Always best to go ahead and clean up the street drain as well. Weeds there will make your yard look bad

Thanks very much for the video!

Can't wait to see you other video on chevy rust spot when you fix it

Mark what is the bore size for the 5.5 inch pulley. Did you get at tractor Supply also?

And by the way them things can cut up to 2 in depth

If it's within the 90 days I would bring it back and exchange it for a different one it sounds like it has a defect in it right out of the box that one that you got

thanks for that. fixing to go out and do it.

Thank you for the video sir 👍😎🇺🇸

Ugh ANOTHER Road Glide…. I am so glad I have a unique motorcycle that there aren’t many of all Over the roads… a Street Glide (Bwaa haaa yes I’m joking)

Thank you for the video sir 👍😎🇺🇸

Looks good. Hope you guys r doing good

I can't wait to see the other rust repair show us when you do it

Nice like when you show us stuff

Nice blend job, Good spray passes, Do yourself a favor and get under and look on the backside... open the rubber plugs and you really should spray a rust prevent coating inside those rockers, you are luck the rust isn't through yet.... it usually starts from the back inside and works outwards. I know you know your stuff.... just wanted to remind you. I have seen so many bad rockers and replaced so many

Never received a comment back.I like the 2 stroke makita weed wackers.They were a lot better

Wasnt a very good video nothing explained. I dont think theres any comparison to chrome your forks will need done again due to oxidation.

All that work and time ill send mine to get chromed and itll be done instead of all that fiddle farten around. Chrome looks better than polished

i did mine a few years back must have reversed the wires on the brushis. it ran backwards.did not realize ittill i got to the lake. short trip.

great repair 🖖👍

Love the Gator blades on these mowers.

Thank you for the video!

It's fixed but what was the root cause of the failure?

Sure is nice to see some green grass! We are really dry in Virginia!

Great job guys and thank you for the video 👍😎🇺🇸

I would like to get one of these for my Gravely ZT HD, but was wondering how difficult it is to remove this in the fall when I want to install my bagger system?

hello, great video, from Leesburg Virginia

Ok, That’s why you guys cover every inch of your skin, you’re afraid to get dirty. 😂 Enjoy the heat! That’s nuts. I’d be doing it naked if it were legal. Once you master the job you will see that you don’t have to work hard or get excessively dirty doing lawns. All the best!

This same video is on another channel called Mark's Work Shop. They appear to be stealing your content.

Nice work and good to see you guys mowing again. Thank you for the video 👍😎🇺🇸

Nice job!!! Love to do fields like that. Night and day difference when done!!!

Appreciate the video (watched the whole thing), but think I'd just get a little trailer.

You could set up the rear truss as a a hinge and thread your pull line around a pulley on it so once the canoue came forward and hit an end stop, it would raise the tail of the canoe so the canoe wnds up parallel to the truck bed and you won't have the front of the canoe sticking up so far in the air where it could hit low branches or bridges or anything.

Great knowledge and how to video on the hydro fluid but I will add that motor oil and hydronic oil are not supposed to be swapped. They have different chemical properties and can cause damage

I have a 2024 cheetah 2 any recommendations to make that seat softer

Nice day for fishing and thank you for the video sir 👍😎🇺🇸

This is my new favorite youtube video. Btw, what year was the garage door installed?

Thank You son!

Mark, what was the final outcome on the 5-1/2" pulley. Solve the clogging problem, cause any bearing failures?

Where did the 12oz per fork come from? My FSM says 6oz (5.2oz at oil change) per fork.

Great video, thanks!

😎💪

I dread doing the smaller front tires its always a NITE MARE for me!😫

Thank you for the video sir 👍😎🇺🇸

Very hard work and nice couple

Are you just walking around to random properties cutting up trees or are these jobs your were hired to do?

Great video thanks! Sorry about your camera

I tested a prototype 2024 BR900C it’s max is 302mph and I almost flipped my geo metro over with it

Great set up. I’m perusing something similar . Does your zero turn handle the weight towing, the front weights on mower and the second blower?

Very nice Ms Vickie and thank you for the video 👍😎🇺🇸

I’m afraid to take my carbs off on account of perhaps cracking the boots. My bike is at 1984 Nighthawk 750 S. Parts are scarce.