On my Marathon the reset button is not popped out.

Very informative. Found capacitors locally, installed, and works great. But now, the adjustment for volume and brightness is not working. No matter how I try to set it there's no change. Any ideas?

what if you don't see the cable for the leg release ?

So helpful, many thanks for posting this video!

Great video. I have a 2017 Sienna with this problem. Didn't think it would be this easy to take care of it. You're a genius, MrPeller80!

Sounds like a element is shorted .. what the hell is a cow rod doing in a water heater ?

Excellent video with a simple fix. My daughter had the same problem with her Sienna. She brought the car in for routine service with a local shop and asked them to look at it. She got a call saying it would cost over $320 including labor and the part from Toyota. I used your Amazon link and replaced it myself in 15 minutes for $28. Thanks.

Hi, this worked but now getting error code e-01. May the the thermister. $17.00 plugs to control panel. Is it hard to replace?

Bosch is setteling a class action lawsuit for the units listed below. google search it yourself for a link. You can receive up to 400$ for these units having defective displays HBL5751UC HBL8751UC HBLP751UC HMC87151UC HMC80251UC HMC80151UC

Good sh### thanks pal

I removed the brake 5 years ago and no problems ever since 👀🤷🏼

Great video, replaced both caps and it worked. My daughter now has it back working after almost a year!!

Only 4 screws (10mm hex / phillips screw) to loosen the lower splash shields and get easily at both sides without reaching down from above around the battery or coolant reservoir...

Informative but not well enough

Hi what was the socket number you used? 10mm?

Thanks for your video helped me fix my microwave! I have the same microwave and oven as you. My oven display started actung up. The first number not visable unless i tsp the screen. Would this fix also work on the oven?

You are amazing! Thank you for this video. I finally got around to doing this after having a blank display for 8 years! Worked like a charm!!! $2 fix with probably $8 shipping (CDN$) from DigiKey was a tiny fraction of the cost of a service call who probably would've just replaced the whole board.

Great video. Replaced mine today and your video was very helpful.

I just try this after watching your video and just wanted to say "it worked". Thank you for making this video and sharing with others that have problems like this. You save me a lot of money by not taking it to the dealership. Thank you Thank you!!!!

“You can see that I just dropped the screw…the exact thing I told you not to do” 😂

I just encountered this issue with my 2006 Sequoia that hasn’t been driven regularly in 9 months just sitting in the driveway and just found this video. I’m gonna try this tomorrow and see if this works. Thank you.

Did your microwave ever have mon responsive buttons from being stuck in a sleep state? I to randomly mash a bunch of buttons to snap it out of it

Thank you so much!

Thank you bro this video help me a lot and save me time

Thank you so much for posting this. My microwave has the exact same problem for years. Could barely see the screen at night, and not at all during the day. Was reluctant to spend the $350-$500 people were quoting me. Bought the soldering iron for $30 at Home Depot, and the exact capacitors you linked to. First time soldering. Fixed it in about an hour. Felt like a total hero. One of the surprising effects was that the volume now remains low. Even after changing the settings in the microwave, there is no difference between LOW and HIGH volume. I suppose the microwave Giveth and Taketh! Really appreciate the detailed step by step instruction. You're awesome!

I have a 80151, notice the clock display is ok, but when I tried to select the sensor reheat or other functions the display is dim can’t see with kitchen lights on, can only see little with no lights. Is this the same cause from those 2 capacitors?

I have the same model microwave and have had a dim display for years. Now the microwave is dead. No power to display. All my fuses are good. Pulled the circuit board, and have the same burnt discolouration. Think this could cause my fault? - no function? Either way it’s worth the attempt to fix. Thanks for the video.

Great info but I wish you would have pulled the panel off to show us

I went on a trip. And the next time i used my 01 sequoia the defroster wiper and couldn’t roll it down. Also my door sensors are glitching. Gonna try this to see if that’s the case. Thank you for the video

this is a shitty video to be called "replacement fix"

Man this just saved me tons of time trouble shooting. I was only like 30 seconds into the video and already got my answer. Didn’t know there was a ecu reset function. That did the trick for me. Thank you so much sir!

Thank you for posting this! It really helped! I was able to replace the rear motor on my 2013 Odyssey today. I had to use a puller, Lisle 54150 which was on sale at my local Carquest for $29 CAD, to get the rear arm off. I also recommend getting the Honda factory motor as it comes with new mounting bolts (and I got a new "special nut" that goes underneath the arm and holds the motor to the window) and it was significantly cheaper than an aftermarket motor at $110 CAD from the dealer!!! Thanks again 😊

It's worked...tnx

What can you do when you have a leaking tank, and the company sends a letter to take to any dealer then get rejected by the dealer.

Thank you so much! I have an older Toyota Sequoia 2005. I love this car! I was dreading thinking that I had to take it to the Toyota dealer, which they would have easily charged alot of money for this easy fix! Thankful from a Southsider of Chicago.

Do you have an update? Have you tried removing it after some time? In theory it seems like it would work, but I can also imagine the paper towel or anything you stick inbetween could also fuse itself into the drywall and bracket.

Thanks so much!

Spent $1500 on my new ariens and the valve also sheared off ar the rivets the first time I ran it… I shouldnt have let lowes pre assemble it is my guess… or ariens should not use cast bolts there…

after saw your video, do Exactly what you said, pulled the rear window switch for 10 second, fixed my not working rear window wiper and defroster ，thank you !

Did this hold up or did you have to replace the motor? Also, mine stopped working along with everything mentioned but my wiper had random on when turning key off and randomly it worked on command but would never reseat itself.

Outstanding video! It really helped me fix my display. The replacement part numbers and suggestions were perfect. Thanks for sharing this fix.

I have the same issue, what I don’t understand is if the window issue would be the window motor, why won’t the rear defroster or wiper not work? Thanks, hope you see this!

Ours sticks but doesn’t make that horrendous sound.

Man. Spot on. Fixed my 05 Sequoia doing exactly what you said. I had every same issue.

They’re called elements. Your unit shouldn’t need reset, one of your thermostats or elements has an issue. Make sure the thermostats are set at the same temperature It’s not 220 it’s 240v I’m a licensed plumbing contractor with 27yrs of experience. It’s not a gfci, please stop saying “cow rods”- please use upper and lower elements to sound like you may know something. Please don’t form your own hypotheses if you haven’t been to plumbing school about how your lifetime warrantied Marathon works or what trips the thermostats; you’ll void the warranty. UNDER NO CIRCUMSTANCE DO YOU EVER WORK ON A LIVE ELECTRIFIED WATER HEATER!!! Shut it off at the breaker. Best wishes, good luck

I bought this on amazon and it didn't work. Even with the tiniest pull, the glue and piece just came right off the stainless steel. Tried it several times

great video

Hope you see this even though this is an older video! I have a 2005 sequoia sr5 2wd I live in so cal. And we had a “hurricane” last week was working on replacing my rear latch actuator bc the rear latch would open and totally forgot to put the weather stripping back in that fall during that project. Everything in my rear latch area got wed All the electrical components Motor, small box that has the ecu for the door Am I doomed and need to replace the motor and other electrical components Window won’t roll down Key won’t unlock or lock the back latch Sorry for the long comment !

Thanks for this tip!

Thank you!