Жыл бұрын
Пікірлер
@deweydodo6691 12 күн бұрын
Make it look so easy. My system seems to aerate and foam up the oil . Cracked pump I'm guessing now.
@roberthayes5037 26 күн бұрын
Thank you so much for these videos. I recently got an 8N tractor and your videos have been a life savers.
@briangastmeier3812 27 күн бұрын
Good job, no one explans bottom of coil and what spring sets on or the other part on front.
@daveholt248 28 күн бұрын
I have a broken Hydraulic Lift Side Arm on a 1948 8N Serial# 8N85920. Can you tell me if this is 37 Spline? I need to order the correct part but my tractor is in MI and I’m in CA. Thanks
@narcissistinjurygiver2932 29 күн бұрын
can anything be done to get more power?
@benkanobe7500 Ай бұрын
Your explanation was perfect! I now I can get it straight in my head (well, almost). So if I am running a brush hog do you recommend draft or position?
@benkanobe7500 Ай бұрын
Mine seems to work perfect in "Position" but in "Draft", my two arms go down further than in Position
@buckwheat7673 Ай бұрын
These videos couldn't be any better other than a mechanic coming to the house
@buckwheat7673 Ай бұрын
These videos are the best ever. Thank you, thank you, thank you!
@StopInfanticide Ай бұрын
Great video. Thanks so much.
@chrishorton6605 Ай бұрын
Yes, Awesome! Thanks for doing all this work. Now I understand how my steering works and how to adjust the backlash.
@BarkEater Ай бұрын
Where can I find the 12 bolt and castle nut set for ring gear? I think my factory rivets failed.
@KG-ed9eq 2 ай бұрын
Is there a reason the 9N 2nd and reverse slider gear 9N7101 is called out vs the 8N7101? Are they the same?
@user-mi9up2bn7v 2 ай бұрын
Awesome illustration.
@jjay718 2 ай бұрын
I did not see the thin thrust washer on my reverse idler just the thick one. Just checked my I&T manual and it says only some transmissions have 8N7029.
@jjay718 2 ай бұрын
Great videos. Thanks! I know we can just do the reverse of this video but would be awesome if there was a disassembly video too.
@chrishorton6605 2 ай бұрын
Beautiful graphics! Really makes instructions easier to understand.
@MiserKustoms 3 ай бұрын
these old engine are not as picky as a fuel injected engine. pretty much everything can be done at home with a few tools you will need to rent.
@Zfrostyone 3 ай бұрын
Very impressive cad work! Thanks
@americanjoe5486 4 ай бұрын
I have a factory manual that shows all that stuff it's just me getting my lazy ass out there and taking it apart
@pauldicus1530 4 ай бұрын
Awesome video. Thank you
@user-jz4es6vx1d 4 ай бұрын
Nice Job, Very helpful video for old 8N steering Gear Assembly, part numbers included make ordering parts simple. Thank You
@corybeard3426 4 ай бұрын
My manual says you can put shims behind brake cover and between cover and bearing retainer
@billstractorcorner 4 ай бұрын
WOW!! The quality of the animations is AMAZING. Great work!! And very detailed info, thank you so much!
@reggiemcdaniel1802 4 ай бұрын
Fantastic demo, the best I've ever seen.
@loraadkins1228 5 ай бұрын
where can i get whole gear shit assembly 1953 golden jubilee showed in viedo thanks
@stevenjohnson1756 5 ай бұрын
This is good stuff! Including the component part numbers is a major plus. Thank you for providing it.
@charlescase1026 5 ай бұрын
Just8Ns videos provide excellent demonstration of the various components. They are easy to follow and include part numbers. TTFN/CDC
@edupessina6371 6 ай бұрын
Super!!
@anthonyjohnson-dd1ln 6 ай бұрын
Cluth R/R next
@anthonyjohnson-dd1ln 6 ай бұрын
This would have been great, if I'd seen it last year when I did both axles and brake drums in the 48. 😊😊😊
@Just8Ns 5 ай бұрын
Next time!
@jerryf609 6 ай бұрын
Excellent video's. I have just rebuilt a TSX 33 for my 2N. I had a difficult time with the choke assembly. I thought i finally got it but the choke is closed by the spring and my float linkage doesnt open it. I can open it by hand by overcoming the spring but cant figure out how to keep it open after starting. I think i installed the choke plate wrong but cant find documentation on how to install the plate correctly. Please help. Thank you.
@user-bg2ed3ns4q 7 ай бұрын
My 8N 3 point hitch will lift great without a load but won't lift at all even with a 100 lb. load. Any ideas?
@Just8Ns 5 ай бұрын
SAFETY VALVE
@miguelmcwilliams7015 7 ай бұрын
My 3 point will not stay lifted..it slowly drops, and my draw/ float don't work. What do I need to replace?
@Just8Ns 5 ай бұрын
LIFT PISTON AND RINGS
@jhammond4344 7 ай бұрын
Man, the quality of this video is amazing
@jackpangaro4995 8 ай бұрын
Any chance you could send me the cad files you used? I have a class presentation today j the 8N Transmission and would love to use them for dimensions and I will make figures for a report
@Just8Ns 5 ай бұрын
NO THANKS!
@juanasanelli6831 8 ай бұрын
Tengo un N8 en reparación Los bujes están desgastados Su dueño no lo quiere reparar Estoy triste
@boydhughes8236 9 ай бұрын
How to purchase LG500 lift jig
@Just8Ns 5 ай бұрын
WWW.JUST8NS.COM
@terrymiler2164 9 ай бұрын
The main shaft front bearing is that press on.
@DerekBarkleyJust8Ns 8 ай бұрын
yes it is a press fit
@terrymiler2164 8 ай бұрын
@DerekBarkleyJust8Ns thanks I put a upper shaft assembly in,she's up and going.
@donaldkamula7931 10 ай бұрын
Great video!
@wvbonbonqueen 10 ай бұрын
I LOVE the way this video shows exactly where each piece goes, how it all looks once assembled too. Thanks, I had to subscribe as we have a 1948 8N to do some work on and I know we can find all the information we need watching your videos. THANKS!!! from those who aren't all that familiar with rebuilding tractors.
@DerekBarkleyJust8Ns 8 ай бұрын
thank you!
@luisbarcenas5330 10 ай бұрын
Thanks for you tutorial 👍
@DerekBarkleyJust8Ns 8 ай бұрын
you're welcome
@Dougf610 11 ай бұрын
control arm forked to control valve
@Dougf610 11 ай бұрын
9n different lid?
@Just8Ns 11 ай бұрын
YES IT IS...
@nairoroque7839 11 ай бұрын
Buen trabajo. Gracias por la explicación
@Just8Ns 11 ай бұрын
ERES BIENVENIDO!
@americansfirst1095 11 ай бұрын
Thanks! Helped me a lot on this rebuild,
@Just8Ns 11 ай бұрын
Glad it helped
@americansfirst1095 11 ай бұрын
Unbelievably great videos. Thanks!
@Just8Ns 11 ай бұрын
Glad you like them!
@MS-ew5ee 9 ай бұрын
It might be benificial to add to this video two important things. 1) the pistons are offset on their frames, these offsets need to face each other when placing on the cam blocks, and cam block flanges also need to face each other. 2) the bushing has a lip which rides inside the cam, the cam needs to be inserted with this shoulder facing the bushing. Just a suggestion. These videos are very nice, answers alot of questions during assembly. Thank you.
@Bekesam 11 ай бұрын
This is very well done and very impressive. Mostly, it's very helpful!!
@Just8Ns 11 ай бұрын
Glad you think so!
@americansfirst1095 Жыл бұрын
Super great video! Thanks!
@Just8Ns 11 ай бұрын
Glad you liked it!
@markbyfield7050 Жыл бұрын
All your animated videos are very well presented and very helpful. Thank you!
@Just8Ns Жыл бұрын
Glad you like them!