My 92 Tahoe idle gets higher when I use a jumper but the compressor doesn’t kick on, any ideas?
@JCTFIXIT5 сағат бұрын
Sounds like you need a new compressor
@CLANE_TV13 сағат бұрын
Can i do this for my hyundai accebt 2020? Stock head unit
@airborneranger-retКүн бұрын
Liked and subbed
@JCTFIXIT21 сағат бұрын
Awesome thanks!
@dsmith28582 күн бұрын
Can you run everything to include Furnace and AC?
@JCTFIXIT2 күн бұрын
Yes. But it all depends on how efficient your equipment is and what kind of power it draws. everybody is a little bit different.
@pankajmistry46002 күн бұрын
Thanks. Just bought one for outdoor cooking and such. Thanks for the review. Never had a gas powered generator before!!! Good review bud😊
@JCTFIXIT2 күн бұрын
Sweet! It's a solid unit. Still running great!
@blackguy-ij7ij6 күн бұрын
I've had several ships swear that this was impossible and I needed to buy an aftermarket head unit in order to get aftermarket subs. I knew it was bullshit
@riverrivers25011 күн бұрын
Only one regular outlet?
@JCTFIXIT11 күн бұрын
Yep. One regular and one RV. Stuff like this exists.... amzn.to/4bLkHHN
@milwaukeebiker11 күн бұрын
Looking for a straight answer on what the KEY ON ENGINE OFF (not running) Fuel Pressure Sensor reading is supposed to be (on a real scan tool) for and LBZ and LMM when the sensor is working correctly. Is it Zero (0.0 Psi)? Or is it supposed to read something?
@JCTFIXIT11 күн бұрын
IDK
@milwaukeebiker7 күн бұрын
@@JCTFIXIT What did it say that I'm looking for? I've been a diesel and auto tech for over 40 years and own a truck dealership. Why are you assuming anything? If you don't have the answer then don't comment. Simple as that. I own 3 LBZ duramax single cabs myself and have all the scan tools I need to have with me right now while I'm out roaming the country in my 5th wheel with another enclosed trailer behind that. Over 14,000 lbs behind me back and forth over the Rocky's. All brand new Bosch fuel system within the last 8,000 miles on this one. I was trying to go through everything after getting fuel in WY after I still had 1/2 tank and it turned out the the fuel was so bad there that it sank the whole tank. I was testing everything why it wouldn't make it up the next mountian pass after leaving with the tank filled up. I ended up finding that everything was perfect on it, except the fuel. I bought a clear 12 foot section of 1/2" hose from Ace hardware and pumped it to someone for free into their reserve tank. Filled it back up at a better truck stop and was all back to normal again. The best rule of thumb is like I said... If you don't have the answer that someone is asking for, then don't comment.
@JCTFIXIT7 күн бұрын
Fixed it for you.
@delaliayensu647612 күн бұрын
My laundry machine door won’t close. What do I do?
@JCTFIXIT12 күн бұрын
For real?
@delaliayensu647611 күн бұрын
@@JCTFIXIT uea
@delaliayensu647611 күн бұрын
@@JCTFIXIT yea
@delaliayensu647611 күн бұрын
@@JCTFIXIT it’s the same one from the video that you posted 4 years ago
@JCTFIXIT11 күн бұрын
Is your locking mechanism broken and actuator on? Does everything line up? Come on people use some.basic troubleshooting skills.
@davidacosta806017 күн бұрын
Thank you great video . What is the model number of that stove? I Have the same one but no model number info.on it. If you can please provide.
@JCTFIXIT17 күн бұрын
I don't have it handy, but these ignitor are the same across a ton of models, so if it looks just like mine in the video it should be good.
@davidacosta806017 күн бұрын
Thank you for the quick reply. I meant the stove model number
@JCTFIXIT17 күн бұрын
I don't have the model number available. It is a relatives.
@robsedia723420 күн бұрын
Can't thank you enough for this! Because of your video, I was able to fix my LG Oven in 5 minutes and for under $30. Thank you!
@JCTFIXIT20 күн бұрын
Thanks for letting me know. That's great!
@isaacvelasquez7723 күн бұрын
What is that connector on the ac line? 1:24 I have a loose connector not connected to anything
@JCTFIXIT22 күн бұрын
Low pressure cutoff
@ItzMarcoz29 күн бұрын
does it have a be a 20a add-a-fuse or can it be 10a?
@JCTFIXIT29 күн бұрын
Ideally you would match the fuse that's already there and then the actual add a fuse circuit can be way less.
@ItzMarcoz29 күн бұрын
@@JCTFIXIT does it have to be the ignition fuse or can it be another?
@JCTFIXIT29 күн бұрын
It needs to be a slot that is only on when the car is on or you will drain your battery.
@ItzMarcoz28 күн бұрын
@@JCTFIXITmy local auto parts stores only sell up to 10 amps. is there another fuse i can tap into that’s not the ignition
@noahkottmyer909929 күн бұрын
What if my ign switch is a 2 amp fuse? Im sorry if this is a stupid question. Im really new to electrical and im just throwing myself into this job?
@noahkottmyer909929 күн бұрын
I just looked and my cigarette lighter is a 20 amp would that work?
@JCTFIXIT29 күн бұрын
The add a circuit has its own fuse. It doesn't need much as it's just the signal to tell the amp to turn on.
@JCTFIXIT29 күн бұрын
You want to go off something that is powered only when your car is on. Otherwise your amp will stay on all the time and drain your battery.
@roncogan9604Ай бұрын
My broiler works but oven (bake) doesn’t and gives error F-09. What is the issue in this case ?
@JCTFIXITАй бұрын
Did you watch the video?
@roncogan9604Ай бұрын
@@JCTFIXIT yes, here is the problem: I ca “force” my bake function to work if I turn on the top gas burners, but I get F-09 if I try the bake function without the top burners. Can this be circuit board issue as well ?
@JCTFIXITАй бұрын
Sounds like you need to replace your ignitor.
@roncogan9604Ай бұрын
@@JCTFIXIT ok thanks for the help. Much appreciated. I will try the igniter first and if that doesn’t work I will replace the circuit board.
@Snceday1Ай бұрын
Big 3 upgrade is definitely needed and 2 gage or even 0
@JCTFIXITАй бұрын
Big 3 upgrade?
@Snceday1Ай бұрын
@@JCTFIXIT KZfaq it.. you add a large o gage or big wire from your alternator to your positive on battery. Then you run a negative from your battery to the frame of vehicle and then you run a cable from engine block to frame of vehicle and by doing that you updated your vehicles electrical system which at that point you can have great safe power for running a audio system including subwoofers and amp... Because it's takes a lot of amps and it could kill your battery.
@johnjones-zq2ufАй бұрын
No gasket
@JCTFIXITАй бұрын
Yes. That's is correct. I award you 10 points.
@johne6716Ай бұрын
Great vid man, hope the baby is Okay?.
@JCTFIXITАй бұрын
She was fine just upset that mommy wasn't around.
@DannyGarrettАй бұрын
Thanks I’ve been trying to figure this out so simple to fix.
@ClaraSilva-el3yrАй бұрын
I have a factory sub in my trunk as well. I just tap the speaker wires between the amp and the factory sub? I would love to not have to open my dash. On my amps manual it says to connect speaker outputs from receiver to high level input connector of amplifier. I could go into my dash and do that?
@JCTFIXITАй бұрын
You could.....
@izh6421Ай бұрын
Thanks for the video, I just installed a 75 inch tv with this mount and I noticed I can turn it left or right to make it level almost as if something was loose, do you know how I can tighten it so it stays level all the time?
@JCTFIXITАй бұрын
There are nuts that need to be tightened to ensure this. I would recommend some medium strength threadlocker on this nuts. When you get a big tv and you move it, it kinda acts as a lever on the pilot point making it harder to lock the pivot point down since very little force from the edge of your TV equals a lot of force at the central pivot.
@simonmears1726Ай бұрын
Don't really need rtv on tranny should have gasket can use dab of rtv on corner s just too keep gasket from moving did my corolla no leaks 😂
@nolan3184Ай бұрын
How did you find out which wire was negative and positive for the stock subwoofer in the trunk to connect the amp
@JCTFIXITАй бұрын
Lookup your vehicles stock speaker wiring diagram.
@nolan3184Ай бұрын
@@JCTFIXITI’ve looked everywhere and couldn’t find it so should I get a wire negative and positive tester?
@JCTFIXITАй бұрын
You could What colors are the wires?
@nolan3184Ай бұрын
@@JCTFIXIT the left side of the stock subwoofer has a black wire and a green with red stripes wire. On the right side of the subwoofer there is a yellow wire with red stripes and a red wire with blue stripes.
@JCTFIXITАй бұрын
Year make & model?
@derickd2385Ай бұрын
The key is hand tighten the screw until see the bead squish out just a teeny, after 1 hour then torque the screw.
@rackyshakАй бұрын
Yooo, thank you! Helping my parents troubleshoot theirs and this seems to be the issue.
@ashleyhobby10702 ай бұрын
Looks like spaghetti
@JCTFIXIT2 ай бұрын
I love italian food
@zachdent9112Ай бұрын
😊
@baileegatton77672 ай бұрын
Will my system work with rca to the rca converter to the rear left speakers wires? And what wire do you use to run the add a circuit? Speaker?
@JCTFIXITАй бұрын
Your wording is a little confusing. Without knowing your setup, it's hard to say. Generally though on an amp, the rca inputs are for signals that are low and not being driven already. High level inputs are called such because they can handle a higher watt load incoming into the amp.
@skmmiranda12 ай бұрын
Caution taking out the circular trap to the right of the drain hose can release A LOT OF WATER!!!
@JCTFIXIT2 ай бұрын
That's why you drain it first silly
@govolsfightvolsfight29082 ай бұрын
Good high quality is subjective in this case. Please tidy it us, it's making my ocd act up.
@JCTFIXIT2 ай бұрын
Haha. I feel you.
@jeep1987Ай бұрын
No one cares about your ocd
@KevinPratt-sg4yd2 ай бұрын
Will this two battery setup provide enough power to run a fifth wheel?
@JCTFIXIT2 ай бұрын
If it is based on 12V battery architecture then yes
@TalkingHands3082 ай бұрын
I already replaced the front door speakers. Kind of torn if I should replace the tweeters first or the rear speakers... Which makes a bigger difference in your opinion?
@JCTFIXIT2 ай бұрын
Rear speakers IMO
@TalkingHands3082 ай бұрын
@@JCTFIXIT Ok, thanks!
@MOBU762 ай бұрын
What if the screw is not there?
@JCTFIXIT2 ай бұрын
Then it is a different model or is missing the screw.
@CodyPexton12 ай бұрын
Thank you!!!! Such a big help man. And good video. To the point yet thorough explanation. Thanks again!
@JCTFIXIT2 ай бұрын
Glad it helped you!
@JimmyLima7152 ай бұрын
Pretty sure all powered subwoofers automatically turn on and off when tied into the high level inputs to just one rear speaker needed. Why all these other devices and remote wires needed?
@JCTFIXIT2 ай бұрын
Some newer models do that. Many do not. Also you want both so that you get tunes from L & R channels
@ourv96032 ай бұрын
I found my 6" GARMIN GPS fits PERFECTLY into the sunglass holder. I just need to tap that purp wire for key on power. !
@ourv96032 ай бұрын
What that sticky stuff is is, FRICTION TAPE. 100 years ago when man first discovered electricity friction tape was developed to act as an electrical tape. Unlike the PVC electrical tape of today, friction tape has no adhesive it is just a little sticky to stick to itself. This is what our great great grandads used. I am amazed it is still around but I guess for whatever reason, Ford finds it necessary to use it here & there. !
@lesliegarneau2 ай бұрын
Connector would not have a “shirt” in it. It would be an “open”.
@simonmears17262 ай бұрын
Nice and clean both surfaces with razor nice bead around bolt holes mate together and nip up then tighten stop using gaskets on alloy sump s bit of a pain 😢
@stanlee220020 күн бұрын
Your message is nonsensical
@wlightman2 ай бұрын
I thank you very much for taking your time to make this video, it helped tremendously, I couldn’t have done it without this video
@JCTFIXIT2 ай бұрын
Thanks for taking the time to let me know. It makes me happy to help others!
@andyhernandez91542 ай бұрын
Wats that extra cable ?
@andyhernandez91542 ай бұрын
Or plug I should say
@JCTFIXIT2 ай бұрын
The little red jumper?
@brandonconners66062 ай бұрын
Amazing...had the code today, had no idea what it meant...stumbled onto your clip and it was a easy fix. Clogged pump! Very much appreciated, thank YOU
@JCTFIXIT2 ай бұрын
I am so glad it helped you out!
@ashtonharvey57232 ай бұрын
If your car has a factory amp wouldn’t that be playing low end from your cars amp into the amp your adding? Someone told me I shouldn’t do this but I don’t see really why not when I’ve seen others do stuff like this. My car has a factory amp that uses the rear 6x9’s for bass. Would it be ok if I do this on my car like you did yours? I’m guessing your car has a factory amp which means you tapped into the low end speaker in your car to give your amp an input from your factory stereo.
@JCTFIXIT2 ай бұрын
People recommend not doing this because your amp can prefilter the frequencies for your stock sub that may or may not allow your new aftermarket sub to reproduce to its full capability.
@jaskarandhaliwal83 ай бұрын
Where to hook the power wire if you don't have under the hood battery? Should I hook it to jump start connecter?
@JCTFIXIT3 ай бұрын
If your battery is located somewhere else like trunk or under rear seat, just run it from there.
@Maddanju16323 ай бұрын
Excellent tutorial and expertly explained. You were lucky that a speaker in the boot was accessible as mine are in the rear doors…
@JCTFIXIT3 ай бұрын
Agreed. Good luck with your install!
@plus25793 ай бұрын
dude this video was exactly what i needed.
@JCTFIXIT3 ай бұрын
Love to hear that!
@seyuueueerenityahhhh3 ай бұрын
So what if your vehicle is originally 24v
@JCTFIXIT3 ай бұрын
Find a battery that suits you. 20v max from some applications should work.
@gtrance35673 ай бұрын
I’m thinking about adding a powered subwoofer to my car trunk. I take it i’d follow similar steps you did? Also, it looks like you tapped twice into your speaker? Is that right?
@JCTFIXIT3 ай бұрын
Yeah just to grab left and right channels you could also use rear speakers if you don't have a sub stock
@gtrance35673 ай бұрын
@@JCTFIXIT thank you!
@natevalverde22213 ай бұрын
Do the t taps allow the rear speaks to continue to play. I tapped in directly and now they don’t work is that why?
@JCTFIXIT3 ай бұрын
You need to leave the lines running to rear speakers in place and tap into them to piggyback the signal.
@BarbaraBelcher-tn7cy3 ай бұрын
thanks for the video Iam going to try this I will let you know if this is my problem thank you again.