I realize this video is already 4 years old, but I'm hoping you still get notifications. Any idea how this will affect the factory airbags on an '03 Tintop? Wife's rig needs more defense against deer out here in the sticks, but I don't want to compromise the SRS in case of a vehicle collision.
@BarelyBuiltRight6 күн бұрын
Its hard to say. The sensor is still in place, so they should still deploy. However, the actual activation time may be microseconds different due to the bumper. Can't really say if its too much of a difference as I haven't set them off..
@NickLenarz5 күн бұрын
@@BarelyBuiltRight Thanks for getting back to me, I appreciate it. I'm going to go ahead with it, but as the stock frame horns are a little flimsy I think I'm going to box the frame horns 1/8" plate for a little ways and extend them, rather than putting the C channel extensions inside. I know the idea was no-weld, but I just think the stock frame needs to be beefier. I could just see that stamped steel tearing in an impact and the bumper and C-channel being just fine. Thanks for the fantastic idea and link!
@BarelyBuiltRight5 күн бұрын
@@NickLenarz for sure! Yeah you will be much better suited than mine with that plan. Don't reinforce toooo much as that will reduce the factory crumple zones in the frame rails. If they are too stiff they won't collapse correctly and the airbag sensor will be just a little too late, resulting in bags deploying just a little late. But a little reinforcement should be okay.
@michaelcampos13618 күн бұрын
Bro awesome !!!!! Keep it up and f…..k negativity!!!!
@BarelyBuiltRight7 күн бұрын
Negativity brings interaction, which promotes my videos to the algorithm! Haters bring me money 😂 thanks for the support!
@Invertmini121210 күн бұрын
Just dont hit anything with them 😂 They turned out great!
@JKram59912 күн бұрын
What tools do you need for this
@BarelyBuiltRight11 күн бұрын
I recommend checking out Fondupot Garage's video for more detailed tool info! He is a little more comprehensive than me. kzfaq.info/get/bejne/j9Ngp5Wbz7CveYk.htmlsi=fOc30OC3zI4ce7Oq
@PrettyLady728212 күн бұрын
super dope!
@coletrickle-km7cl13 күн бұрын
I also have a 1979 wet bike. Same James bond decal look also. I never got it running. I'd be willing to sell it. Good for parts.
@BarelyBuiltRight13 күн бұрын
Does the engine spin? Where you at?
@coletrickle-km7cl13 күн бұрын
@@BarelyBuiltRight I got in a barn in Tennessee. haven't touched it in years. So I don't know about the condition of the engine.
@BarelyBuiltRight13 күн бұрын
Right on! Might hit you up if I find myself in need. Thanks for stopping by the channel!
@coletrickle-km7cl13 күн бұрын
@@BarelyBuiltRight sure no problem. I got too many other projects that are not getting attention enough so the wet bike will remain water shy.
@coletrickle-km7cl13 күн бұрын
@@BarelyBuiltRight nascar driver Hailey deegan bought 2 wet bikes. She did a video about it on her you tube channel. She regretted buying them cause she didn't know how hard they were to ride. Wonder if she sold them?
@connorvallee113 күн бұрын
This is awesome. Can’t wait to see it be brought back to life
@BarelyBuiltRight13 күн бұрын
Hell yeah me too! Thanks for your view!
@Grassdestroyer114 күн бұрын
the goat
@BSS2219315 күн бұрын
Great work 👍 these sideskirts looks really good on your truck!
@BarelyBuiltRight15 күн бұрын
Thanks! Appreciate your view
@ironvic21719 күн бұрын
I did it on my trailblazer like I said. Came out freaking awesome! All credit goes to you for the great idea and video . Thanx bro 🙏
@BarelyBuiltRight19 күн бұрын
That's sick!! Love comments like these! Glad it worked out!
@Echo_Miguel_love20 күн бұрын
Good way to f up the truck, but it’s pretty creative, I like it, but I like dumb stuff😂
@BarelyBuiltRight20 күн бұрын
😅 its traded in now so nothing else matters lol
@dadsdog122 күн бұрын
I sub to see this icon rip.
@BarelyBuiltRight22 күн бұрын
Hell yeah thanks! Hopefully fulfill your request sooner rather than later!
@milesfifer17122 күн бұрын
Looks great 👍 it's cool seeing guys thinking outside of the box finding very affordable alternative ways to make automotive products, you'll have haters on this because they think you have to fall in line and spend hundreds if not thousands of dollars on these products, back in the 1980s I used to use vinyl house siding to form ground effects for cars and guys would where I got the custom parts because they loved them and after I told them they just laughed and walked away. Why? Because I didn't pay through the ass for something? Thanks for the video
@BarelyBuiltRight22 күн бұрын
Hell yeah appreciate the kind words! In all fairness, it wasn't my original idea, but I put my spin on it. Thanks for your view!
@a.a.492423 күн бұрын
You forgot to install the downspout..
@BarelyBuiltRight23 күн бұрын
😅
@pablpalma16748 күн бұрын
🤣
@LittlesliceOfheaven-og6cs3 күн бұрын
Or the kick out lmao
@mr_handsome2you23 күн бұрын
looks amazing, how does it hold up to children and big guys? does it crack easily?
@BarelyBuiltRight23 күн бұрын
Thanks! Its definitely not a step. More so for looks. Takes kicks and such just fine though
@keenanmatthews120823 күн бұрын
it would be way easier to uncouple the motor and disassemble on a table. my guess is a dingleberry hone, new bearings and seals. save the effort of rebuilding these carbs and just get some cheap ones online. fuel filter and pump. distributor will need contacts cleaned of replaced. IMO its a really cool simple motor that you can learn a lot from if you take it all apart and rebuild.
@BarelyBuiltRight23 күн бұрын
Thanks for the response! Sounds like pulling it is the next step
@keenanmatthews120823 күн бұрын
high quality vid for a small channel. You'll grow in no time.
@BarelyBuiltRight23 күн бұрын
And thanks for this encouragement!
@kittyztigerz23 күн бұрын
if i were you i would pulled engine out and put head back on block and filled up with diesel fluid and let it sit for 4 or 6 day and come back and try turning it surely enough it will come loose without fight at all i have done this so many time on every engine in boat doesnt matter vehicle or boat but still it one easily thing save your engine block from being destory by other
@BarelyBuiltRight23 күн бұрын
Appreciate your time writing this up! I will give it a try, thank you
@kittyztigerz19 күн бұрын
@@BarelyBuiltRight your welcome im engineer repairs i fix anything i find that broken and help people out with inform helpful save them headache and save engine save vehicle
@anthonysimpson284723 күн бұрын
best thing you can do at this point is pull the engine and break it down. You may get lucky and get away with just honing the cylinder walls, they do not need to be perfect as 2 strokes are a little more forgiving. The rings are probably seized in the piston groves if this is the case let them soak in evaporust gently tapping them until they break free then remove them and clean the rings and groves until they are smooth. i believe these have needle bearings on the crank and rods so I would start looking for them now because if they are pitted they will fail really fast with really bad results. the corrosion you see on the exhaust is pretty typical of marine engines and as long as nothing feels too thinned out by the corrosion it will be fine.
@BarelyBuiltRight23 күн бұрын
I really appreciate you taking the time to write this out! Great insight! Thank you!
@purepony24 күн бұрын
Awesome idea keep up the good. The trucks looking great!!
This is great! Ill try it on my trailblazer ss 🙌🙏 thanx for sharing your creativity bro
@user-hv8jb2bo9mАй бұрын
Looks good
@littlemiamijeffАй бұрын
How much extra weight between the added frame and bumper? Love this
@BarelyBuiltRightАй бұрын
Couldn't tell you exactly as I didn't weigh anything, but probably pretty close to stock. The factory steel bumper reinforcement gets replaced with the bumper only...
@littlemiamijeff29 күн бұрын
@@BarelyBuiltRight gotcha thx. Picked my new to me zr2 up today. 🔥
@BarelyBuiltRight29 күн бұрын
@@littlemiamijeff hell yeah! Congrats! I'm sure you will have a blast with it
@nomadbarka7407Ай бұрын
Shoulda glue screwed then sprayed
@markr4910Ай бұрын
Don't do this!!! Those plastic pieces of crap are gonna flap like your mother of 20mph, when you hit 70mph they are gonna rip off. If you are going to do something, do it right first time! Fibre glass or composite is a lot more ridged, alloy even more. Don't use self-fing tappers (that's the equivalent of using electrical tape) they will rust. Please please don't try anything in this video on your car, you will regret it!
@BarelyBuiltRightАй бұрын
You saved a lot of lives here today
@Alwhite1929Ай бұрын
Im in Michigan so i definitely won't be self tapping to the rocker panels. 😮
@BarelyBuiltRightАй бұрын
Definitely a good call!
@billerwin4983Ай бұрын
Otaly
@BarelyBuiltRightАй бұрын
Pweeblie
@danielcano7169Ай бұрын
👍👍👍👍👍👍👍👍👍
@richardvue5055Ай бұрын
With the truck being lower and low offset wheels with spacer, how is the suspension travel on it? Going over speed bumps/pot holes ect. does the top of tire touch the fender/bedside wheel housing?
@BarelyBuiltRightАй бұрын
When I first put the wheels and flares on the rear wheels chewed the hell out of the flares, but rarely made contact with the bed. Once they ate the plastics they "settled out" but would still catch occasionally when I would bottom out.
@davelowell3008Ай бұрын
Nice truck
@quibly2143Ай бұрын
Where can I purchase this?
@BarelyBuiltRightАй бұрын
Cars of Sarasota in Sarasota, FL
@lilRambocatАй бұрын
What did you use to drop the rear end? I'm thinking about just lowering mine to just level ...
@BarelyBuiltRightАй бұрын
Its a Belltech lowering kit. The rear utilizes the "axle flip" method which is putting the axle on top of the leaf springs instead of under them
@billsterling5790Ай бұрын
AWWWWWWWWWWWWWWWWW Daddy money...................
@BarelyBuiltRightАй бұрын
😂you must not have looked around the channel much
@bobbyserchionАй бұрын
Not bad man that's dam good 😊😂😅
@williamlittig7266Ай бұрын
should have just kept it white
@BarelyBuiltRightАй бұрын
Milk toast
@JamesJones-rg3dnАй бұрын
Gotta say,if there ever was a trophy for redneck hacks,this would be up there near the top of the list
@willecho8389Ай бұрын
So clean
@Grassdestroyer1Ай бұрын
gold tape
@theaussienurseflipper.8113Ай бұрын
Can't believe U did it
@BarelyBuiltRightАй бұрын
Neither can I
@JustinPaul1stАй бұрын
One year later can across the channel and video...We did the exact same thing for our VW Golf (Rabbit) and came out just as good...we went one step further and used the same PVC profile to make a fiberglass mould and make fibre glass skirting for all the guys in our group at the time...Just an idea for anybody reading this
@BarelyBuiltRightАй бұрын
Hell yeah! (But I think you meant to post this on my rain gutter side skirts video)
@JustinPaul1stАй бұрын
@@BarelyBuiltRight Yes you right...
@dozerdutyАй бұрын
I did this in 1986 on a '79 toyota Corolla... WOW!!
@webb3800Ай бұрын
Have U ever made another video on how to seal up the ecu box ? Idd like to know thank you
@BarelyBuiltRightАй бұрын
I have not but that is a good idea, thanks!
@06emily_Ай бұрын
June 4 8am we drove by your car
@BarelyBuiltRightАй бұрын
Awesome! Thanks for noticing and checking out the channel!