under my "Vehicle Profile" tab shows "Not selected." Seems like Vida does not see my DICE. DICE shows Firmware Status with blinking green light (Normal Operation), USB com status not lit, Bluetooth com status lit blue, vehicle interface status static green (DICE test unit connected). Any ideas?

What size is the hole in the middle of the steering wheel?

Where did you get the tool to press out ? Or did you build ? I need one asap dealer wants 1700$

My Grandfather had a 1981 80hp Thunderbolt so I have a soft place in my heart for old mercs.

Do I really need a demo of a well running 9.8 110 merc motor? Mine runs at this time only on 1pot. So how do I test for fire on the other cylinder?

Thank you. Where is the driver's side engine mount located?

Easy easy but you do have to start with the later larger displacement 20 hp in order to get, inter alia, the larger flower-shaped leaf valves. Happy conversion to all !

Did you also have to get XC90 handbrake pads? Or is that the same size of the XC70 since you did not list that in the pars lits and i guess the hub size is the same on the rotors just that the brake face is bigger

If anyone's still looking for a fix, I found, in my case, the extra play was where the rectangular metal lug sets in the bottom gear. I cut metal shims from a soup can lid and tucked them between both sides of the plastic gear and the metal lug. It took out some of the play, but the top gear on the horizontal shaft needed a shim too. I used a piece of thin wire long enough to wrap around the drive handle shaft and hammered it to the necessary thickness to take out the play. Remeshing the gears takes some attention. I think I got it right on the 3rd try.

Okay so my engine is a 2 HP which only has one coil so if I'm correct I only need to get one cable installed under the flywheel ?That's the one for the magneto I assume ?and then one other to ground

Hello, what is the maximum speed of this engine? Regards

You obviously don’t know what you’re doing, the 35 block is completely different than a 20! Absolutely erroneous information!

3 yrs later and i'm ready to install a new pressure line, awd makes it difficult. i installed a mid rise lift 3 months ago to help working on the volvo but i can't even see the rack. This will be fun.

Any video of it running on a boat and did you notice the speed increase and did you put a 10x15p prop on it?

So I am new to vida dice but not new to working on cars. I can see misfires but don't know if it will help me isolate the problem?

Getting the bracket holes to align with the one on the mount and the three on the engine, so all four bolts could be easily started, seemed easy. What if they don't line up so well?

Would this work for a 2003 Johnson 25 electric start

I am working on an '03 S80 which is squealing like a pig in hell when idling. do you think this is it?

What type of rubber hose do you need for this?

What is the difference between a 30hp vs 35hp carburettor?

You are a true man of genius. Your pronouns are he and him. Very nice work using what you have and buying only what you need. You deserve a lift. And so do I.

Ive been running this motor with just gas im such an idiot. thank god i found this video before i did some damage..... 50:1 i see in one of your comments. THANK YOU-

Добрый день. Отличная работа! У меня такой же мотор, только с ручным стартером. Хотел поменять на электрический, но в нас в России запчастей почти нет на него

Step one can only be done if you can open the tailgate, if you can't, then forget step 1 2 3 and all the other steps until you get the door opened. On the 2009 I had to cut a square hole on the inside of the tailgate to expose the lock and then poke, push, prod everything inside the lock to try and open it. Suffice to say, I was successful after several hours, several attempts and then it was a total fluke, by accident, it opened and I have no clue what I did or what I poked to open it. I had to remove the inside tailgate cover, (what was left of it), replace it as well as the tail gate lock after I removed the tailgate license plate and exposed the lock from the outside. Yes, you guessed it, had to cut another square hole with my angle grinder and cut off disk. Close to 2000 for replacement parts, shipping and tax. So grand to own a volvo you can't manually open.

What gets me about all this is who is stupid enough to get thrown from a boat.Got just as much chance of being hit by lightning.How much damage can a 6hp motor do?

I have a 102cc meant for a sail boat manual says 4 hp is there any way to get more out of the 102cc 2 stroke

I have the same engine and had it overheat on me today due to a plugged line within the water pump system so I'm looking to do this. How has this been holding up for you? I wonder why this wasn't done from the factory?

hello how did you know that was the one? Any particular noise ? thank you very much

Have a part number for the switch or a link? Thanks.

My ‘82 110 thunderbolt on a 12ft v-hull Klamath will do 34kph, no idea what that is in nots but its got plenty of power for a 9.8

Sadly, LeroysRamblings website is gone :(

Where do I get the actual dice driver for windows

Really smart ``auxiliary bolts'' for tire fitting. The tire rattles a bit and especially when tired and cold it feels like the devil!

This is a great video! I have exactly those rollers, and that exact issue. Where does one buy the bearings?

You have saved me a lot of trouble

Thank you. Your video helped me open my 2007 Volvo V70 from the inside. Bravo!

Thunderbolt 110 are closer to 12 horsepower. In 1984 the regulations changed for Dyno testing outboard motors, because some of the manufacturers were under-rating their engines to beat the competition

Thanks for explaining car symptoms and diagnosis testing. Btw I’m scared to death of turning that petcock and braking it. Always remove the hose

Qual a utilidade deste botão na lateral?

brass nut that fell off there was meant to be a plastic retainer on shaft that nut pulls down on to lol

Heat the side you're cutting with a heat gun or hair dryer, the glue will let go. Just clean off the excess glue and it will reassemble like new.

I have done this job before on my v70. A little tip is to put Vaseline on all the clips on the surround, it makes it easier to get it off next time without breaking them.

Very enjoy