K series is getting boring, why not throw something new in the mix

I just bought one about an hour ago bout so some sheet metal with it so hope it works out good

never built it? is that why it was show cased at PRI?

Im glad i found your channel, just picked up a 1960 for my son. We are going to be learning as we go! Looking forward to more f100 videos.

thanks for the info

power from the wall to foot switch red to power supply where is the other wire go off the foot switch.

I raced mini modified for over 20 years we got 300 hp out of a 2 .3 pinto with 2 barrel carb no turbo and cost was less that 2000 put a turbo on it and your over 500

What gas setup are you running

Very nice!!

oh my.... that's sounds lovely lol. good stuff can't wait to see it going down the road

Благодарю за данное видео,благодаря которому я нашел необходимые комплектующие для данного проекта по подключению лебёдки к станку!

My guy stop lying, losing research. I went to the car show and saw this same engine on the stand.

😂Why would you use a Windsor head compared to a ls it doesn't flow worth a dam hell a magnum head from the 90s will out flow it how about a eagle version hemi head would clean house

Does it burns 6010 rods ?

I installed 2 and 1 is leaking. Im about to throw some red rtv between the flanges and hope it seals. Still better than the band clamp style

Where did you get the galley plug with the oil hole in it?? Did you drill it your self? Is it necessary?

That rear end shaft gets tiny towards the wheels never seen that axle tubes lol couldn't think of it last night is that a 9 inch or 8

I got the mig 170 works great

Do you have to weld these ones? Or are they going to be a better option then many stock vband clamps even without welding?

How much are you being paid?

I have a honda civic 1991 sedan. Can you please specify if it does fit on my model. Or any other suggestions.

Most definitely the best explanation of this I have seen great job!!

Is it heat and air? I need one for my 77 f150 but only want ac.

1970-1980’s mercuiser has a 3.7l ford half of a 460 it would be a hell of a car motor it might shake a bit though might have to shave the crank

Someone’s mad LS is gonna end the k series 😂😂😂

This is super helpful. Thank you for taking the time to put this up.

Way to keep it Ford ..... I had a 57 that I found a 312 Y block for it ... Kept it all original .... Loved that truck

Do you need to buy a hydraulic throw out bearing or can you leave the clutch fork??

Did you change out the master cylinder for rear disc brakes.

I’ve seen some people say it’s great, and others say it’s trash. I’m very conflicted.

What’s the feedback from it since it’s been a few months and it’s almost summer.

Thanks for taking the time to document your work, I am just starting this project on my 65 Ranchero

Just picked up my first Honda and have never heard of vband exhaust clamps till now. Thank you so much! Instantly subscribed

Where'd you pick up that brake switch? Love the factory AM radio & the dash mount tacho.. looks sick. I'm always checking ebay USA for period style dash tachos.. almost bid & won a chrome Cobra one from a 69 Torino,, but someone pipped me at the dying seconds DOH!! The Aussie 60's Falcons never came with tachos (or V8's) so it'd be pretty cool to have a nice tacho..

What kinda work do you do outside of the garage Rob? II think Michelangelo must've sculpted that Bondo quarter panel (we call it Bog, DownUnder..its more apt, i think..) Good thing you've gotta Zipdik🤣🤣🤣 Music sounds a lot like Clutch today.. great band from Canadia...love it The big '70 looked like Christine,,,,all disassembled & limping back into the garage all mashed up after killing Buddy Repperton... Hey why don't you paint it Grabber Blue 🤭🤭🤭

Oooh that looks like a scary job.. Lucky i saw the finished car before i watched this one.. Big Balls mate,,, Big Balls

Is that door hanger jig a home made jobby or did you buy it? Looks like its really handy. With the guard on (fender) & the door & bright work on,, it looks flash as fuck!!! I know it was a year ago for you,,, but its all new to me.. Bloody beautiful 💥💥💥

Great little run remover is a tungsten square blade,, its about the size of a a Scrabble square but totally made of tungsten,, you can shave the runs out clean & saves time because you only hit the run & not the adjacent area as well,,& it never gets blunt,,, but your repair turned out perfect. Love the colour... but it needs some satin black black-outs...Ohh, you're gonna do that..😂😂 See how i make notes as I'm watching,, LOL Such a satisfying colour... It looks wringing wet & deep.. awesome used to keep a spray bottle of water & occasionally spray the panel to keep the pad from getting too warm & burning thru..it does cause a lot of fling off & your shop gets spattered with compound but the finish is glassy. Beautiful job tho mate... you gotta be happy with that..🤙🏽🤙🏽

Good job you chose this Grabber Blue,, it'll be safe now from the DEW's.. there's really handy gallon lids at the paint shop that come with spouts set in them, makes for an easier pour. Another thing i learned painting was to bring in the garden hose before you spray & being careful not to wet the body & mist on a light layer of water onto the floor..it keeps the fine dust down when you're dragging the hose & shuffling around with your shoes & the overspray is attracted to the wet floor so it sits down quickly & reduces some of your overspray. Love the colour Rob

Good job mate.. and you're right about the blocking.. when you think you're done blocking back... do 20 more hours blocking back... Wax & Grease remover inflation.. that's Bidenomics 😵😵😵 Loving the masking-up music today..🎸🎸🎸🤘🤘 Big Worm... you bragging about what you're packing' ?? Pollen ? or chemtrails?... Spraying in one hand & camera in the other,, degree of difficulty 9.5!! Was good to see you strain your primer.. saves a lot of fixing later after the gun spits out a big lugie on the job hahaha & you're spot on about the bare steel, that'll react & boil the edges if you don't cover them bits up.. You the maaaaan..!!

Good stuff mate.. I had a custom paint shop years ago in another life, but only painted bikes..Big panels like that were never on the menu.. good to see how you tackled it.. took me back to those heady days.. i could even smell the filler & dust..

Dude... whaddjasay???🤣🤣🤣 Loving the steel-cap Crocs workshop boots... Safety first..Aaaannd.. I wanna see you sporting those bib & brace overalls next time too..Like Grandpa's.. You should bring that back.. Nobody else in YT is wearing them in the garage.. you would be unique 😆😆😆 💥Bless you💥 Don't you hate getting sparks in the beard... man i hate that. Mine's insured for $100,000🤣🤣 Diet Coke!!!!!! That's drain cleaner man...!!!! Welds are great mate & the way you've got it all tucked in so snug.. Good stuff🤙🤙

Awesome Rob,,, I'm calling it a transmishall from now on.. beautiful welds on that header mate..I know i'm watching the videos in the wrong order now,, but i feel like i gotta watch the old ones..since you made 'em. Time for a new video i reckon.......

Dont care if this thing comes out it will be badass.

Its because it doesn't have a Blue oval on the front

Nice work mate,, I really like how you're not scared to have a go at everything.. Be the boss of that steel.. 👊👊

Ahhhh nice... & some rockin' Blues harp to boot..Ohhhh I spoke too soon 🤣You didn't wanna try to lead-wipe that C pillar join? Cheese grater,, we call it a speed file or a Surform file. Guide coat dry,, i always used to get the cartriges from photo copy machines,, when the black cartridge was empty & replaced where i worked they'd toss it in the bin, but there was always heaps left in there.. I'd take it home to my shop & drop it in my guide coat tin. It had a round dense soft sponge under the lid.. you shake it up til the powder from the ink cartridge would lay on the sponge then just wipe it over the repair.. real easy to use & refilling it was free👍😁 great work Rob.. You fill me with confidence hehehe

Just wondering cobber, what height is your shop ceiling? I was thinking i'd need to build a shop with a roof height over 4metres (13 plus feet) to fit a hoist in.. But yours duzn look that high. The old man's one is fukn flash!!! Cheers

Nice mate,,,My dad had a '61 Falcon wagon when we moved th Oz from Ireland back in 1969.. I have a polaroid picture of me as a 3yr old sitting on the roof of it when we were parked at the side of a bush road.. Coming from the UK this Falcon felt to my old man like he was driving a boat after all the 'miniature' English cars he's owned & he called it his "Yank Tank"...So when the chance came up, i bought an old Falcon wagon like dads.. mine is the Aussie XP model 1965 & now she's a 302, soon to be 347.. if time & money permits. I don't have a great workshop like you have but there are plans (in my head) for one with the hoist & a host of new tool toys. You've got great skills mate, & i am really happy i happened across your channel.. Keep up the great work & the informative videos.. You've gotta mate here in the West Coast of Oz.. Cheers, Cobber.

Great little custom job mate, i reckon you'd pay $40 Aus for a dinky-chocolate one from Chy-na... which is about $26.70 in your money.. So for a custom monogrammed one i'd say $49 USD for a bare steel one & $20 more for the powder coated model. I really wanted to see you make the top with edges & breaks so that is wraps the top of the battery top & bottom, rather than just a flat flap piece of tin, which obviously would be more work, but you could add dimples in the top for strength & make it more interesting & sell that one as a premium model..& chrome it..!! $150 bucks I'd buy one from you but I'm putting my battery in the back of the wagon & dropping in the floor somehow.. in 2055 probably. Love your work Cobber..