Qosmokid

Пікірлер

@ferrer9609 2 күн бұрын

hiiii may I know how to make the MUX as an "output" for those buttons with led for on/off and fault. I would like to extend my output by using MUX. Thank you!

@Qosmokid 2 күн бұрын

@@ferrer9609 Hello, you cannot use an output MUX by itself to light up LEDs. You need to also use an LED Driver like my favorite the DM13A. I have a video on using those and you can connect the DM13A to an output MUX pin. It gets a little more complicated with those buttons that have LEDs in them so I do plan to make a separate video on them.

@Qosmokid 2 күн бұрын

Here's my old video on using DM13A's. I will eventually update it so I can show how it's done in the new configurator. kzfaq.info/get/bejne/mcmBjJdqpq63h6s.htmlsi=cx1oEMnNlbrn45hI

@FirstLast-pf3nv 3 күн бұрын

Muchas gracias por todos sus vídeos. Llevo mucho tiempo siguiendo sus enseñanzas y encuentro que (a pesar del idioma, que a veces me resulta algo difícil) son muy aprovechables. Muchas gracias de nuevo por sus esfuerzos en poner al día los vídeos previamente publicados. Esperamos con impaciencia nuevas aclaraciones.

@Qosmokid 3 күн бұрын

Gracias por su comentario. Me da gusto saber que les benefician mis videos. Como sabe, quería tratar de hacer todos mis videos en español pero me desanime muy rápido porque los pocos que grabe en español solo unas cuantas personas los ven. Me cuesta mucho tiempo grabar y editar cada uno y por eso ya no hice más. Pero si necesitan que les aclare algo solo dígame y trataré de aclarar.

@robertmania9498 4 күн бұрын

Thanks for your videos!

@Qosmokid 3 күн бұрын

You're welcome Robert

@edsondias1176 10 күн бұрын

SIMPLISMENTE INCRÍVEL PARABENS POR SEU CONHECIMENTO , É INSPIRADOR ABRAÇO

@ferrer9609 15 күн бұрын

hii can you do a vid how to connet a digitalLED to the overhead batt for a320

@Qosmokid 15 күн бұрын

Hello, I have already made a video on using LEDs but eventually I will make an updated one. Did you already see this video? kzfaq.info/get/bejne/g76RiKqGl9KcmJs.htmlsi=bPC4RXk0Stcp8LwO To assign it to a specific keyword you just need to go to the aircraft maps and select the function you want just as in the examples I used on that video. I don't own any Airbus airplanes in X-Plane so I can't use that one as a specific example but the procedure is the same. Let me know if this helps or if you need further clarification.

@tzampini 17 күн бұрын

Great content as always. Regarding your audio volume, It is somewhat lower than other KZfaq videos, but it’s not bad. For your video I have my volume at around 75% whereas for other videos about 50% is a good level. 😊

@Qosmokid 17 күн бұрын

Thank you Tzampini, I did some testing this morning and found that I could rise the mic volume in OBS quite a bit and it won't clip so the next ones should be better.

@philnelson2364 18 күн бұрын

You need to increase your audio by alot. I usually have my TV at 30 to 40. For your video, I need to go as high as 90. When another video plays after yours, the audio is super loud.

@Qosmokid 18 күн бұрын

@philnelson2364 Oh really, I have my mic at 100% and in OBS the audio bar goes into the yellow. I'll do some more testing before I record the next one. I hear some podcasts that are always clipping and it's annoying so I'm scared of doing the same 🤣

@allmightyx7600 18 күн бұрын

They really went cheap on the buttons, I've got one, and its nowhere near the quality build of a Victor/JVC.

@Qosmokid 18 күн бұрын

@allmightyx7600 Yes, they did. No wonder most of them have broken. They seem very brittle

@FlightSim2703 22 күн бұрын

Hi my friend good to see you again 🥰👍

@Qosmokid 22 күн бұрын

@FlightSim2703 Hello B, thank you. Good to come around once in a while 😁

@tedtheoldboyA320 Ай бұрын

Thank you so much for this video. I am an 80 year old mechanical engineer and find the physical making of the hardware for my Flight Factor A320 Airbus and X-plane 11 relatively easy but getting this hardware to 'talk' to my computer is another matter. With all of your previous videos you help me, and a lot of people, to setup Simvim. Then Simvim changed. I know there is all the information on the Simvim site to explain how to use the new program but I need someone to actually show the basics, i.e. what to click on etc. This you have done brilliantly in the past. I did not know what to do and went to your channel earlier this year thinking you would be on the case but nothing. The last videos on Simvim were several years old and I thought that you have moved on so to speak. I checked in on your channel again just now and you are back. Thank you for what you have said about the new Simvim so far as this has helped me quite a bit. I look forward to your future videos and again thank you so much for taking the time to make these videos.

@Qosmokid 28 күн бұрын

Hi there and thank you for the kind words. It's comments like yours that don't allow me to walk away from making videos. It makes me happy to hear they help people get to build a home cockpit or even just a button box. I am planning to continue re-recording all my videos that that based on the old website, configurator, and plugin versions. I've been quite busy with travel for work lately so it's taking me a lot longer than I hoped to get them done. Keep checking back and hopefully soon you'll be pleasantly surprised.

@DaveWrightKB9MNM Ай бұрын

Still trying to wrap my wee little brain around the mux thing. I'll get it eventually. I'm currently building a helicopter collective that uses potentiometers and need to figure out wiring those up.

@Qosmokid Ай бұрын

Hopefully you'll get it soon Dave, it's not that hard once it clicks. I do have a video on potentiometers too. Not sure if you've seen that one.

@DaveWrightKB9MNM Ай бұрын

@@Qosmokid I’m sure I have, I think I’ve seen almost all of them, but I’ll revisit 😊

@Qosmokid Ай бұрын

Disregard, I think I haven't made a video on those yet

@DaveWrightKB9MNM Ай бұрын

@@Qosmokid I shall wait…patiently 🤣

@mikebrown2618 Ай бұрын

Despite what is an excellent and instructive video I am still unable to get the Multi Panel Auto Throttle to become the parking brake control. has anyone else managed this please?

@Qosmokid Ай бұрын

Thanks for your comment mike. I'll give it a try and report back.

@Qosmokid Ай бұрын

Ok so I tried mapping thee auto throttle switch to the parking brake on the Zibo and I couldn't. No matter what I did, it still enabled the auto throttle. I even went into the FlyWithLua script and deleted a few lines pertaining to that but no luck. I was able to map a switch on the switch panel though.

@Qosmokid Ай бұрын

I tried it also for the default C172 and couldn't accomplish it either. Actually I hit a road block because it seems my .ini file was not even getting read after I made changes to it. I had to give up for now because it was getting frustrating 🤣

@mikebrown2618 Ай бұрын

@@Qosmokid Thank you so much for your kindnessmin doing that. If you cannot do it with your experience then I suspect my efforts are also doomed to failure. I have treid for two day and got nowhere. LIke you the auto throttle still kept working no matter what I did. I think I will have to map te parking brake to a switch on the quadrant and see if that works any better. Once again many thank for trying.

@JKarle Ай бұрын

Thank you for your videos, and PLEASE do not make them shorter. I do not find the SimVIm webpage entirely user friendly and that it seems to lack sufficient information for those of us who are just approaching this system of systems for the first time - your series of video are excellent, and perfectly focused on concept, explanation, and application, Keep it up!

@Qosmokid Ай бұрын

Thank you for your comment. The topic of this video is another one that I have to re-record since the website and custom conversion look nothing like in this video.

@JoLo-vx1nb Ай бұрын

Excellent comprehensive video!!!! I would like to request another future video. Please check the selection and multiple append Simvim software capability. I have one input mux pin that has 0-9 appended items for that one pin. I also have another input mux with a 10 position rotary switch used as the one selector (#1). The selector (#1) does not just pick and modify the proper selected (0 to 9) item out all the items appended on that pin but all the appended items at the same time. I properly assigned the one selector (#1) and the item number (0-9) per the selector input dropdown list for each item separately. I believe there is a Simvim software problem. I need this capability and I believe many other builders will also. Please provide an example of this capability in a future video. I think I implemented this capability properly per there website.THANK YOU !!

@Qosmokid Ай бұрын

Hi there Jo-lo, yes I will make a video on selectors. I'm a little confused with what you tried to describe though. You mean that when you change the position that the selector is in it changes the function of all the pins on the other 10 position rotary switch? Not just that one position it's supposed to? Or if you could send me your CFG file that has those assignments an also a brief explanation of what you are trying to do with that selector.

@Qosmokid Ай бұрын

For some reason I have a feeling you might be using selectors wrong or you might be misunderstanding how they're supposed to work. I've read your message like 10 times already trying to figure out what you are trying to get it to do but I'm still confused. Usually you would use a selector to change the keyword/function that a single push button, toggle switch, encoder, display shows. Are you treating the 10 positions of the rotary switch that's not the selector as 10 separate switches? Because you can't append multiple functions to rotary switches. Sorry JoLo, I am really confused 🤣

@JoLo-vx1nb Ай бұрын

@@Qosmokid I will gladly send you my small config file. Please tell me how to do that. I do not have your e-mail address. I can see why you might be confused based on your response and my description.. The 10 position rotary switch is used as the selector. It selects one of the 10 appended items appended to each one of 5 input mux pins so as to change their control of a particular x-plane's function. What I am trying to accomplish is to use one rotary encoder to change the heading, altitude, nav, com, crs, baro, ( fms, or range for G1000-3) and ( fms or range for G1000-1) a total of 10 items, The rotary switch selects which of these previously mentioned x-plane controls will be influenced by the rotary encoder. The rotary encoder is implemented by push buttons not by an actual rotary encoder. Confusing? ---Probably. I am building a generic cockpit which will serve my needs, THANK YOU for your interest and time.

@JoLo-vx1nb Ай бұрын

Sent you my conf file for your consideration . THANK YOU!! Realized I had your E-Mail address.

@DaveS_WI Ай бұрын

Nice job on the video. I really feel that SimVimX is a very underrated tool.

@Qosmokid Ай бұрын

Thanks Dave, yes it is. Especially now that most people are probably on MSFS and Mobi Flight has gotten huge.

@tzampini Ай бұрын

Fantastic video. Your videos are so helpful. Thank you for sharing with us.

@Qosmokid Ай бұрын

Thank you, you're very welcome

@FlightSim2703 2 ай бұрын

I have an exciting news, I did find a solution to fix my data, which I had previously loaded in to plugin, I renamed the data to data.cfg so that allowed me to be able loading the cfg file and saved it once again as data.cfg and replaced it with my original data, everything start working like before, seven segments and all knobs which control my cockpit are recovered. 🥰🤝🤝👌

@Qosmokid 2 ай бұрын

Yes that exactly what I showed you need to do in my other video to convert old cfg files to the new format. Glad you figured it out.

@FlightSim2703 2 ай бұрын

Good morning Jose 🤣👍 I'm so happy now, finally I figured out my external panel start working, also recovered the knobs which was made by simvim data start working, I'm so excited to fix couple more buttons on my gps and brake light to fix, all thanks to you and Val. 🥰👌♥️✌

@Qosmokid 2 ай бұрын

Good morning, that's great news. I'm glad you got it working also glad I could help. 😀

@damaso111 2 ай бұрын

Hola amigo un placer saludarle y tener tantos vídeos muy interesantes, es una duda que tengo. Yo toda mi cabina y todos mis paneles lo he programado con realsimcontrol, a un compañero le he fabricado unos paneles de radio iba a aprobarlos y resulta que todo el configurador y el interfaz de real sin control ha cambiado,y no se como se genera el DATA cuando le metes los pines al configurado me podrías ayudar ???gracias y saludos desde España

@Qosmokid 2 ай бұрын

Hola Damaso, gracias por tu comentario. Tengo un video que hice hace un mes explicando los cambios a el configurador y las conversiones. Si hay algo con lo que ocupes ayuda después de ver ese video no dudes en preguntar. Pero la respuesta simple es que tienes que precionar el boton "SAVE CFG" para generar y guardar la configuracion. kzfaq.info/get/bejne/e51mZMdmr9-ymHU.htmlsi=O_Z_IKiOogrZhbYp

@FlightSim2703 2 ай бұрын

So many changes recently with simvim this changes made me disappointed so I give up, disassemble all my cockpit and selling the parts , well let's start first with my "Saitec pro flight" see who is interested 🤔

@Qosmokid 2 ай бұрын

Oh that's a shame because even though they change the way the website looks it doesn't affect a setup you had already built. I have never had to do anything to my setup even through 5 years of SimVimX changes. 😁

@edsmith6504 2 ай бұрын

Lasonic. A name you can trust from a flea market seller you can trust.

@mog_millzy 2 ай бұрын

Broo I want this so bad but it costs 2-3k

@Qosmokid 2 ай бұрын

Yes, they are getting ridiculously expensive

@dixielandfarm 2 ай бұрын

Once again - I appreciate the developer always making something better - but I also appreciate that other systems have remained static for six plus years so you don't have to do anything once its done, ever.

@Qosmokid 2 ай бұрын

Hey there, I totally agree on that. Hopefully, they'll get to the point that SimVimX will be considered finished soon 🤣. I'm just glad that even though all the changes, I haven't had to redo any of my wiring at all.

@dixielandfarm 2 ай бұрын

So neat seeing the old boxes - I can't believe you kept them all!

@Qosmokid 2 ай бұрын

Oh man I'm a pack rat. You'd be surprised how much stuff I have from the 80's and 90's also

@Altrote100 2 ай бұрын

Tremendeus setup bro!! Your work is excelent!! and all in the same space since the begining

@Qosmokid 2 ай бұрын

Thank you, yes you noticed it's all on the same desk 😁

@marvinwhittaker 2 ай бұрын

I have a radio like this. I had it for 30 years and it still plays.

@Qosmokid 2 ай бұрын

That's great. Have you ever had to recap it or do any service to it?

@marvinwhittaker 2 ай бұрын

@@Qosmokid not really. Only the radio part works. Like the cassette player, it plays a little faster.

@TonyHA913 2 ай бұрын

We use to be able to use output multiplexers with 7 seg displays, is that not the case anymore? we can only assign 7 seg displays directly to the arduino pins 30-37?

@Qosmokid 2 ай бұрын

Hi Tony, we still can, I mentioned it in the video. You can have up to 64 7-segment displays on 4 output multiplexers. At around 4:35

@TonyHA913 2 ай бұрын

@@Qosmokid Oh thx I missed that.. I was confused about what you said at around 8:00 .. I just tried it, it is not that much straight forward but not too complicated as well. I feel like the older configurator was much easier to use or maybe it is just me !

@Qosmokid 2 ай бұрын

No, I kind of think it was easier in some ways too.

@SimPilot-dl8zy 2 ай бұрын

Another great video.

@Qosmokid 2 ай бұрын

Thank you

@JoLo-vx1nb 2 ай бұрын

Thank You once again for your excellent videos. When and if you present a video on how to do conversions -- please consider how to display --- an airplane's Pitch and Roll degrees --- on an LCD display. I have not been able to do this. THANK YOU !!!!

@Qosmokid 2 ай бұрын

Thanks for your comment. Ok I will definitely do that. Is there a specific airplane you have in mind? Although I think you do not need to do conversion for those parameters

@JoLo-vx1nb 2 ай бұрын

@@Qosmokid Thank you for considering my request. I believe the Pitch and Roll degrees I am requesting apply to all aircraft. However, I am presently generating a configuration for the basic Cessna 172 (G1000) aircraft. I am especially interested in displaying Pitch degrees. This parameter along with possibly the yoke pressure parameter ( I believe this parameter is available also ) will allow me to control "slow flight" and " level flight" effectually. THANK YOU !!!!!!

@Qosmokid 2 ай бұрын

Ok so I tried setting up the datarefs you are asking about and because they are default xplane datarefs it won't let me put them even on a "GENERIC" LCD Display. I just had Vlad work on fixing an issue on the Zibo so I'm going to wait a little before asking him if this is something he can add lol

@joseivanbeau 2 ай бұрын

My first sim was MSFS 5, back 94. since then I got all the copies.

@Qosmokid 2 ай бұрын

Wow that's awesome. I just saw a video on FS4. I'm going to look up one about 5

@joseivanbeau 2 ай бұрын

The history of my life, our computers were good enough, not those old versions cannot run like we want to in the new computer, Now MSFS2020 runs perfect with some glitches.

@ripjanetstrimel3312 2 ай бұрын

Nice I have the same one love these

@tonylitvak3198 2 ай бұрын

wanted to thank you again for all of your great work. Ive built a nav module, using simvim but have decided to swap to mobiflight in the future - concerned about long term viability of the product and dont want to be in an unsupported mode 2 years from now. Have you ever considered doing videos on how to build panels using fusion and cnc - thats my next hill to climb. Again great job with the videos!

@Qosmokid 2 ай бұрын

Hi Tony, thank you for your comment. I don't worry about SimVimX going away. They've been working on this project since 2011. I just hope that if they do decide to stop working on it they would leave the website up so that people can still do configurations since we don't have a standalone program. As far as your question, no I don't even know how to use Fusion and I don't have a CNC so I definitely would not be able to do that. I hope some day to get at least a 3D printer.

@Nickgowans 2 ай бұрын

When youtube sends you to just the right kind of video but then you have to delete it from your history in case your wife finds out you watched it

@Qosmokid 2 ай бұрын

🤔

@DaveWrightKB9MNM 2 ай бұрын

Jeez, FS95 was my first and when I learned how to navigate via IFR and using VORs and such. Flew out of Meigs Field in Chicago.

@Qosmokid 2 ай бұрын

Hi Dave, Oh man I remember Meigs Field, so you started with FS a little before me.

@DaveWrightKB9MNM 2 ай бұрын

Hey, appreciate your video! Very inspiring to get back into building. Here is a thought: use a second PC for instrumentation. I know in SimVim Vlad has an example of how to. Just to help free up resources for the main pc. I’m in the process of building a helicopter collective and it uses potentiometers and MobiFlight seems way too complicated for me. I need to go back through some vids to get multiplexing figured out and the new format of SVX is hard to figure out. Will be anxious to see your new tutorials! No pressure lol 😊

@Qosmokid 2 ай бұрын

Oh I'm glad you're getting back to it Dave. I already have one more recorded. Just need to finish editing and post it. The updated multiplexer one will be after that one. Yes sir, I need to use SimVim Panels, I can use one of my laptops for that or take the raspberry pi 4 out of my mini arcade cabinet 😂

@DaveWrightKB9MNM 2 ай бұрын

@@Qosmokid fly or arcade, fly or arcade..lol 🤣

@jankristensen7884 2 ай бұрын

I considered Simvim, but ended up with Mobiflight..they are very similar, i just think the support at MF its superior

@Qosmokid 2 ай бұрын

Yes they do have very good support and the creator makes tons of videos too. I've only researched it for the comparison video I posted a few years ago. Just watching some of the videos it seems a lot more complicated to configure. It does have it's multi simulator advantage though. Maybe soon I will give an honest shot and discover it's not as complicated as I think it is.

@activex7327 2 ай бұрын

@@Qosmokid yes it does, xplane and msfs

@ShahidKhan-uw2ix 2 ай бұрын

These guys at Simvim are keep changing the entire process. You go to their website just to find everything has been reshuffled. Other problem with Simvim, is they put too much irrelevant information and it looks like ton of cluster F. There is no clear information about how things work. You have to keep trying to make something work. They built the site and left it for you to "Go figure". It is sad that without your videos their website is as useless as ashtray on motorbike.

@Qosmokid 2 ай бұрын

🤣 yikes, those are some pretty harsh words. I appreciate that you find my videos useful. I actually think their website and instructions are very good. They separate all the wiring technical stuff by component. You are right though about the assignments and conversions. They try to make it as clear as possible but I did have to figure out some of it on my own 😁 As far as changing everything, I know they are trying to make it as good as possible and I understand that. They also do mention that it is in active development and it can change as any time. 🤣

@jorgeferreira6727 2 ай бұрын

Hi. Nice work, I never get to that level myself. BTW, your hand painted panels could be easily improved by just printing them on plain paper with a common printer. The button graphics can be printed in self adesive paper.

@Qosmokid 2 ай бұрын

Thank you Jorge, yeah I've thought about that for the printing and also considered getting a label maker that does white on black.

@737simviator 2 ай бұрын

WOW. Flight simulator 2002 was my first sim, it inspired me to take my first flight 3 years later. Thankyou for the memories Sir

@Qosmokid 2 ай бұрын

That's awesome. I miss flying, haven't been up since 2008 🙁

@Amigosworlds 2 ай бұрын

Спасибо вам за большую проделанную работу. Благодаря вашим видео я создал мини панель управления 172с. Не останавливайтесь, продолжайте!

@Qosmokid 2 ай бұрын

Nice to hear that, you're welcome & thanks for the comment.

@SimPilot-dl8zy 2 ай бұрын

Good video. Keep it up.

@Qosmokid 2 ай бұрын

Thanks, will do!

@johnstrandberg2035 2 ай бұрын

What a journey, keep the videos coming 👍

@Qosmokid 2 ай бұрын

Thanks John, I'm trying 😁

@johnstrandberg2035 2 ай бұрын

@@Qosmokidcould I email you, I have a couple wiring questions for some switches

@Qosmokid 2 ай бұрын

@johnstrandberg2035 yes of course, it's qosmokid at gmail

@robertvasco9950 2 ай бұрын

I had that

@emc3895 2 ай бұрын

You do a great job and thank you for taking the time to share all of this with us! I made a prototype MCP for my 737 Zibo in Xplane 12. I have a problem: when I fly in VNAV and LNAV, if during the descent I need to slow down the speed of the plane, I noticed that the SPD INTV button does not work on my MCP, yet it sends the information to ZIBO which then displays the speed to modify on the 7 segment while the speed of my MCP remains empty! At this moment, I cannot reduce the speed with the speed rotary switch which remains inactive on my MCP. However, on ZIBO you can reduce the speed of the plane with the mouse! I have tried several times to contact Vlad to report this bug but I have not had an answer on this subject. Do you know how we could solve this problem? I tried to see if we could access the code but even with Sublitext or Arduino IDE software I couldn't! Thanks for your help The video of my problem : kzfaq.info/get/bejne/nZaBmbWhzcyWc6c.html

@Qosmokid 2 ай бұрын

Thank you EMC, I replied to you on your video comments.

@emc3895 2 ай бұрын

@@Qosmokid And I replied to you too 🙂

@emc3895 2 ай бұрын

@@Qosmokid kzfaq.info/get/bejne/oJOgkpict7i6on0.html

@Qosmokid 2 ай бұрын

Ok good news, I got in touch with Vlad and he fixed the issue. I just tested the new dat file and both the display and the encoder work perfectly. I'm sure he'll post the new dat file on the site as soon as he reads my message that it was successful.

@emc3895 2 ай бұрын

@@Qosmokid I am very happy to read this news... I use this function a lot when I fly my 738, especially when going downhill. I tried so many times to report this issue, you had more luck than me, well done!!! Thanks for your help ! I can't wait for the update!!!!

@Glasairman 2 ай бұрын

Hi I used this tool to find Toliss AirbusFBW Datarefs which are not published and are are not picked up by the Dataref Editor. All the Datarefs you show here are integers or floats and I have had no probs in setiing them from an external program. However many of the AirbusFBW datarefs visibie in the DataRef Tool just say 'activate'. Without knowning what activate means internally, it's hard to enter a program value that changes the Dataref state. Do you have any information perhaps?

@Qosmokid 2 ай бұрын

Hi there, unfortunately I don't own any FBW aircraft so I can't look up some of those datarefs you are talking about. The only weird think I have seen with some datarefs mostly with lights if I remember correctly is that they are arrays. Those are the ones that have a bunch of numbers separated by commas. I don't understand arrays so I couldn't even begin to try to explain them to you ☹

@flavianojose8423 3 ай бұрын

Hey my friend, long time no seen your! welcome back. And yes, simvimx remains the best comparing to other namely mobiflight, as it is easier to connect your switches LEDs and so forth. however I still believe that is lacking somewhere which is making it open source and create external independent app as mobiflight made it, if something has to happen and the website goes down as well, we are all gonna hangup, I have now 4 simulators, connected to simvimx and they are all connected to the old configurator, and guess what, I will have to reprogram everything again to the new one because many of the systems stopped working with the new configurator, and that is pain, a complete good solution would be to make it open source and create an external application like mobiflight to make it much easier

@emc3895 3 ай бұрын

Thank you for these very clear explanations. I will start my connections soon and I found information here that I did not find on the SimVim site (the power of the resistors that you tested in particular)

@Qosmokid 2 ай бұрын

Thanks, if you watch my other video, "Playing with LEDs" you'll see that pretty much you can use whatever value you want as long as you prevent too much voltage from getting to the LED. Some are way too bright even with the recommended value.,

@efrenkov 3 ай бұрын

Hola amigo. Sigo con el error de que no se muestra el IAS MACH en el 737 por defecto del x-plane 12, no es problema del 7 segmentos, es algún error del plugin, Con los últimos SIMDATS no se ha corregido, ci abro otro avión un A320, 737 Zibo entonces si se muestra el IAS MACH. Antes de la actualización 2.20 no pasaba eso, sabes algo al respecto??? AP_SPD_Cmd o=1 Lo tengo en el MAX 7219 . Muchas gracias

@Qosmokid 3 ай бұрын

Hijole disculpa se me paso completamente investigar ese problema. Otra vez no estoy en casa esta semana por el trabajo. Cuando regrese el fon de semana lo hago.

@efrenkov 3 ай бұрын

@@Qosmokid Cuando puedas, te lo agradezco, en foros y demas no veo nada

@Qosmokid 3 ай бұрын

Hola, finalmente llege a mi casa y tuve la oportunidad de provar el problema que me dijiste. En mi caso si me funciona perfectamente. conecte un MAX7219 y le asigne el AP_SPD_Cmd keyword y muestra los numeros correctos. No se que pueda ser el problema con el tuyo. La unica duda que tengo es que si no te muestra ni el AIRSPEED o solamente el MACH?

@efrenkov 3 ай бұрын

@@Qosmokid HOLA, he logrado que se vea poniendo esto AP_SPD_Cmd_Kts o=1 ya que uso un display de 6 segmentos, lo que no logro ver el al pulsar C/O en el simulador si cambia a IAS. pero al menos logro verlo, muchas gracias por ayudarme. Un saludo desde islas canarias GCLP aeropuerto de gando

@DaveS_WI 3 ай бұрын

Hopefully you will be attending FSExpo in Vegas in June 2024 ??

@Qosmokid 3 ай бұрын

I do have a flight reserved, but there is a birth somewhere in that time frame so we'll see 😁

Ең жақсы KZfaq

Пікірлер