Thanks for making this video and giving me a good starting place.

How did bypass the security system to start with the screw driver mine pacifica cranks but wont start do to security codes

Thanks for the info. No wordy bantor, Directly to the relevant info. Brief, clear & consice explanation w/easy to discern images. A+👍

Don't give up your day job.

Great video and thank you!!!!

Thanks, brother. I appreciate you taking the time to show the rest of us!

My 4×4 light burns what can I do? Thank you for your help when you can help me.

how to reset bmw x3 2006

What model of new headlight assembly to replace stock one for Honda Civic 2001? Thank you in advance.

Question. Do you need a control panel ? Something other than the airbags too?? Thx

Hey uhh how’d you get the ignition out … did you have to completely take apart everything??

Does BMW use steering wheel fluid?

Is there steering wheel fluid fluid for BMW?

Does this work also on older models? on first gen 2004?

Tankyou so Much buddy👍🏻nice work

You are the first one to not go through another of un necessary steps thank you sir.

U changed starter when u knew it wasn't getting power 😂😂😂😂

Thank you! I’ve been in the parking lot at auto zone for 25 minutes trying to find a video that I could understand😁

Hmmm, not sure if the module needs to be replaced

Good to go. Did my 2013 Sierra SLE 4x4 in a matter of 3 minutes after pulling the tools out of my box. The handy hints you pointed out were great also, ie: being careful of the clips/snaps and to look for a metal one as well. I already ordered the plastic one though before seeing your video. Thanks again. You on TikTok? I am at TheThreeDawgs see you again.

Es aceite de la transmisión o del motor?

Actuator

Do I need to remove the lid off the master cylinder before starting?

2006 Chrysler Pacifica driving and car just quit off and I changed my crank shaft sensor and camshaft sensor and my car still want Crank why?

I got a 06 Pacifica but I'm trying to find out what's going on when I put it in reverse it cut off on me 🤷🏼🤦

I lost my key how do I bypass the invalid key and fob

Question When I am bleeding the rear breaks I don’t have any break fluid coming out what can it be.

I pushed my clock button but nothing happens

Same thing to my Pacifica 2007

Toda esta información tenía que ser España

Me gustaría que esto fuera en español

Worked perfectly for me - thanks.

Damn I don't have a 10mm.

Very helpful thank you

1The Module could be bad. Most likely need to replace the Module. You can buy a used one on www.eBay.com or send your Module for repair at www.myairbags.com/product-category/repair-return/airbag-module-reset/ Here is video kzfaq.info/get/bejne/nJqdd9SWrZrTZ3k.html

The Module could be bad. Most likely need to replace the Module. You can buy a used one on www.eBay.com or send your Module for repair at www.myairbags.com Here is video kzfaq.info/get/bejne/rrplp8yFl6ebaKs.html

Was it cranking at all before this? I have an 06 died while driving. Crank but no start replaced sensors and pcm, still crank but no start

did the car turn over at all before you fix the problem or not

Does somebody know where can I buy the airbags and the module?

You know

Great tip nd thanks for the help. Saved me from just yankin it off

2006 x3 3.0L. the the 2nd button 1000x and it doesn't do anything. not sure why

Thank you! You saved my Pacifica!

I tried that with my x3 and it’s not showing the oil level

And, does the new edge mustang have and exterior airbag sensor?,

Hello, I want to replace my exploted airbags of my 2003 mustang gt, I have the new ones, but do I need to replace the airbags module??

Had a code replace crankshaft and camshaft position sensor n when u drive bout 20 25 it bulkes then continues what could it be 05 chrysler pacifica thanks

Hola donde esta el sensor de las bolsas de aire

Best I found

you need to take off that black switch and put the cylinder in first and then connect that black clip after