Krankie V

Пікірлер

@rickroel4994 8 күн бұрын

Would this work on a rear Subaru bearing?

@Krankie_V 8 күн бұрын

@rickroel4994 I have used it several times for that. The matco salesman claims that every tech in the local subaru dealership bought one.

@Violetaacosta1959 10 күн бұрын

Who is watching this in 2024

@psychodelicrock12 13 күн бұрын

Keep on revving

@elmayimbe_the_amateur_mechanic 17 күн бұрын

1000lb-ft cordless impact should work with this right?

@Krankie_V 17 күн бұрын

@elmayimbe_the_amateur_mechanic it works, but be careful because if you just go to town on it, it's possible to cause damage. Normally I just use a ratchet so I can feel what's going on

@elmayimbe_the_amateur_mechanic 17 күн бұрын

@@Krankie_V , thanks. I have 2 of the same cars. A 2002 and 2005 Infiniti Q45. Here in San Diego so no rust. The 2005 needs a ton of work and has sat for a year. I have had all 4 hubs and both LCA's for over a year now. Gonna experiment on the 2005 with this. If it goes well I will just leave the old hubs on and put the new ones on my 2002. Thanks.

@Krankie_V 17 күн бұрын

@@elmayimbe_the_amateur_mechanic with no rust, you probably don't even need this tool

@elmayimbe_the_amateur_mechanic 17 күн бұрын

@@Krankie_V, I did rusty front hubs on a 2013 Ford Explorer from Virginia. Scared mr for life. I am using this thing for sure. I want this to be as easy as possible.

@trondfiskeseth2559 26 күн бұрын

tip: use a steel plate on the caliper attachment to distribute the pressure from the tool

@murrayferrino7064 29 күн бұрын

i am working on a troy built w/a briggs and stratton 650 series which i think has this very problem. thankyou for this awesome imformation!

@Krankie_V 28 күн бұрын

Hope it helps

@DaDaDo661 29 күн бұрын

Are you in the rust belt?

@Krankie_V 29 күн бұрын

Big time. Upstate NY

@user-xz8hq7ye2x Ай бұрын

I ised to work on the ol' Bunton 32's Back then Honda made a tough motor, I the only problem with the Buntons was the deck. Made from cheap canadian steel. If the paint chipped and moister got in rust-o-roma happened over night. But that motor was a beast

@Krankie_V Ай бұрын

It does appear to be extremely well built. The deck on this one has plenty of chipped paint, but it isn't very rusty. The steel is inelcredibly thick for a mower!

@neviestix Ай бұрын

So helpful. My automatic start and keep going button burned out a long time ago. Now i need some kind of oomph routine. The manual heavy crank start. A choke pulled just the right amount. Gas pedal perfect. Dont rev straight away. Let the engine idle and warm up first. Old Model T

@nazigrammar9728 Ай бұрын

This tool is almost useless, at least for most of knuckles(backing plates or caliper mounts will get a damage)

@Krankie_V Ай бұрын

Not true.... I have used it many times without damage

@nazigrammar9728 Ай бұрын

@@Krankie_V I've just checked on Amazon and many people said the thread on a rod is so weak, even on an item it's described as Upgraded. Where did you get urs from?

@Krankie_V Ай бұрын

@@nazigrammar9728 I bought my own from rockauto and thr ship I work in has one that came from matco tools

@DaDaDo661 29 күн бұрын

What's worse? Ruining a cheap back plate? Or giving up and bringing the car to a shop that will charge you $500? I don't understand the backing plate argument, just cut it off, buy another one or don't put it back on

@nazigrammar9728 29 күн бұрын

@@DaDaDo661 many backing plates are not available. Many of them are crazy expensive, even older Toyota's. I work for a small used car dealership, so I know what I'm talking about

@daviddykes8247 Ай бұрын

The problem is the regulatory is bad

@user-et4mo9jk9w Ай бұрын

Oh my god that truck sounds amazing

@shaneshane6642 2 ай бұрын

Is this fire order for 1.6 cvh ford escort Xr3

@Krankie_V 2 ай бұрын

This is a 1.9 cvh, but I believe it is the same as the 1.6

@thatrabbitguys314 2 ай бұрын

Imagine the confusion if they called it oil lol

@thatrabbitguys314 2 ай бұрын

Would the brake system technically run since they are both oils?

@Krankie_V 2 ай бұрын

Brake fluid is not oil based. Oil damages the brake system.

@mouseclicksforu9724 2 ай бұрын

@@Krankie_V I thought brake fluid is a type of oil! Brake fluid, prestone is a type of oil!

@Krankie_V 2 ай бұрын

@mouseclicksforu9724 most brake fluid is Glycol based, except DOT5 which is silicone based. None are compatible with oil.

@mouseclicksforu9724 2 ай бұрын

@@Krankie_V I use dot 3 brake fluid for my 2009 ford focus! I checked on the cap!

@Krankie_V 2 ай бұрын

@mouseclicksforu9724 good, best to use what is recommended. It would be okay to use DOT 4 if you wish. It's the same type of fluid with more boil over protection. Basically a higher performance version of the same fluid.

@silverbulletcapitalllc 2 ай бұрын

What if the whole stem broke?

@Krankie_V 2 ай бұрын

Replace the entire housing

@toml.8210 2 ай бұрын

You should use DeOxit on the connector terminals to remove any corrosion. DON'T use WD-40, since it isn't electrical connector cleaner! Add some antisieze to the screws before to install them.

@Krankie_V 2 ай бұрын

Never had any corrosion issues on the socket connectors myself, but good tips! I never use WD40, that stuff isn't very useful to me

@aaronschiffert9739 2 ай бұрын

LEMMER in mississauga is the ones to deal with. I’m having the exact same issue with mine.

@Krankie_V 2 ай бұрын

I got an email back from them eventually. There is a large packing nut in the pump assembly, found under the metal nameplate cover. Loosening that slightly got mine to work better.

@garrykennedy5484 2 ай бұрын

Maybe those tubes fall off sometimes? My Blue Rhino one I just got won't keep good flow. Research has showed that the reason may be because it's overfilled?

@Krankie_V 2 ай бұрын

Not sure, I had a lot of flow when it was over full, but it was also letting liquid out instead of just gas, which made my heater expel large flames. Low flow is usually a problem with the regulator on the appliance.

@phroggie69 2 ай бұрын

Timing is low but other then that definitely not stock

@Krankie_V 2 ай бұрын

Initial is 14 degrees BTDC total time about 28 degrees

@mrreviewsitall7496 2 ай бұрын

running out of fuel😂

@yunggunnah_yt 2 ай бұрын

Something isn't hitting right. I could tell too. I'd say your correct sir 😂😂😂😂

@Krankie_V 2 ай бұрын

@@yunggunnah_yt it's just cold. Much more consistent at full operating temp

@michaelnagy4603 2 ай бұрын

Sounds great❤

@Arizonaclassics 2 ай бұрын

Sick

@user-ov2xb2wi2m 2 ай бұрын

That surpasses big, id call that a hog ass cam

@AnimeBaller22 2 ай бұрын

Hi Krankie, I a saw a comment of your about fixing a stolen kia in your shop. May I ask how much it costs/how easy is it to fix just to get the car running again? Mine wouldn't start but I don't know if that's because the electricals we unplugged or whatever they did. Thanks

@Krankie_V 2 ай бұрын

I believe it was around 2000$ but can't be certain. The billing is not my job, and it was handled by insurance anyway. That car started and ran just fine though. Just a lot of damage to the steering column

@TheDogLife5225 2 ай бұрын

Miss my old 63

@Jeromeeb 3 ай бұрын

Sounds like 💩

@thematt4104 3 ай бұрын

You need to an updated driving vid like from a few years ago

@Coronet_shop 2 ай бұрын

Agreed

@Perich29 3 ай бұрын

Very good.

@kman2783 3 ай бұрын

Sleeper! 😂

@Rickimusic 3 ай бұрын

Running the gas pedal.

@obsessedwithcars219 3 ай бұрын

Jeeze thats alot of rpm for an FE

@user-kz5th5bn3m 3 ай бұрын

Right now I have same year truck and model but with a crate 302 in it. As much as I love them rat motors my dream is to have a 390 in it. It’s powerful and sounds absolutely incredible. Great video my man

@Krankie_V 3 ай бұрын

Thanks for watching and dropping a comment. I absolutely love the FE engines.

@SuperKONR 3 ай бұрын

oh oh oH IT'S MAGIC!!! 😂

@jacobharvy 3 ай бұрын

Um..... i never knew

@WillBilly. 3 ай бұрын

@EtFoff 3 ай бұрын

This should be on the drivers test if you fail it no car drivey drivey

@matthewscruggs7104 3 ай бұрын

Most people should be on the road period. They definitely shouldn’t have access to anything under the hood. I knew a guy who’s brakes locked up on the passenger front so he cut the brake line thinking he could just drive with the other brakes. I said no you don’t have any brake fluid left for 1 and so many other reasons. Lol natural selection isn’t working correctly anymore. Hahaha

@Krankie_V 3 ай бұрын

Damn, that is crazy!

@adaycj 3 ай бұрын

I pour is backwards anytime someone is watching. That way I know what type of know it all im dealing with.

@TheMunchieGang 3 ай бұрын

Well, because it doesn't matter when you use a funnel!

@jaredallen1149 3 ай бұрын

I've been commenting for YEARS about this very thing. Common sense ain't so common anymore, is it? Schools used to teach kids how to be good grown-ups. Now they teach kids how to be gay and call the cops on their parents... SMDH.

@erickmejia4602 3 ай бұрын

I just use water

@TheBigjon1020 3 ай бұрын

Good ol ford

@907buschmin2 3 ай бұрын

I mean if they all using a pour spout then what diff does it make? I never do use a pour spout unless i need to use one. The oil i use still have the little indicator on the correct way to pour the quart

@Krankie_V 3 ай бұрын

When you see soemone pouring oil all over the outside of the engine because it's glugging from the bottle, then you see the difference it makes.

@907buschmin2 3 ай бұрын

@@Krankie_V lol yeah. I've made that mistake when I was a teen trying to change oil on an ATV 🤣

@reltub20001 3 ай бұрын

I remember this. Most people now don't know what an opener with the spout built in for opening and pouring from a can

@Krankie_V 3 ай бұрын

That was before my time but I do know what those look like and how they were used

@reltub20001 3 ай бұрын

@@Krankie_V that is good. I used them for a few years. My dad had one and the service station I started at had several. We also had full service at that station

@stevechaney2958 3 ай бұрын

Very professional job inventive creative and easy to do hahaha

@baitmaster8706 3 ай бұрын

Unless you're hitting jumps on salted roads for 5 straight winters, that strut will not fall out with only 2 studs. You uploading this tells us that his panel bond job held up for the life of the shock. Seems fine to me. However I would have rather swapped it with an old stud rather than letting the next guy know I've got that hellcat mindset😂

@Krankie_V 3 ай бұрын

You say "The panel bond job held up for the life of the strut" as if it actually repaired something. It may be true that nothing really happened as a result of this, but making an effort to hide it instead of fixing it is disgusting.

@mikehorb9485 3 ай бұрын

I’m going to pretend I never saw this short and I’m moving on. Y’all know why, wish me luck. Sometimes you have to do what you have to do, but this is too ironic so I’m just not going to think about it.

@troyboyd7984 3 ай бұрын

Holy smokes. This a new one for me too. That exceeds "hack job" and goes straight to "attempted murder"

@TheManic.5-OH 3 ай бұрын

I mean... it was fine till you rebroke it, am I wrong? 😂😂😂 jk but seriously, 'that wasn't going anywhere' is likely the Magic chant the guy recited before lowering the car back down 😂😂😂

@Krankie_V 3 ай бұрын

Those words truly are magic!

Ең жақсы KZfaq

Пікірлер